Fenvi AC1200 Dual-Band WiFi Repeater

Product Overview

The Fenvi AC1200 Dual-Band WiFi Repeater is designed to extend the coverage and improve the signal strength of your existing wireless network. It supports both 2.4GHz and 5GHz bands, offering a combined speed of up to 1200Mbps (867Mbps on 5GHz and 300Mbps on 2.4GHz). This device is ideal for eliminating Wi-Fi dead zones and providing a stable, high-speed connection for various devices throughout your home or office.

The repeater enhances wireless performance, especially for penetrating walls, supporting 5G (867Mbps) for HD video and gaming, and 2.4G (300Mbps) for general internet use.

Specifications

Note: Wireless transmission rates are theoretical maximums. Actual data throughput and wireless coverage will vary.

Setup Guide

There are two primary methods to set up your Fenvi AC1200 WiFi Repeater: using the WPS button for quick setup or through a web browser for manual configuration.

Method 1: WPS Quick Setup (Recommended)

This method allows for a fast and easy connection to your existing router if it supports WPS.

1. Power On: Plug the WiFi Repeater into an electrical outlet near your main router. Wait for the Power LED to light up.
2. Activate WPS on Router: Press the WPS button on your main router. Refer to your router's manual for the exact location and timing.
3. Activate WPS on Repeater: Within 1-2 minutes of pressing WPS on your router, press the WPS button on the Fenvi Repeater.
4. Wait for Connection: The Extender, 5G, and 2.4G indicator lights on the repeater should turn solid, indicating a successful connection. This may take 1-2 minutes.

WPS Quick Setup: Press the WPS button on your router, then on the repeater, and wait for the connection to establish. Your host router must support WPS, and the SSID and password will be the same as the router (special characters are not supported).

Method 2: Manual Setup via Web Browser

Use this method if your router does not support WPS or if you prefer to customize settings.

Mobile Phone Setup:

1. Plug In: Plug the WiFi Repeater into an electrical outlet. Wait for approximately 30 seconds until the 2.4G and 5G lights are both on.
2. Connect to Repeater's SSID: On your mobile phone, go to Wi-Fi settings and connect to the repeater's default SSID, typically named "Fvpro_5G/2.4G" followed by the last 5 digits of its MAC address. The default password is usually "12345678". Ensure your mobile data is turned off.
3. Open Web Browser: Open a web browser (e.g., Chrome, Safari) and type 192.168.188.1 into the address bar.
4. Login: Enter the default login password, which is "admin".
5. Scan and Select Host Router: The repeater will scan for available networks. Select your host router's SSID (both 2.4G and 5G options will be available; choose one to extend).
6. Enter Host Router Password: Input the Wi-Fi password of your main router.
7. Set Extender SSID and Password (Optional): You can choose to keep the same SSID/password or set a new one for the extended network. If you don't modify, proceed to the next step.
8. Confirm Settings: Review the wireless information and click "Start Connect". Wait 30-60 seconds for the extender to connect.
9. Reconnect: Once connected, the "Extender" indicator light will turn on. Reconnect your mobile phone to the new extended Wi-Fi network.

Step-by-step guide for configuring the repeater using a mobile phone's web browser.

PC Setup:

The steps for PC setup are similar to mobile phone setup, using a web browser to access the repeater's configuration page.

1. Plug In: Plug the WiFi Repeater into an electrical outlet. Wait for approximately 30 seconds until the 2.4G and 5G lights are both on.
2. Connect to Repeater's SSID: On your PC, connect to the repeater's default SSID (e.g., "Fvpro_5G/2.4G").
3. Open Web Browser: Open a web browser (e.g., Google Chrome, Firefox) and type 192.168.188.1 into the address bar.
4. Login: Enter the default login password, which is "admin".
5. Scan and Select Host Router: The repeater will scan for available networks. Select your host router's SSID.
6. Enter Host Router Password: Input the Wi-Fi password of your main router.
7. Set Extender SSID and Password (Optional): You can choose to keep the same SSID/password or set a new one for the extended network.
8. Confirm Settings: Review the wireless information and click "Start Connect". Wait 30-60 seconds for the extender to connect.
9. Reconnect: Once connected, the "Extender" indicator light will turn on. Reconnect your PC to the new extended Wi-Fi network.

