Introduction
This manual provides detailed instructions for the QIACHIP KR2202 433Mhz 2-channel relay receiver and its accompanying remote controls. This system is designed for universal control of various AC and DC devices, including lighting, electric doors, automated curtains, and garage doors. Please read this manual thoroughly before installation and operation.
Safety Information
- WARNING: Always disconnect power before installing or servicing the device to prevent electric shock.
- Ensure all wiring is performed by a qualified professional and complies with local electrical codes.
- Do not expose the receiver or remote controls to moisture or extreme temperatures.
- Keep out of reach of children.
Product Overview
Components
The QIACHIP KR2202 system typically includes:
- KR2202 2-Channel Receiver Module
- Remote Control Transmitters (2-button or 4-button variants)
Receiver (KR2202) Features
The receiver module (KR2202) features:
- Antenna: For receiving RF signals from the remote control.
- Indicator Light: Provides visual feedback during operation and learning.
- Learning Button: Used to pair remote controls and set operating modes.
- Output Terminals: Normally Open (NO), Normally Closed (NC), and Common (COM) for connecting devices.
- Input Terminals: N (Neutral) and L (Live) for power supply (AC 85V-250V).

Image: QIACHIP KR2202 receiver module and two 2-button remote controls.

Image: Detailed diagram of the KR2202 receiver showing the antenna, indicator light, learning button, and terminal connections (NO, NC, COM, IN L, IN N).
Remote Control Features
The remote control transmitters typically feature:
- Buttons: Labeled A, B (and sometimes C, D) for controlling the receiver.
- Indicator Light: Illuminates when a button is pressed.
- Battery: CR2032 button battery (3V).

Image: Diagram of a 2-button remote control transmitter, highlighting the indicator light, buttons, and CR2032 battery.
Technical Specifications
| Feature | Specification |
|---|---|
| Input Power | AC 85V-250V |
| RF Frequency | 433.92MHz |
| Quiescent Current | 8.5mA |
| Max Load | 2200W (10A) |
| Receiver Sensitivity | -108dBM |
| Operation Modes | Momentary, Toggle, Latched |
| Matching Mode | Intelligent Learning Code |
| Support Remote Type | Learning code (EV1527) |
| Output | NO, NC, COM |
| Working Temperature | -10 ~ +80°C |
| PCB Dimension | 68*47mm |
| Control Distance | More than 50 meters in open area |
| Maximum Remote Storage | 25 Remote Controls |
Setup and Installation
WARNING: Always disconnect power before performing any wiring to prevent electric shock.
Wiring Diagrams
The KR2202 receiver can be wired to control various AC and DC devices. Ensure correct polarity and voltage.
AC Motor Wiring

Image: Wiring diagram for connecting the KR2202 receiver to an AC motor (e.g., for garage doors or automated curtains). Shows connections for Up, Down, N, and L from an AC 85V-250V source.
DC Motor Wiring

Image: Wiring diagram for connecting the KR2202 receiver to a DC motor. Shows connections for positive (+), negative (-), N, and L from an AC 85V-250V source, with the DC motor operating at 12V, 24V, or 36V.
AC Device Wiring (e.g., Lights)

Image: Wiring diagram for connecting the KR2202 receiver to AC devices like lights. Shows connections for N and L from an AC 85V-250V source to the receiver, and then to the AC lights via the relay outputs.
DC Device Wiring (e.g., Lights)

