Shunmaii Handheld RFID/NFC Card Duplicator

Contents

Shunmaii Handheld RFID/NFC Card Duplicator

User Instruction Manual

1. Introduction

Thank you for choosing the Shunmaii Handheld RFID/NFC Card Duplicator. This device is designed for convenient reading and writing of various RFID and NFC cards, supporting both 125KHz and 13.56MHz frequencies. Please read this manual thoroughly before operating the device to ensure safe and correct usage.

Handheld RFID/NFC Card Duplicator in use with an access control system

Figure 1: Handheld RFID/NFC Card Duplicator in operation.

2. General Safety Warnings

Please read and understand all instructions in this manual before using the product. Keep these instructions for future reference and pass them on to any subsequent user.

  • This product is intended for household use only. Use it only as described in this manual.
  • Do not use the product if it is damaged in any way.
  • This product is intended for use by persons aged 18 years and above.
  • It may be used by persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge only if they have been given supervision or instruction and understand the hazards involved.
  • Do not expose the device to water, moisture, or extreme temperatures.
  • Do not attempt to open or repair the device yourself. Refer all servicing to qualified personnel.

3. Product Overview

The duplicator features a compact design with an intuitive button layout for easy operation.

Front view of the Handheld RFID/NFC Card Duplicator showing buttons and sensing area

Figure 2: Front view of the Duplicator.

3.1. Device Components

  • IC/ID Sensing Area: The designated area where cards are placed for reading or writing.
  • Indicator Light: Provides visual feedback on device status (e.g., power on, read/write success).
  • Power Button (⏻): Turns the device on or off.
  • Read Button (读 R): Initiates the card reading process.
  • Write Button (写 W): Initiates the card writing process.
  • Switch Button (换 S): Used to switch between different card types or frequencies (e.g., 125KHz ID and 13.56MHz IC).
  • Card Type Button (卡 C): May be used to select specific card types or modes.
  • Numeric Keypad (0-9): For entering specific data or card numbers if required by the operation mode.

Note on Sensing: Pay attention to adjusting the distance between the card and the sensing area for optimal performance. The ID sensing area is typically located on the back of the device.

4. Setup

4.1. Battery Installation

The device is powered by batteries (type not specified, typically AAA or similar). Locate the battery compartment on the back of the device. Insert the batteries, ensuring correct polarity (+/-). Close the battery compartment securely.

4.2. Powering On/Off

Press and hold the Power Button (⏻) for a few seconds to turn the device on. The indicator light will illuminate. To turn off, press and hold the Power Button again until the device powers down.

5. Operating Instructions

5.1. Reading a Source Card

  1. Power on the device.
  2. If necessary, use the Switch (S) or Card (C) button to select the correct frequency/card type (e.g., 125KHz for ID cards, 13.56MHz for IC cards) that matches your source card.
  3. Place the source card firmly on the IC/ID Sensing Area.
  4. Press the Read (R) button. The indicator light will flash or change color to confirm a successful read. The device may also emit an audible beep.
  5. If the read fails, adjust the card's position or distance and try again.

5.2. Writing to a Target Card

After successfully reading a source card, you can write its data to a compatible blank target card.

  1. Ensure the source card data has been successfully read (as per section 5.1).
  2. Remove the source card and place a compatible blank target card on the IC/ID Sensing Area.
  3. Press the Write (W) button. The indicator light will flash or change color to confirm a successful write. The device may also emit an audible beep.
  4. If the write fails, ensure the target card is compatible and try again.

5.3. Switching Frequencies/Card Types

Use the Switch (S) button to toggle between supported frequencies (125KHz and 13.56MHz) or card modes. Observe the device's display or indicator lights for the currently selected mode.

6. Maintenance

  • Cleaning: Wipe the device with a soft, dry cloth. Do not use liquid cleaners or abrasive materials.
  • Storage: If the device will not be used for an extended period, please remove the batteries to prevent leakage and damage. Store in a cool, dry place away from direct sunlight.
  • Battery Replacement: Replace batteries when the device's performance degrades or the indicator light becomes dim.

7. Troubleshooting

Problem Possible Cause Solution
Device does not power on Dead or incorrectly installed batteries Replace batteries; ensure correct polarity.
Card not reading/writing Incorrect card placement; wrong frequency selected; incompatible card; low battery Adjust card position; ensure card is flat on sensing area; switch frequency (S button); use compatible cards; replace batteries.
Indicator light not responding Device malfunction; low battery Replace batteries. If problem persists, contact support.

8. Specifications

Brand: Shunmaii
Supported Frequencies: 125KHz, 13.56MHz
Supported Card Types: RFID, NFC, IC, ID cards (compatible types)
Dimensions (L x W x T): 105mm (4.13in) x 45mm (1.77in) x 20mm (0.79in)
Power Source: Battery operated (type not specified, user-replaceable)
Origin: Mainland China
Certifications: CE, FC, RoHS
Dimensions of the Handheld RFID/NFC Card Duplicator

Figure 3: Device dimensions.

9. User Tips

No specific user tips were available from provided customer reviews or Q&A data for this product. General tips for optimal use include:

  • Always ensure the target card is compatible and blank before attempting to write.
  • Keep the device and cards clean and free from dust or debris.
  • Practice with non-critical cards first to familiarize yourself with the operation.

10. Warranty and Support

For any questions, technical support, or warranty inquiries regarding your Shunmaii Handheld RFID/NFC Card Duplicator, please contact the seller or retailer from whom you purchased the product. Please retain your proof of purchase for warranty claims.

Manufacturer Information:
Guangzhou Aicai Technology Co., Ltd.
Room 709, No. 68, Gangwan Road, Huangpu District, Guangzhou

© 2024 Shunmaii. All rights reserved.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.