YAMOTC YM0104479, YM0104483, YM0104484, YM0104485

Contents

Adjustable Extension Windscreen Windshield Spoiler Deflector User Manual

Model: YM0104479, YM0104483, YM0104484, YM0104485

1. Important Safety Information

Read all instructions before use. Failure to follow these instructions may result in damage to the product or personal injury.

⚠️ Warning: Improper use/installation may cause accidents. Abide by:

  1. Install only on compatible, intact motorcycles.
  2. Ensure motorcycle stability during installation; check firmness before riding.
  3. No vision obstruction.
  4. Stop use if damaged/loose.
  5. Wear helmet (windshield provides no impact protection).
  6. User bears responsibility for non-compliant use.

2. Setup Instructions

This section details the steps for correctly installing your adjustable windscreen extension.

2.1. Attaching Clamps to Extension

  1. Secure the two adjustable clamps to the bottom slots of the windshield extension.
  2. Tighten the clamp screws by hand to keep them in place, leaving them loose enough for adjustment.

2.2. Mounting the Extension

  1. Position the extension over your existing windshield, aligning the clamps with the upper edge of the original windshield.
  2. Adjust the clamps to ensure a firm, centered fit.

2.3. Assembly Diagrams

Refer to the diagrams below for detailed assembly of the brackets.

Exploded view assembly diagram for V1 and V2/V3 brackets, showing screws, washers, and bracket components.
Figure 1: Exploded view assembly diagram for V1 and V2/V3 brackets.
Diagram showing components for V1 and V2/V3 brackets, highlighting differences in design.
Figure 2: Bracket component comparison for V1 and V2/V3 versions.

2.4. Visual Installation Guide

Watch the video and review the images for a visual guide on installation and adjustment.

Video 1: Product demonstration showing height and angle adjustment on a motorcycle.

Six-panel image showing step-by-step installation and adjustment of the windscreen extension on a motorcycle.
Figure 3: Step-by-step visual guide for installation and adjustment.

3. Operating Instructions

Once installed, the windscreen extension can be adjusted for optimal performance.

3.1. Adjusting Height & Securing

  1. Slide the extension up or down along the clamps to reach your desired height. The double hinges provide a total up/down vertical range of up to +/- 110mm.
  2. Tighten all clamp screws securely to prevent movement while riding. Do not over-tighten, as this may damage the windshield or clamps.

3.2. Final Check

  1. Gently push on the extension to confirm it is stable and free of movement.
  2. Double-check that all screws are tightened and the extension is aligned evenly.

4. Maintenance

Proper care will ensure the longevity and clarity of your windscreen extension.

  • Clean with a soft cloth and water only.
  • Do not use corrosive cleaners, as they can damage the PC glass and brackets.

5. Troubleshooting

If you encounter issues, refer to these common solutions.

  • Loose Fit: Ensure all clamp screws are securely tightened. If the fit remains loose, consider adding thin rubber strips or padding between the clamps and your original windshield for a tighter seal.
  • Excessive Vibration/Noise: Re-adjust the height and angle of the extension. Small changes can significantly reduce wind noise and buffeting. Ensure the extension is firmly secured and not vibrating independently.
  • Damage/Instability: If the extension becomes damaged or excessively loose during use, stop using it immediately. Inspect all components for cracks or wear.
  • Vision Obstruction: Ensure the extension does not obstruct your view of the road or instruments. Adjust its position or angle if necessary.

6. Specifications

FeatureDescription
Product NameAdjustable Extension Windscreen Windshield Spoiler Deflector
Model NumbersYM0104479, YM0104483, YM0104479, YM0104484, YM0104479, YM0104485
MaterialPC Plastic (Windscreen), ABS Plastic (Bracket)
Item TypeWindscreens/Wind Deflectors
Color OptionsTransparent, Smoked
FitmentUniversal (fits most motorcycles, sport bikes, street bikes, scooters with existing windshield)
AdjustabilityHeight (up to +/- 110mm vertical range), Angle
Dimensions (V1 Small)Width: 280mm, Height: 120mm

6.1. Version Differences

  • V1: Standard PC glass + ABS bracket.
  • V2: Standard PC glass + upgraded ABS bracket.
  • NEW V3: High-definition glass + reinforced/upgraded ABS bracket.
Comparison of V1 and V2 bracket designs, highlighting the upgraded ABS bracket in V2.
Figure 4: Comparison of V1 and V2 bracket designs.
Features of NEW V3, including reinforced bracket and high-definition glass.
Figure 5: Features of the NEW V3 version.
Dimensions for the V1 small model, showing 280mm width and 120mm height.
Figure 6: Dimensions for V1 Small model.

7. User Tips

Tips from other users to enhance your experience:

  • Secure Mounting: Always ensure the product is firmly locked onto your original windshield before riding, especially at higher speeds.
  • Custom Fit: If you experience a slightly loose fit, some users have found success by adding thin rubber strips or padding to the clamps for a tighter, more secure seal.
  • Optimize Comfort: Experiment with different height and angle adjustments. Small changes can significantly reduce wind noise and buffeting, leading to a more comfortable and relaxed ride.

8. Warranty & Support

For warranty information, returns, or technical support, please contact your original seller or the manufacturer directly.

8.1. Manufacturer Information

  • Company Name: Guangzhou Amo Trading Co Ltd
  • Full Address: Room 3178, 3rd Floor, Building 13, 827 Xicha Road, Baiyun District, Guangzhou City
  • Email: yamotc@yeah.net
  • Zip Code: 510000
  • Telephone: 86-15820314526

8.2. EU Authorized Representative

  • Company Name: SUCCESS COURIER SL
  • Full Address: ES-CALLE RIO TORMES NUM. 1, PLANTA 1, DERECHA, OFICINA 3, Fuenlabrada, Madrid, 28947 Spain
  • Email: successservice2@hotmail.com
  • Zip Code: 28947
  • Telephone: 34-910602659

8.3. Compliance Information

This product complies with the following EU regulations and harmonized standards, ensuring compliance with EU road traffic safety requirements after installation:

  • Regulation (EU) 2016/425 of the European Parliament and of the Council (Personal Protective Equipment Regulation), Date of Application: April 21, 2018.
  • Harmonized Standard: EN 1952:2017 (Motorcycle accessories - Windshields and wind deflectors - Safety requirements and test methods), Date of Publication: September 1, 2017.
  • Harmonized Standard: EN ISO 3537:2019 (Road vehicles - Safety glazing materials), Date of Publication: March 15, 2019.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.