eletechsup RT5BF01

Contents

eletechsup RT5BF01 VHF/UHF Radio Wireless Transceiver Board User Manual

1. Introduction

The eletechsup RT5BF01 is a versatile wireless data transmission module designed to convert RS485 data signals into wireless signals and vice-versa. Operating in the 426MHz~508.5MHz frequency band, it enables seamless communication between RS485 devices over a specified distance without the need for extensive wiring. This module simplifies remote operation of RS485 devices, making it ideal for various industrial and home automation applications.

2. Safety & Warnings

Please read all instructions carefully before use. Failure to follow these instructions may result in damage to the product or personal injury.

  • Keep the device and its cord out of reach of children under 3 years old.
  • Keep away from children unless supervised by an adult.
  • Do not use this product for purposes other than its intended use.
  • Inspect the product before each use; do not use if damaged.
  • Do not expose to water or moisture.
  • Handle with care to avoid cuts or injuries.

3. Product Overview

The RT5BF01 module facilitates wireless communication for RS485 devices. It features user-friendly DIP switches for setting key parameters like baud rate and communication channel, simplifying setup. The module is designed for robust performance in various environments.

RT5BF01 Module with labeled components

Figure 1: RT5BF01 Module Components

NumberFunctionDescription
1AntennaSMA Antenna interface
2Power InterfaceDC 8~25V power supply
3PWR Indicator lightPower indicator, blinks 5 times after power up and then lights up long
4RS485 InterfaceConnecting RS485 devices (A+, B-)
5RX Indicator lightWireless receive indicator, flashes when data is received wirelessly
6TX Indicator lightWireless transmit indicator, blinks after successful wireless data transmission
7Baud rate selectionReference baud rate selection table (DIP switches 1-2)
8Channel selectionReference channel selection table (DIP switches 3-6)

4. Setup

4.1. Before First Use

  • Remove all protective films from the device.

4.2. Power Connection

  • Connect a DC power supply (8-25V, 12V recommended) to the Power Interface (2).

4.3. Antenna Installation

  • Screw the provided SMA antenna onto the SMA Antenna interface (1).

4.4. RS485 Connection

  • Connect your RS485 devices to the RS485 Interface (4), ensuring correct polarity (A+ and B-).

4.5. DIP Switch Configuration

The RT5BF01 module uses DIP switches for setting the baud rate and communication channel. Ensure all modules intended to communicate are configured with the same baud rate and channel.

DIP switch settings for baud rate and channel

Figure 2: Baud Rate and Channel Selection DIP Switch Settings

4.5.1. Baud Rate Selection (DIP Switches 1-2)

Set DIP switches 1 and 2 according to the desired baud rate:

DIP 1DIP 2Baud Rate
OFFOFF9600 (Default)
ONOFF19200
OFFON38400
ONON115200

4.5.2. Channel Selection (DIP Switches 3-6)

Set DIP switches 3, 4, 5, and 6 to select one of 16 available channels (0-15). The radio frequency of the module is calculated as: Channel * 5.5MHz + 426MHz. Ensure all communicating modules are set to the same channel.

DIP 3DIP 4DIP 5DIP 6Channel
OFFOFFOFFOFF0
ONOFFOFFOFF1
...............
ONONONON15

5. Operating Modes

5.1. One-to-One Transmission

In this mode, two RT5BF01 modules communicate directly with each other. Each module acts as both a transmitter and receiver, forwarding data between two RS485 devices.

One-to-One Transmission Diagram

Figure 3: One-to-One Transmission Setup

5.2. One-to-Many Transmission (Master-Slave)

This mode allows one master RT5BF01 module to communicate with multiple slave RT5BF01 modules, similar to a wired RS485 bus. Up to 63 modules can be cascaded (an RS485 repeater is recommended for more than 16 modules).

One-to-Many Transmission Diagram

Figure 4: One-to-Many Transmission Setup

5.2.1. Data Flow in Master-Slave Mode

  • When the master device transmits data, all slave devices receive the data.
  • When any slave device transmits data, the master device and all other slave devices can receive it.
  • Important: Only one device (master or any slave) is allowed to transmit data at any given time to avoid data collisions.

6. Indicators

  • PWR Indicator Light (3): Blinks 5 times upon power-up, then remains steadily lit, indicating the module is powered on.
  • RX Indicator Light (5): Flashes when the module receives data wirelessly.
  • TX Indicator Light (6): Blinks after successful wireless data transmission.

7. Maintenance

  • After use, turn off the device.
  • Store the module in a dry place, away from moisture and extreme temperatures.
  • Handle the device with care to prevent physical damage.
  • Keep the antenna free from obstructions and damage.

8. Troubleshooting

  • No Communication:
    1. Verify that all modules are powered on (PWR indicator lit).
    2. Check RS485 wiring for correct polarity (A+ to A+, B- to B-).
    3. Ensure all communicating modules have the same baud rate setting.
    4. Ensure all communicating modules have the same channel setting.
    5. Confirm antennas are securely attached.
  • Intermittent Connection or Poor Range:
    1. Check the distance between modules; ensure it's within the specified range (800-1000m unobstructed).
    2. Minimize physical obstructions (walls, metal structures) between modules.
    3. Check for potential sources of RF interference in the operating frequency band.
    4. Ensure antennas are positioned vertically and are not obstructed.

9. Specifications

RT5BF01 Module front and side view with specifications

Figure 5: Module Dimensions and Key Specifications

ParameterValue
Supply VoltageDC 8-25V (12V recommended)
Working Current18-30mA
Baud Rate9600/19200/38400/115200 (Default: 9600, N, 8, 1)
Wireless Operating Frequency426MHz~508.5MHz (16 channels, 5.5MHz spacing, Default: 426MHz)
Transmit Power20dBm
Receiving Sensitivity-121dBm
Wireless Transmission Distance800-1000m (unobstructed open space)
Communication InterfaceRS485
Cascading CapacityMax 63 modules (RS485 repeater for >16 modules)
Dimensions107 x 54 x 32mm
Weight72g

10. User Tips

  • For optimal wireless transmission range and stability, ensure a clear line of sight between communicating modules.
  • Always double-check that all modules in a network are configured with identical baud rates and communication channels.
  • When setting up larger networks (more than 16 modules), consider using an RS485 repeater to maintain signal integrity and reliability.
  • Mount antennas vertically for best performance.

11. Warranty & Support

For technical support, warranty inquiries, or further information regarding the RT5BF01 module, please contact the manufacturer:

  • Manufacturer: Guangzhou Keshen Electronic Technology Co., Ltd
  • Email: eletechsup@163.com

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.