STEPPERONLINE LE-400-24/36/48

Contents

STEPPERONLINE 400W Switching Power Supply User Manual

Model: LE-400-24/36/48

Brand: STEPPERONLINE

1. Introduction

This manual provides instructions for the safe and efficient use of the STEPPERONLINE 400W Switching Power Supply. This power supply is designed for various applications, including powering stepper motors and CNC router kits, offering selectable input voltages (115V/230V) and available output voltages of 24V, 36V, or 48V depending on the specific model variant.

Please read this manual thoroughly before installation and operation to ensure proper functionality and to prevent damage to the unit or connected equipment.

STEPPERONLINE 400W Switching Power Supply front view with terminals and adjustment potentiometer
Figure 1: Front view of the STEPPERONLINE 400W Switching Power Supply, showing output terminals and voltage adjustment.

2. Setup and Installation

2.1 Unpacking and Inspection

Carefully unpack the power supply and inspect it for any signs of damage during transit. If any damage is found, do not proceed with installation and contact your supplier.

2.2 Input Voltage Selection

The power supply features a selectable input voltage switch (115V/230V). Before connecting power, ensure the switch is set to match your local mains voltage. Incorrect voltage selection can cause severe damage to the unit.

Side view of the power supply showing the 115V/230V input voltage selector switch
Figure 2: Side view illustrating the 115V/230V input voltage selector switch. Ensure it is correctly set before powering on.

2.3 Wiring Connections

Connect the power supply according to the following terminal assignments. Ensure all connections are secure and properly insulated.

  • L, N: AC Input (Live and Neutral)
  • ⌂: Ground connection
  • -V: DC Output Negative
  • +V: DC Output Positive
Angled view of the power supply showing input and output terminals
Figure 3: Angled view of the power supply, highlighting the input (L, N, Ground) and output (+V, -V) terminals.

2.4 Output Voltage Adjustment

The output voltage can be finely adjusted within a ±10% range of the rated output voltage using the "+V ADJ" potentiometer. Use a small screwdriver to turn the potentiometer clockwise to increase voltage or counter-clockwise to decrease it. Always verify the output voltage with a multimeter before connecting sensitive equipment.

2.5 Mounting

The power supply is designed for vertical or horizontal installation. Refer to the installation dimensions for proper mounting. Ensure adequate ventilation around the unit, especially around the fan, to prevent overheating.

Installation Dimensions: The unit measures approximately 215mm (Length) x 115mm (Width) x 30mm (Height). It features multiple mounting holes: four M4 holes with L=3mm for top/bottom mounting, and four M4 holes with L=5mm on both sides for side mounting. The main mounting pattern has holes spaced 150mm apart lengthwise and 100mm apart widthwise.

Bottom view of the power supply showing mounting holes
Figure 4: Bottom view of the power supply, indicating the positions of mounting holes.

3. Operation

Once properly installed and wired, connect the power supply to the mains. The internal fan will activate as needed to maintain optimal operating temperature. The power supply is equipped with protective features for safe operation.

Top view of the power supply showing the cooling fan
Figure 5: Top view of the power supply, highlighting the integrated cooling fan for thermal management.

4. Maintenance

The STEPPERONLINE 400W Switching Power Supply requires minimal maintenance. To ensure longevity and reliable performance:

  • Keep the unit clean and free from dust and debris.
  • Ensure the ventilation openings and fan are not obstructed.
  • Periodically check all wiring connections for tightness and integrity.
  • Operate the unit within its specified environmental conditions.

5. Troubleshooting

This power supply is designed with self-recovery protective features. If an issue occurs, the unit may temporarily shut down and attempt to recover.

  • No Output Power:
    • Check the input voltage selector switch (115V/230V) is correctly set.
    • Verify the input power connection.
    • Ensure there is no short circuit or overload on the output. The unit has short circuit protection and overload protection (5S@180%-220% self-recovery).
  • Overheating:
    • Check for obstructed ventilation.
    • Ensure the ambient temperature is within the specified operating range.
  • Unstable Output Voltage:
    • Verify the load is within the rated specifications.
    • Check for loose connections.

If problems persist, discontinue use and consult the official user manual PDF or contact customer support.

6. Specifications

6.1 General Specifications

  • Dimensions: 215mm x 115mm x 30mm
  • Serial No.: LE AC/DC
  • Rated Output Power: 400W
  • EMI Filtering: Internal EMI filter
  • Cooling: Fan cooling
  • Installation Method: Vertical/Horizontal

6.2 Input Specification

Parameter Value
Input voltage 115/230Vac ±20%
Input frequency 47~63Hz
Inrush current 40A/230VAC (cold state)

6.3 Output Specification

The output current varies based on the specific output voltage model. All models provide 400W of power.

Parameter Value (LE-400-24) Value (LE-400-36) Value (LE-400-48)
Output voltage/current 24V/16.6A 36V/11.0A 48V/8.3A
Rated Output Power 400W
Output voltage stability 0.5%
Linear adjustment rate ≤0.5%
Ripple and noise ≤1% Vout
Temperature coefficient ≤0.02%/°C (maximum value)
Output voltage adjustable range ±10% (rated output voltage)
Overall machine efficiency ≥89.5%
Rise time 50ms (230Vac, full load)
Holding time 20ms (230Vac, full load)

6.4 Security Specification

Parameter Value
Dielectric strength Vin~Vout/1500VAC/min, Vin~FG/1500VAC/min, Vout~FG/500VAC/min
Insulation resistance ≥100MΩ
Leakage current <0.5mA/230VAC
Protective Short circuit protection (self-recovery), Overload protection 5S@180%-220% (self-recovery)
Mean time between failures MTBF≥5×105h

6.5 Environmental Characteristics

Parameter Value
Working temperature 0°C~45°C@100%, -10°C @80%, 60°C @40%
Storage temperature -20°C~85°C
Relative humidity 20%~90%RH (no condensation)

6.6 EMC Standards

Designed to comply with:

  • EN55022. ClassC
  • EN61000-3-2,3
  • EN61000-4-2,3,4,5,6,8,11

6.7 Safety Standards

Safety standard design complies with GB4943, EN60950, UL60950.

7. Warranty and Support

This STEPPERONLINE 400W Switching Power Supply comes with a 1-year warranty from the date of purchase. This warranty covers defects in materials and workmanship under normal use. It does not cover damage caused by misuse, accident, unauthorized modification, or improper installation.

For detailed warranty terms, technical support, or further inquiries, please refer to the official user manual PDF or contact STEPPERONLINE customer service.

A comprehensive user manual in PDF format is available for download: View User Manual (PDF)

8. User Tips

No specific user tips were available from reviews or Q&A for this product. Always ensure correct input voltage selection and proper ventilation for optimal performance and longevity.

9. Frequently Asked Questions (FAQ)

No specific frequently asked questions were available from Q&A for this product. For common questions regarding power supplies or stepper motor applications, please consult online resources or contact technical support.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.