Solar COB Neon Strip Lights User Manual

1. Important Safety Information

Please read all safety instructions carefully before using the product. Failure to follow these instructions may result in electric shock, fire, or serious injury.

• This product is designed for outdoor decoration and lighting.
• Ensure the solar panel is installed in a sunny environment to maximize charging efficiency.
• Do not install the product in environments where street lamps are used, as this may interfere with the light sensor and operation.
• Do not attempt to dismantle or modify the product if you are not a professional. Product failures due to non-quality problems (e.g., improper dismantling) are not covered by warranty.
• Keep out of reach of children under 6 years of age.
• The product is IP68 waterproof, suitable for outdoor use, but avoid prolonged submersion.

2. Package Contents

Verify that all components are present in your package:

• Solar Panel Unit (with integrated control panel)
• COB Neon LED Strip (selected length)
• Remote Control
• Ground Stake (for solar panel installation)
• Wall Mounting Accessories (screws, expansion pipes)
• USB Charging Cable

3. Setup and Installation

3.1 Initial Preparation

1. Remove Battery Separator: Before first use, open the remote control battery compartment and remove any plastic battery separator tab.
2. Initial Charge: For optimal performance, fully charge the solar panel unit before the first use. Place the solar panel in direct sunlight for 4-5 hours, or use the provided USB cable to charge the unit.

3.2 Assembling the Solar Panel Unit

1. Attach the ground stake components together by twisting them.
2. Insert the assembled ground stake into the designated slot on the solar panel unit.
3. Alternatively, use the wall mounting bracket and screws to secure the solar panel unit to a wall.

Figure 1: Product overview with solar panel and strip.

3.3 Connecting the LED Strip

1. Locate the output port on the solar panel unit.
2. Connect the COB Neon LED Strip's connector to the output port. Ensure a secure, watertight connection by tightening the cap.

3.4 Placement

Position the solar panel in an area that receives maximum direct sunlight throughout the day. Avoid shaded areas or locations near other light sources (like street lamps) that might interfere with the automatic dusk-to-dawn sensor.

Figure 2: Solar panel charging in direct sunlight.

4. Operating Instructions

4.1 Control Panel

The solar panel unit features a control panel with indicators and buttons:

• OUT: Output indicator light.
• MODE: Mode display.
• MODE Button: Short press to switch between lighting modes. Long press to adjust brightness.
• ON/OFF Button: Power switch. This switch must be turned ON for the first use and for the unit to operate.
• Charging Indicators: LEDs indicating battery charge level (25%, 50%, 75%, 100%).
• USB-C Port: For alternative charging.

Figure 3: Solar unit control panel.

4.2 Remote Control Functions

The remote control allows for convenient operation from a distance of 5-7 meters.

Figure 4: Remote Control Description.

• NO (Power Button): Turns the lights ON.
• OFF (Shut off): Turns the lights OFF.
• RST (Reset Button): Resets the lighting mode.
• Mode Buttons (1-8): Selects different lighting modes. Mode 1 is 100% brightness with no timing.
• Brightness Decrease (-): Reduces brightness.
• Brightness Plus (+): Increases brightness.
• Timing Buttons (3H, 6H, 8H): Sets the lights to stay on for 3, 6, or 8 hours respectively.
• TIME OFF: Deactivates the timer function, allowing the lights to stay on until the battery runs out or dawn.
• Dimming (20%, 60%, 100%): Directly sets the brightness level.
• Speed Adjustment (+/-): Adjusts the speed of dynamic lighting modes (if applicable).

5. Maintenance

• Clean Solar Panel: Regularly wipe the solar panel surface with a soft, damp cloth to remove dust, dirt, or debris. A clean panel ensures maximum charging efficiency.
• Check Connections: Periodically inspect all connections, especially the one between the LED strip and the solar unit, to ensure they are secure and free from corrosion.
• Battery Care: While the unit is designed for outdoor use, extreme temperatures can affect battery life. If storing for extended periods, ensure the battery is partially charged.
• Avoid Disassembly: Do not attempt to open the solar panel unit or the LED strip. Unauthorized disassembly may damage the product and void the warranty.

6. Troubleshooting

6.1 Lights Not Turning On or Low Intensity

• Check Power Switch: Ensure the ON/OFF button on the solar unit is pressed to the 'ON' position.
• Battery Charge: Verify the battery charge indicators on the solar unit. If low, ensure the solar panel is receiving adequate direct sunlight for 4-5 hours, or charge via the USB cable.
• Connections: Inspect the connection between the LED strip and the solar unit. Ensure it is fully inserted and tightened.
• Internal Wiring (Caution): Some users have reported issues with loose internal battery connections. While disassembly is not recommended and may void warranty, if you are experienced, you might check for loose wires inside the solar unit.
• Environmental Interference: Ensure the solar panel is not located near other strong light sources (e.g., street lamps) at night, as this can prevent the lights from activating automatically.

6.2 Remote Control Not Working

• Battery: Check the remote control battery and ensure the plastic separator tab has been removed. Replace if necessary.
• Distance: Ensure you are within the 5-7 meter operating range of the remote.
• Line of Sight: Ensure there are no obstructions between the remote and the solar unit's sensor.

6.3 Lights Always On / Twilight Sensor Malfunction

• External Light Sources: The solar unit's sensor detects ambient light. If installed near streetlights or other strong artificial light sources, it may not correctly detect darkness, causing the lights to remain off or on at inappropriate times. Relocate the solar panel to a darker area.

7. User Tips

• Custom Lengths: The COB Neon LED strip can be cut every 5cm. Look for the visible cutting line through the light for precise customization.
• Optimal Placement: For best performance, ensure the solar panel is positioned to receive at least 6-8 hours of direct sunlight daily.
• Remote Convenience: Utilize the remote control for easy adjustment of modes, brightness, and timing without needing to access the solar unit directly.
• Battery Check: If you experience inconsistent performance, check the battery charge indicators on the solar unit.

Figure 5: LED strip with visible cutting line.

8. Specifications

Figure 6: Solar panel and battery capacity comparison.

Figure 7: Internal view of solar unit with batteries.

Figure 8: Close-up of IMR18650 batteries.

9. Warranty and Support

This product comes with a 3-year warranty. The warranty covers manufacturing defects but does not cover product failures due to non-quality problems, such as improper installation, unauthorized disassembly, or misuse.

For additional item guides and documents, including a detailed user manual in PDF format, please refer to the official product page or contact customer support. The PDF manual can be found at: User manual (PDF)