1. Product Overview
The WS2812B Smart Pixel RGBIC LED Strip Light is an individually addressable LED strip designed for dynamic and customizable lighting effects. It features SMD5050 LEDs with an Epistar chip, offering vibrant RGBIC colors and various control options. This product is available in different IP ratings for diverse application environments.


2. Safety Information
WARNING: Risk of electric shock!
- Always isolate the mains power before proceeding with installation or removal.
- Turn off and isolate the electrical supply before connecting this fitting to building wires.
- Installation and removal must be performed by a qualified electrician.
- Never plug or unplug the device while it is powered on.
- The luminaires are intended for indoor use only, unless specified by the IP rating.
3. Setup and Installation
3.1 Components and Connections
The LED strip typically comes with a JST SM male connector attached. An LED controller (not always included) is required for operation.

3.2 Physical Installation
- Power Off: Ensure the power supply is completely disconnected before handling the LED strip.
- Measure and Plan: Determine the desired length and placement for your LED strip.
- Cutting: The strip can be cropped at designated cut marks, typically after every LED. Ensure to cut only at these marked points to maintain functionality.
- Wiring: The strip uses +5V, Data In (DI), and Ground (GND) connections. Ensure correct polarity and data line connection to your controller.
- Mounting:
- For IP30 and IP65 strips, use the integrated 3M adhesive backing to secure the strip to a clean, dry surface.
- Note that IP67 strips typically do NOT come with 3M adhesive and may require external mounting clips or channels.
- Power Connection: Connect the LED strip to a compatible DC 5V USB power source.

3.3 Waterproofing (IP Ratings)
- IP30: Non-waterproof, suitable for indoor dry environments.
- IP65: Splash-proof, suitable for indoor damp environments or areas with occasional splashes.
- IP67: Waterproof, suitable for outdoor use and can withstand temporary immersion in water. Note that IP67 versions do not come with 3M adhesive.
4. Operating Instructions
4.1 App Control
The WS2812B LED strip is designed to be controlled via a compatible smartphone application. This allows for extensive customization of colors, effects, and brightness.
- Connect: Ensure your LED strip controller is properly connected and powered on.
- Download App: Download the recommended control app (refer to your controller's instructions or product packaging for the specific app).
- Pair: Follow the app's instructions to pair your smartphone with the LED strip controller.
- Customize: Use the app's color wheel, preset modes, and brightness sliders to achieve your desired lighting effects. The app allows for precise color selection and dynamic light patterns.
4.2 Music Synchronization
Many compatible controllers and apps offer a music synchronization feature, allowing the LED strip to react to audio input, creating an immersive experience.
- Activate Music Mode: In the control app, select the music synchronization mode.
- Play Audio: Play music through your device or an external speaker. The lights will respond to the rhythm and beats.
4.3 Button Control (if applicable)
Some USB power connectors may include a physical button for basic control, such as cycling through preset colors or modes.
- Press Button: Briefly press the button on the USB connector to change the light color or mode.
- Cycle Options: Continue pressing to cycle through available options.
5. Maintenance
- Cleaning: Gently wipe the LED strip with a dry, soft cloth to remove dust. For IP65/IP67 versions, a damp cloth can be used, but ensure no water enters the connections.
- Avoid Harsh Chemicals: Do not use abrasive cleaners or harsh chemicals, as these can damage the strip's surface or LEDs.
- Inspect Connections: Periodically check all connections for secure fit and signs of wear or corrosion.
- Storage: If storing the LED strip, coil it loosely and keep it in a dry, cool place away from direct sunlight.
6. Troubleshooting
6.1 Common Issues and Solutions
| Problem | Possible Cause | Solution |
|---|---|---|
| LED strip does not light up. | No power, loose connection, faulty power supply/controller. | Check power source, ensure all connections are secure. Test with a different power supply or controller if available. |
| Part of the strip lights up in a different color or is darker. | Defective section of the strip, insufficient power, data signal issue. | Ensure adequate power supply for the entire length. Check for physical damage to the strip. If a section is defective, it may require replacement or cutting out the faulty segment. |
| Lights are flickering or unstable. | Insufficient power, loose connection, faulty controller. | Verify power supply meets the strip's requirements. Secure all connections. Try a different controller. |
| App control not working. | Controller not paired, app issues, Bluetooth/Wi-Fi interference. | Ensure controller is powered and in pairing mode. Restart app and phone. Check for interference. |
7. Specifications
| Feature | Specification |
|---|---|
| Model Number | WS2812B |
| LED Chip Model | SMD5050 |
| LED Chip Brand | Epistar |
| Voltage | 5V (DC) |
| Power Source | DC |
| Power Consumption (W/m) | 2.88W/m |
| LEDs Number/M | 30/60 |
| Luminous Flux | 60-249 |
| Average Life (hrs) | 30000 |
| Waterproof | Yes (IP30/IP65/IP67 options) |
| Strip type | SMD |
| Certification | CE |
| Occasion | LIVING ROOM |
| Power Generation | Switch |
| Is Smart Device | No (requires external controller) |
| Package Length | 13 cm |
| Package Width | 11 cm |
| Package Height | 1 cm |
| Package Weight | 0.024 kg |
8. User Tips
- Consider Connectors: The LED strip typically comes without additional connectors. It is recommended to purchase appropriate connectors (e.g., for extending or custom wiring) at the same time as the strip.
- External Controller Required: This LED strip is a standalone unit and requires an external LED controller for full functionality and customization.
- Power Supply: Ensure your 5V power supply provides sufficient amperage for the length and density of the LED strip you are using. For example, a 2A power supply might be sufficient for a 1-meter strip in a small room.
9. Frequently Asked Questions (FAQ)
Q: Will these LED strips work with a sequential turn signal controller for a car?
A: The WS2812B LED strips operate on 5V DC and are individually addressable, meaning each LED can be controlled independently. While they are technically capable of sequential effects, direct compatibility with a standard car's sequential turn signal controller is unlikely. You would typically need a dedicated WS2812B controller that can be integrated into a car's electrical system and programmed for the desired sequential turn signal patterns. Consult with an automotive electrician or specialist for such custom installations.
10. Warranty and Support
For detailed warranty information and customer support, please refer to the seller's policies or contact Parkson Official Store directly. A user manual in PDF format is available for further reference: