1. Product Information
This document provides instructions for the AD828 Stereo Dynamic Microphone Preamplifier Board. This module is designed to amplify low-level microphone signals for various electronic applications.
Product Overview
Description for non-visual users: The image displays a small, rectangular red PCB (Printed Circuit Board). Key components visible include a black integrated circuit (IC) labeled 'AD828', several surface-mount resistors and capacitors, and a larger electrolytic capacitor. The board has clearly marked solder pads for 'VCC' (power supply), 'IN' (audio input), 'OUT' (audio output), and 'GND' (ground).
Key Features
- High-quality materials for reliable performance.
- Compact size for easy integration.
- Stereo preamplifier for dynamic microphones.
- Wide operating voltage range: DC 3.8V-15V.
2. Safety & Warnings
Read all instructions before use. Failure to follow these instructions may result in damage to the product or personal injury.
- Keep the device and its cord out of reach of children under 3 years old.
- Keep away from children unless supervised by an adult.
- Do not use this product for purposes other than its intended use.
- Inspect the product before each use; do not use if damaged.
- Follow installation and operation guidelines to avoid injury.
- Do not expose to water or moisture.
3. Setup
Initial Preparation
- Before first use, remove any protective films from the device.
- Ensure all connections are made with the power supply disconnected.
Wiring Instructions
The board features clearly labeled connection points:
- VCC: Connect to the positive terminal of your DC power supply (3.8V-15V).
- GND: Connect to the negative terminal of your DC power supply and the ground of your audio signals.
- IN: Connect the audio input from your dynamic microphone.
- OUT: Connect the amplified audio output to your desired audio processing unit or amplifier.
Important Power Supply Note:
This microphone amplifier board does not include a power regulator circuit. It is crucial to use a stable DC power source such as a battery or a linear regulated power supply. Do NOT use a switching power supply, as this may introduce significant interference (noise) into the audio signal.
4. Operating Instructions
- Ensure all wiring connections (VCC, GND, IN, OUT) are correctly made as per the Setup section.
- Connect your dynamic microphone to the 'IN' terminals.
- Connect the 'OUT' terminals to the input of your audio system (e.g., mixer, audio interface, power amplifier).
- Apply power to the VCC and GND terminals using a suitable DC power source (3.8V-15V battery or linear regulated supply).
- Test the audio output. Adjust gain or volume on your receiving audio equipment as needed.
5. Maintenance
- After use, disconnect the power supply from the board.
- Store the module in a dry, dust-free environment.
- Avoid exposing the board to extreme temperatures or humidity.
- Regularly inspect the board for any signs of physical damage or loose connections.
- Keep the board away from children to prevent accidental damage or injury.
6. Troubleshooting
- No Audio Output:
- Check all wiring connections (VCC, GND, IN, OUT) for proper polarity and secure contact.
- Verify that the power supply is within the specified range (DC 3.8V-15V) and is providing sufficient current.
- Ensure the microphone is functional and correctly connected.
- Confirm the receiving audio equipment is powered on and set to the correct input.
- Humming or Noise in Audio:
- Ensure you are using a battery or a linear regulated power supply. Switching power supplies can introduce significant noise.
- Check for proper grounding of all components in your audio chain.
- Keep audio cables away from power cables to minimize interference.
- Distorted Audio:
- Verify that the input signal level from the microphone is not too high, causing clipping.
- Ensure the power supply voltage is stable and within the specified range.
- Product Not Functioning:
- Inspect the board for any visible damage, such as burnt components or broken traces. Do not use if damaged.
- Confirm the power supply is connected with correct polarity. Reverse polarity can damage the module.
7. Specifications
| Attribute | Value |
|---|---|
| Model Number | AD828 |
| Package Type | DIP |
| Working Voltage | DC 3.8V-15V |
| Board Size (L x W) | 33mm x 20mm (approx. 24.8mm x 16.3mm as per diagram) |
| Application | Computer (general electronic projects) |
| Type | Voltage Regulator (Note: This is a preamplifier, not a voltage regulator. Classification may be generic.) |
| Operating Temperature | -40°C to +85°C |
| Condition | New |
Description for non-visual users: The image shows the red PCB with measurement lines indicating its length as 24.8mm and width as 16.3mm.
8. User Tips
Based on user feedback, the product is generally well-received for its functionality. No specific operational tips or common issues were highlighted in the available reviews or Q&A. Always ensure a stable and clean power supply (battery or linear regulator) to avoid noise, as this is a critical factor for audio circuits.
9. Warranty & Support
Manufacturer Information
Manufacturer: Shenzhen Xingyao Electronics Co., Ltd.
Address: 917 Nanguang Jiejia Building, Shennan Middle Road, Huaqiangbei Street, Futian District, Shenzhen, China
Email: 2753728350@qq.com
Telephone: +86-15376019940
EU Authorized Representative Information
Company Name: TOCYA TRADING
Address: 79 rue de patay, 75013, Paris
Email: TOCYATRADING75013@outlook.com
Telephone: +33-143443019
Compliance
This product has been tested and found in compliance with the RoHS 2.0 Directive (EU) 2015/863 (EU 2017/2102 amending Annex III to Directive 2011/65/EU).
For detailed compliance information, please refer to the Certificate of Conformity (Certificate Number: BTT20260209587RC-1) issued by BTT Better Testing Certification.
A PDF version of the user manual is available for download: View User Manual (PDF)