Aigo AR12PRO

Contents

Aigo AR12PRO Computer Case Fan User Manual

Model: AR12PRO

Introduction

This manual provides instructions for the installation, operation, maintenance, and troubleshooting of the Aigo AR12PRO 120mm RGB PWM computer case fan. Please read this manual thoroughly before installation and use to ensure proper functionality and safety.

Package Contents

The Aigo AR12PRO fan package typically includes the following components:

  • AR12PRO Fan (quantity varies by package)
  • Mounting Screws (4 per fan)
  • Connection Cables (4PIN PWM Male/Female, 5v A-RGB 3pin Male/Female)
  • (Optional) APC1 Controller or Magnetic Light Bar, depending on the specific product variant purchased.
Diagram showing AR12PRO fan accessories, size, fan interfaces, and connection steps.
Figure 1: AR12PRO Fan Accessories, Dimensions, and Connection Diagram. This diagram illustrates the fan, mounting screws, fan interfaces (4PIN PWM Male/Female, 5v A-RGB 3pin Male/Female), and connection steps for both power and ARGB.
Diagram of a magnetic light bar with dimensions and 3PIN 5V connector.
Figure 2: Optional Magnetic Light Bar. This image shows the magnetic light bar, its length (372 MM), power cord length (700 MM), and the 3PIN 5V connector.

Installation and Setup

1. Physical Installation

  1. Identify the desired mounting location(s) for the fan(s) within your computer case or on your radiator.
  2. Position the fan in the desired orientation (intake or exhaust).
  3. Secure the fan using the provided mounting screws. Ensure the screws are tightened firmly but do not overtighten to avoid damaging the fan frame.

2. Cable Connections

The AR12PRO fan uses two main types of connections: a 4-pin PWM connector for fan speed control and a 3-pin 5V ARGB connector for lighting control.

  • 4PIN PWM Connection:
    1. Locate the 4PIN PWM Male connector on the fan cable (line length: 460±10mm). Connect this to an available 4-pin fan header on your motherboard or fan controller.
    2. If connecting multiple fans in series, use the 4PIN PWM Female connector (attached cable length: 85±10mm) from the first fan to connect to the next fan's 4PIN PWM Male connector.
  • 5v A-RGB Connection:
    1. Locate the 5v A-RGB 3pin Male connector on the fan cable (line length: 500±10mm). Connect this to an available 5V 3-pin ARGB header on your motherboard or ARGB controller.
    2. If connecting multiple fans in series, use the 5v A-RGB 3pin Female connector (attached cable length: 60±10mm) from the first fan to connect to the next fan's 5v A-RGB 3pin Male connector.

Tandem Connection: The fans are designed for series connection, where the former fan connects to the latter fan, creating a cycle overlap for both PWM and ARGB signals. This allows for synchronized control of multiple fans from a single header.

Aigo AR12PRO fan box with compatibility logos for ASUS Aura Sync, Gigabyte RGB Fusion 2.0, MSI Mystic Light Sync, and ASRock Polychrome RGB.
Figure 3: AR12PRO Packaging highlighting ARGB software compatibility.

Operation

Fan Speed Control (PWM)

The AR12PRO fans support Pulse Width Modulation (PWM) for precise speed control. Connect the 4-pin PWM cable to a compatible motherboard header. Fan speed can then be adjusted via your motherboard's BIOS settings or through motherboard-specific software utilities.

ARGB Lighting Control

The Addressable RGB (ARGB) lighting can be controlled in several ways:

  • Motherboard Software: If connected to a 5V 3-pin ARGB header on a compatible motherboard, you can control the lighting effects using software such as ASUS Aura Sync, GIGABYTE RGB Fusion 2.0, MSI Mystic Light Sync, or ASRock Polychrome RGB.
  • Dedicated ARGB Controller: If your motherboard does not have a 5V 3-pin ARGB header, or if you prefer external control, a dedicated ARGB controller (e.g., APC1 Controller, if included or purchased separately) can be used. Some controllers offer remote control functionality.
  • Case Reset Button (Limited Functionality): In some setups, if an ARGB controller is connected to the case's reset button, it may allow for cycling through basic lighting modes.