Image: Wiring diagram for connecting the KR2202 receiver to DC devices like lights. Shows connections for N and L from an AC 85V-250V source to the receiver, and then to the DC lights (1V-250V) via the relay outputs.
Pairing Remote Controls (Learning Modes)
The receiver supports three operating modes: Momentary, Toggle, and Latched. You can pair up to 25 remote controls.
Reset Method (Clear all matched remotes)
- Press the receiver's learning button 8 times.
- The receiver's LED indicator will flash, indicating that all remote control data in its memory has been cleared. The reset function is complete.
Set Momentary Mode
In Momentary mode, the relay is active only while the remote button is pressed.
- Press the receiver's learning button once. Wait for the LED on the receiver to turn off and enter the setting state.
- Press button A on the remote control once. The LED on the receiver will flash and then turn off.
- Press button B on the same remote control. The indicator will flash and then light up. Momentary mode is now set.
Set Toggle Mode
In Toggle mode, pressing the remote button once turns the relay ON, and pressing it again turns it OFF.
- Press the receiver's learning button twice. Wait for the LED on the receiver to turn off and enter the setting state.
- Press button A on the remote control once. The LED on the receiver will flash and then turn off.
- Press button B on the same remote control. The indicator will flash and then light up. Toggle mode is now set.
Set Latched Mode
In Latched mode, pressing one remote button turns the relay ON, and pressing another remote button turns it OFF.
- Press the receiver's learning button three times. Wait for the LED on the receiver to turn off and enter the setting state.
- Press button A on the remote control once. The LED on the receiver will flash and then turn off.
- Press button B on the same remote control. The indicator will flash and then light up. Latched mode is now set.
Operating Instructions
Once the desired mode is set, operate the device using the paired remote control:
- Momentary Mode: Press and hold button A to activate the relay. Release button A to deactivate.
- Toggle Mode: Press button A once to activate the relay. Press button A again to deactivate.
- Latched Mode: Press button A to activate the relay. Press button B to deactivate the relay.
Video Demonstration
Video: A demonstration of the Momentary, Toggle, and Latched operating modes for the QIACHIP KR2202 receiver controlling 220V AC lamps.
Maintenance
Remote Control Battery Replacement
The remote control uses a CR2032 button battery. If the remote's indicator light does not illuminate or its range decreases, replace the battery.
- Open the remote control casing (usually by gently prying it open with a small flat-head screwdriver).
- Remove the old CR2032 battery.
- Insert a new CR2032 battery with the positive (+) side facing up.
- Close the remote control casing securely.
Cleaning
Wipe the receiver and remote controls with a dry, soft cloth. Do not use liquid cleaners or solvents.
Troubleshooting
- Device not responding to remote control:
- Ensure the receiver is powered correctly (AC 85V-250V).
- Check the remote control battery. Replace if necessary.
- Verify that the remote control is correctly paired to the receiver in the desired operating mode. Perform the learning procedure again if unsure.
- Ensure the remote control is within the effective range (more than 50 meters in open area).
- Check for obstructions or strong RF interference.
- Only one relay working (in a 2-channel setup):
- This might indicate an issue with the pairing process for the second channel or a faulty relay. Re-pair the remote, ensuring both buttons (A and B) are pressed during the learning sequence for Momentary/Toggle/Latched modes as instructed.
- Receiver LED not flashing during reset/learning:
- Ensure the learning button is pressed correctly and for the specified number of times.
- Verify power supply to the receiver.
- Device turns ON but not OFF (or vice-versa):
- This suggests an incorrect operating mode setting. Re-program the receiver to the desired Momentary, Toggle, or Latched mode.
User Tips
- Easy Setup: Many users find the setup and installation straightforward, especially for basic lighting control.
- Versatile Pairing: The receiver can be paired with multiple remote controls (up to 25), allowing for flexible control options.
- Customizable Control: Experiment with Momentary, Toggle, and Latched modes to find the best fit for your application (e.g., momentary for garage doors, toggle for lights).
- Check Wiring: Always double-check your wiring against the provided diagrams before applying power.
Frequently Asked Questions (FAQ)
- Q: Can I use multiple remote controls with one receiver?
A: Yes, the receiver can store up to 25 remote controls. - Q: Is this product suitable for garage door motors?
A: Yes, it can be used for garage door motors, often utilizing the Momentary mode for open/close functions. Refer to the AC Motor Wiring Diagram. - Q: What if I only received the remote controls and not the receiver?
A: Please contact the seller or customer support for assistance with missing components. - Q: Where can I find more detailed instructions or support?
A: A user manual in PDF format is available for download. (Reference: User manual (PDF))
Warranty and Support
For detailed warranty information and customer support, please refer to the official product documentation or contact the manufacturer directly. A comprehensive user manual in PDF format is available for download at: https://manuals.plus/m/f53a1ba7e40dcc7c9154750cb2586c5fbd0b5dd34f970ed2af70f2d18b7a5aad.