Zemismart SPM02-DZT2

Contents

Zemismart Zigbee Smart Energy Meter SPM02-DZT2 User Manual

1. Introduction

The Zemismart SPM02-DZT2 Smart Energy Sensor is a real-time electrical monitoring device equipped with wireless Zigbee communication. Designed for flexible installation, it functions as a smart accessory for protective and control devices. It accurately monitors key electrical parameters, sends alarm messages, and can be integrated into automation routines with other smart devices.

Zemismart Zigbee Smart Energy Meter with 3-phase, 4-wire connection diagram.

Image: Zemismart Zigbee Smart Energy Meter with 3-phase, 4-wire connection diagram.

2. Safety Information

2.1 Hazard of Electric Shock, Explosion, or Arc Flash

  • Turn off all power supply sources before installing and during maintenance of this equipment.
  • Do not use an SPM02 sensor for voltage testing purposes. A dedicated voltage tester must be used instead.

2.2 Fire Hazard

  • SPM02 sensors must be associated with an easily accessible upstream protection and circuit-breaker system.
  • The terminals of the voltage measuring cables must be adjusted according to the equipment being monitored. It is the responsibility of qualified professionals to provide such cable terminals.

2.3 Risk of Damaging SPM02 Sensors

  • Comply with the neutral phase wiring: Brown (X), Black (Y), Grey (Z), Blue (Neutral).
  • Disconnect SPM02 sensors before performing the dielectric withstand test.
  • SPM02 sensors can only be installed upstream if associated with a contactor, variable frequency drive, or motor starter.
  • Limit insulation measurements up to 500 VDC.

Warning: Failure to follow these instructions can result in death, serious injury, or equipment damage.

3. Product Overview

The SPM02-DZT2 is designed for compact installation within electrical panels or distribution boards.

Space-saving design of the energy meter, showing its compact dimensions (53mm x 21mm) and installation within an electrical distribution board.

Image: Space-saving design of the energy meter, showing its compact dimensions (53mm x 21mm) and installation within an electrical distribution board.

3.1 Components

Product introduction diagram, highlighting key components: Through-holes (X, Y, Z), Reset button, Indicator light, and the positive energy flow direction from Source to Load.

Image: Product introduction diagram, highlighting key components.

  • Through-holes (X, Y, Z): For current sensing.
  • Reset button: Used for pairing and resetting the device.
  • Indicator light: Provides status feedback.
  • Wiring Terminals: For N (Blue), Z (Grey), Y (Black), and X (Brown) connections.
  • Energy Flow Direction: Indicated from Source to Load.

4. Specifications

AttributeValue
Product NameSmart Energy Sensor
ModelSPM02-DZT2
Communication MethodZigbee
Power SourceAC
Rated Voltage U3N-120-240V / 200-415V 50/60Hz
Max. Current63A
Over-voltage CategoryIII
Rated Insulating Voltage U400V
Rated Impulse Withstand Voltage U4kV
Pollution Degree3
Protection DegreeIP20
Rated Operating Temperature-25°C to 60°C
Power Consumption (Normal)0.7 W
Power Consumption (Pairing)1.4 W
Energy Measurement Accuracy1%
Battery IncludedNo
Inbox AdaptorNo
OriginMainland China
CertificationCE

5. Setup

5.1 Pre-installation Checks

  • SPM02 sensors must only be installed and maintained by qualified professionals.
  • Do not install SPM02 sensors if any damage is observed during unpacking.
  • Install SPM02 sensors inside electrical panels or switchboards, behind a door or plate, to ensure they are inaccessible to unauthorized persons.
  • Electrical panels must comply with IEC 61439-1 and be installed according to IEC 61140.
  • Adhere to all relevant local, regional, and national regulations during installation and use.

5.2 Wiring Diagrams

The sensor powers itself and measures voltage via the cables for X, Y, Z, and N connections. The energy flowing in the same direction as the current flow arrow printed on the sensor housing is counted as forward energy.

Multi-language quick installation guide and safety warnings, including detailed wiring diagrams (Scheme A and B) and specifications.