Step-by-step guide for configuring the repeater using a PC's web browser.

Operating Modes

The Fenvi AC1200 WiFi Repeater supports multiple operating modes:

• Repeater Mode: Extends the existing Wi-Fi signal of your main router. This is the most common use case.
• Access Point (AP) Mode: Connects to your wired network via an Ethernet cable and broadcasts a new wireless network. This is useful for adding Wi-Fi capability to a wired-only network or creating a new Wi-Fi hotspot. The device features a 10/100Mbps WAN/LAN port for this purpose.

After successful setup, the repeater will broadcast an extended Wi-Fi network. You can connect your devices (smartphones, tablets, laptops, smart TVs, gaming consoles, etc.) to this extended network for improved coverage and speed.

The repeater offers wide compatibility, capable of connecting up to 35 devices simultaneously.

Maintenance

To ensure optimal performance and longevity of your WiFi Repeater, consider the following maintenance tips:

• Placement: Position the repeater in a central location between your router and the desired coverage area. Avoid placing it near large metal objects, concrete walls, or other electronic devices that may cause interference.
• Firmware Updates: Periodically check the manufacturer's website for firmware updates. Keeping the firmware updated can improve performance, stability, and security.
• Cleaning: Keep the device clean and free from dust. Use a soft, dry cloth to wipe the exterior. Do not use liquid cleaners or aerosols.
• Ventilation: Ensure the repeater has adequate ventilation to prevent overheating. Do not cover the device or place it in an enclosed space.
• Restart: If you experience network issues, try restarting the repeater by unplugging it from the power outlet for 10 seconds and then plugging it back in.

Troubleshooting

• No Internet Access After Setup:
  • Ensure the repeater is successfully connected to your main router (Extender, 5G, and 2.4G lights are solid).
  • Verify that the Wi-Fi password entered for your main router during setup was correct.
  • Try restarting both your main router and the repeater.
  • If using manual setup, ensure your mobile data was off during the configuration process to avoid conflicts.
• Weak Signal from Repeater:
  • Relocate the repeater closer to your main router, ensuring it's still within a good signal range of the router but also closer to the area needing coverage.
  • Avoid physical obstructions like thick walls or large appliances.
• WPS Setup Fails:
  • Ensure your main router supports WPS.
  • Try the manual setup method via a web browser.
  • Some routers may require WPS to be enabled in their settings.
• Cannot Access 192.168.188.1:
  • Ensure your device is connected to the repeater's default Wi-Fi network (e.g., "Fvpro_5G/2.4G"), not your main router's network or mobile data.
  • Try a different web browser.
  • Reset the repeater to factory defaults (see Maintenance section) and try again.
• Extended Network Password: During manual setup, you have the option to set a new password for the extended network, different from your main router's password. If you did not set a new one, it will default to your main router's password.

User Tips

• Easy Setup: Many users find the setup process, especially WPS, to be quick and straightforward.
• Stable Connection: The repeater generally provides a stable and reliable connection, even through thick walls.
• Dual-Band Visibility: The device clearly broadcasts both 2.4GHz and 5GHz networks, allowing you to choose the best frequency for your needs.
• Access Point Mode: Utilize the Ethernet port to convert a wired connection into a new Wi-Fi hotspot, which is great for areas without existing wireless coverage.
• Reset for Issues: If you encounter persistent issues, a factory reset (pressing and holding the reset button for several seconds) can often resolve them.

Warranty and Support

For detailed warranty information and technical support, please refer to the official product documentation or contact the seller directly. A comprehensive user manual in PDF format may also be available for download from the seller's product page or support section.

For a detailed user manual, please refer to the User Manual (PDF).