Maintenance

Regular maintenance helps ensure optimal performance and longevity of your Aigo AR12PRO fans.

  • Cleaning: Periodically clean the fan blades and frame to remove dust buildup. Use compressed air or a soft brush. Ensure the fan is powered off and disconnected from the system before cleaning.
  • Inspection: Check for any obstructions around the fan blades or unusual noises during operation.
  • Cable Management: Ensure all cables are neatly routed and not interfering with fan operation or airflow.

Troubleshooting

Fan Not Spinning / Low Speed

  • Check the 4-pin PWM connection to the motherboard or controller. Ensure it is securely seated.
  • Verify fan speed settings in your motherboard's BIOS or software.
  • Ensure the power supply is providing adequate power to the fan headers.

ARGB Lights Not Working / Incorrect Colors

  • Confirm the 5V 3-pin ARGB connector is correctly plugged into a compatible ARGB header (not a 12V RGB header, which can damage the LEDs).
  • Check the ARGB control software (motherboard or dedicated controller) for correct settings and synchronization.
  • If using a controller, ensure it is powered correctly and functioning.
  • If multiple fans are daisy-chained, check connections between each fan.

Excessive Noise

  • Ensure mounting screws are tight but not overtightened. Loose screws can cause vibration.
  • Check for any cables or obstructions touching the fan blades.
  • Dust buildup can sometimes cause imbalance and noise; clean the fan.

Specifications

FeatureSpecification
Model NumberAR12PRO
Fan Size120 MM (120mm x 120mm x 25mm)
Fan Speed800 - 1900 RPM
Noise Level28 dBA
Air Volume74 CFM
Fan Life100,000 hours
Bearing TypeFluid Bearing
Power Interface4PIN (PWM), 5v-3pin ARGB
Voltage12V
Power (W)5.1W
Blade Quantity9
Lines4 LINES
Used ForCase, Radiator
CertificationCE, FCC, RoHS
OriginMainland China
Diagram showing the dimensions of the Aigo AR12PRO fan: 120mm width, 120mm height, and 25mm thickness.
Figure 4: AR12PRO Fan Dimensions.

Package Dimensions

  • Length: 15 cm
  • Width: 13 cm
  • Height: 8 cm
  • Weight: 0.466 kg

User Tips

  • Mounting Screws: While installing, ensure mounting screws are snug but avoid overtightening. Some users have noted that screws can feel a bit loose, so a firm but gentle approach is recommended.
  • RGB Control: If your motherboard lacks a 5V 3-pin ARGB header or you prefer more direct control, consider purchasing a dedicated ARGB controller. This allows for remote control and more versatile lighting effects.
  • Performance: These fans are known for being quiet while providing sufficient airflow (high CFM), making them suitable for both case and radiator cooling.
  • Longevity: Aigo fans, including the AR12PRO series, have a reputation for good durability and long operational lifespans.

Frequently Asked Questions (FAQ)

Q: How many fans are included in a package?

A: The quantity of fans included varies by the specific product variant (SKU) purchased. Some packages may contain a single fan, while others are multi-fan sets (e.g., 3-fan or 5-fan sets). Please check the product description of your specific purchase for details.

Q: Is an ARGB controller included?

A: An ARGB controller may or may not be included, depending on the specific product variant (SKU) purchased. Some multi-fan sets often include a controller, while single fans typically do not. If you require a controller for lighting effects, please verify if it's part of your chosen package or consider purchasing one separately.

Warranty and Support

For detailed warranty information and technical support, please refer to the official Aigo website or contact your retailer. A user manual in PDF format may also be available for download from the seller's product page or the manufacturer's support section.

A user manual (PDF) is available for this item. You can typically find it linked on the product's detail page or by searching the manufacturer's support resources.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.