Image: Detailed wiring diagrams (Scheme A and B) for 3P+N flexible installation. Consult this image for specific wiring configurations for Through-hole X, Y, Z, and N connections.

5.3 App Installation and Gateway Setup

  1. Before activating the SPM02 sensor, ensure you have the latest version of the Smart Life app downloaded and installed on your mobile device.
  2. If your device is the Zigbee version, properly install a Tuya Smart Zigbee gateway beforehand.

5.4 Pairing Instructions

  1. Connect your mobile phone to the wireless network.
  2. Open the Smart Life app, tap "Home", and then tap "+" in the top right corner to enter the "Add Device" page.
  3. Press the reset button on the SPM02-DZT2 for 3-5 seconds until the LED quickly flashes. This indicates it has entered pairing mode. If you have previously removed the device from the app, it will automatically enter pairing mode.
  4. The app will scan for smart devices to be configured. Follow the app prompts once the SPM02 sensor appears to complete the pairing process.

6. Operating

6.1 Real-time Monitoring

Once connected, the SPM02-DZT2 allows for real-time monitoring of electrical parameters via the Tuya Smart Life app.

Tuya APP real-time monitoring interface, displaying current, active power, and voltage readings for X, Y, and Z phases.

Image: Tuya APP real-time monitoring interface, displaying current, active power, and voltage readings for X, Y, and Z phases.

In the Tuya APP control page, swipe right to display the RMS value of the Y-phase and Z-phase current. The device offers high-precision energy measurement within a 1% tolerance.

Accurate energy measurement display in the Tuya APP, showing total forward active energy, real-time voltage, current, and power, with a note on 1% tolerance.

Image: Accurate energy measurement display in the Tuya APP, showing total forward active energy, real-time voltage, current, and power.

6.2 Alarm Messages

The Tuya APP will send alarm messages when the measurement data exceeds predefined warning values.

Tuya APP alarm messages, illustrating various alerts such as abnormal temperature, over current, unbalanced load, over voltage, and under voltage.

Image: Tuya APP alarm messages, illustrating various alerts.

  • Abnormal temperature alarm
  • Over current alarm
  • Unbalanced-load alarm
  • Over voltage alarm
  • Under voltage alarm

6.3 Indicator Light Description

Light StatusDescription
ONNormal operation, connected to cloud.
Flashing at 2HzIn pairing mode.
Flashing at 0.5HzPaired, searching for cloud connection.
Flashing at 1HzWireless communication failed.
Flashing at 0.25HzSelf-checking failed.

7. Maintenance

  • Do not disassemble, modify, or short-circuit the product. This may cause electric shock, fire, or electrical damage.
  • The SPM02-DZT2 is an electronic product; avoid strong impacts, collisions, or dropping the product.
  • Strictly avoid exposing the product to extreme heat, cold, or humidity.
  • Store the product in a safe place, out of reach of children, to prevent hazards.

8. Troubleshooting

  • Device not pairing: Press the reset button for 3-5 seconds until the LED flashes quickly to enter pairing mode. If the device was previously removed from the app, it should automatically enter pairing mode.
  • Product connected to network but not cloud: If the product successfully connects to a wireless network but cannot establish a connection to the cloud server, check the indicator light status (Flashing at 0.5Hz).
  • Cloud communication failed: If communication with the cloud fails (indicator light flashing at 1Hz), verify that the supply voltage is not too low.
  • General issues: Try restarting the device by disconnecting its power supply, then reconnecting it, and attempting to pair it again.

9. User Tips

  • Professional Installation: Many users recommend having an electrician install the device to ensure proper and safe setup.
  • Tuya App Compatibility: The energy meter is confirmed to work with the Tuya app using the Zigbee protocol.
  • Reliability: Users generally find the product reliable for its intended purpose.

10. Warranty and Support

For detailed information regarding warranty, technical support, or further instructions, please refer to the official user manual PDF available at Zemismart SPM02-DZT2 User Manual (PDF).

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.