1. Introduction
This manual provides detailed instructions for the setup, programming, operation, and maintenance of your Yinuogo YNG101 / YNG122 4-channel 433.92MHz fixed code remote control. This device is designed to clone existing fixed code remote controls, such as the NECO TX4, for various applications including garage doors, gates, and other remote-controlled systems operating on the 433.92MHz frequency.
Important Note: This remote control is compatible with fixed code remotes only. It is NOT compatible with rolling code remotes (e.g., Neco TR4 Rolling Code).
2. Specifications
| Feature | Description |
|---|---|
| Brand Name | Yinuogo |
| Model Number | YNG101 / YNG122 |
| Frequency | 433.92MHz |
| Encoding Method | Fixed Code |
| Buttons | 4 |
| Battery | Included |
| Certification | CE, RoHS, WEEE |
| Origin | Mainland China |
| Package Dimensions (approx.) | 8cm (L) x 8cm (W) x 8cm (H) |
| Package Weight (approx.) | 0.06 kg |
3. Setup and Programming
Follow these steps carefully to program your new Yinuogo remote control.
3.1. Clear the Remote Control's History (Reset)
- Press and hold buttons A and B simultaneously on the Yinuogo remote control.
- Continue holding both buttons until the LED indicator flashes 3 times.
- Release button B (while still holding button A).
- Press button B slowly 3 times. The LED will flash 3 times.
- Release button A. The remote's history is now cleared.
This process ensures that any previous programming is erased, preparing the remote for new cloning.
3.2. Programming Code from Original Transmitter (Cloning)
This method involves a face-to-face cloning process. Ensure your original remote is a fixed code type operating at 433.92MHz.
- Place your Yinuogo remote control and the original transmitter side-by-side, as close as possible. For best results, they should be touching or very close.
- Press and hold the desired button on your original transmitter (e.g., button A).
- Immediately after, press and hold the corresponding button on the Yinuogo remote control (e.g., button A).
- Continue holding both buttons until the LED indicator on the Yinuogo remote control blinks rapidly (usually 3-5 quick flashes). This indicates successful cloning.
- Release both buttons.
- Repeat this process for any other buttons (B, C, D) you wish to program.
For a visual guide, please watch the programming video:
4. Operating Instructions
Once successfully programmed, your Yinuogo remote control operates identically to your original fixed code remote.
- Ensure the cloned remote is within range of the receiver (e.g., garage door opener, gate opener).
- Press the corresponding button (A, B, C, or D) that you programmed for a specific function.
- The LED indicator on the Yinuogo remote will light up when a button is pressed, indicating signal transmission.
5. Maintenance
- Cleaning: Wipe the remote control with a soft, dry cloth. Do not use abrasive cleaners or solvents.
- Battery Replacement: The remote comes with a battery included. If the remote's LED indicator becomes dim or fails to light up, or if the range decreases significantly, it may be time to replace the battery. Refer to the full user manual (PDF) for specific battery replacement instructions.
- Storage: Store the remote in a dry place, away from extreme temperatures and direct sunlight.
6. Troubleshooting
- Remote not cloning:
- Ensure the original remote is a fixed code type and operates at 433.92MHz. Rolling code remotes are not compatible.
- Make sure the Yinuogo remote's history has been cleared (Section 3.1).
- Ensure the remotes are placed very close, ideally touching, during the cloning process.
- Press and hold the buttons firmly and simultaneously until the LED blinks rapidly.
- Try replacing the battery in the original remote if its signal is weak.
- Cloned remote not working:
- Verify that the cloning process was successful by checking the LED behavior during programming.
- Ensure the receiver (e.g., garage door opener) is powered on and functioning correctly.
- Check the battery in the Yinuogo remote. Replace if necessary.
- If the issue persists, try clearing the Yinuogo remote's history and reprogramming it.
- Short operating range:
- Replace the battery in the Yinuogo remote.
- Ensure there are no significant obstructions between the remote and the receiver.
- Avoid using the remote near strong sources of electromagnetic interference.
7. User Tips
- For optimal cloning success, perform the programming in a quiet area away from other radio frequency devices.
- If your original remote has multiple buttons, clone them one by one to avoid confusion.
- Always test the cloned remote immediately after programming to ensure all functions work as expected.
8. Frequently Asked Questions (FAQ)
- Q: Can this remote clone any garage door opener?
- A: No, it can only clone fixed code remotes operating at 433.92MHz. It is not compatible with rolling code remotes.
- Q: What if the LED on my Yinuogo remote doesn't blink during cloning?
- A: This usually indicates that the signal from the original remote is not being received or is too weak. Ensure the remotes are very close, the original remote has a good battery, and you are pressing the buttons correctly.
- Q: How do I know if my original remote is fixed code or rolling code?
- A: Check your original remote's manual or look for markings on the remote itself. Fixed code remotes often have DIP switches inside, while rolling code remotes typically do not. If it's a Neco TX4, it's fixed code. If it's a Neco TR4, it's rolling code and not compatible.
9. Warranty and Support
For detailed warranty information and further technical support, please refer to the official user manual provided by the manufacturer. A PDF version of the user manual is available for download:
You may also contact Yinuogo Official Store for assistance.