1. Introduction
This manual provides detailed instructions for the EJEAS 3.5mm Audio Plug Microphone Speaker Headset and Helmet Intercom Clip, designed for use with EJEAS V4 and V6 motorcycle intercom systems. This accessory enhances your riding experience by providing clear audio communication and music playback capabilities when connected to a compatible EJEAS intercom unit.
The EJEAS V6 intercom system, which this headset connects to, is a performance-stable helmet Bluetooth intercom. It supports automatic reception of phone calls, offers waterproof design, and HD-Voice quality, ensuring safe and convenient communication for motorcycle riders.
2. Package Contents
Please check the package for the following items:
- Microphone Speaker Headset (with 3.5mm audio plug)
- Helmet Intercom Clip
- Metal Sheet (for clip mounting)

Image: EJEAS Headset Package Contents. Shows two sets of microphone speaker headsets, two helmet intercom clips, and two metal sheets.

Image: EJEAS Headset Wiring Diagram. Shows the 3.5mm audio plug connected to two speaker pads and a boom microphone.
3. Setup and Installation
3.1. Headset and Clip Installation on Helmet
Follow these steps to properly install the intercom clip and headset onto your helmet:
- Attach the Intercom Clip: Secure the intercom clip to the left side of your helmet. You can either slide it onto the helmet edge or use the included metal sheet and adhesive for a more permanent mount. Ensure it is firmly attached.
- Mount the Intercom Unit: Slide your EJEAS V4 or V6 intercom unit onto the installed clip until it clicks securely into place.
- Position Speakers: Place the two speaker pads inside your helmet's ear pockets. Ensure they are positioned comfortably over your ears for optimal audio clarity.
- Position Microphone: Attach the microphone to the inside of your helmet, positioning it close to your mouth for clear voice transmission.
- Connect Headset: Plug the 3.5mm audio jack from the headset into the corresponding earphone interface on your EJEAS V4 or V6 intercom unit.

Image: Helmet Intercom Installation Diagram. Illustrates the five steps of attaching the clip, mounting the intercom, positioning speakers, positioning the microphone, and connecting the headset.

Image: Close-up of Helmet Intercom Clip. Shows the black plastic clip with two screws for attachment.
3.2. Connecting Intercom Unit with Phone (GPS/MP3)
To pair your EJEAS V4 or V6 intercom unit with your mobile phone, GPS device, or MP3 player (if it supports Bluetooth):
- With the intercom unit powered off, long press the Phone button for approximately 5 seconds until the red and blue indicator lights flash alternately. This indicates pairing mode.
- On your phone or device, enable Bluetooth and search for available devices.
- Select "V6" (or similar EJEAS device name) from the list to connect.
- Once successfully paired, the intercom's blue light will flash, indicating a successful connection.
4. Operating Instructions (Intercom Unit Functions)
The following operations are performed on your EJEAS V4 or V6 intercom unit, which your headset is connected to.
4.1. Intercom Unit Button Functions

Image: EJEAS V6 Intercom Button Layout. Diagram showing the top view of the intercom unit with numbered buttons and their corresponding labels.
| No. | Button/Interface | Function |
|---|---|---|
| 1 | MOTOR/A button | Power on / Intercom with A device |
| 2 | B button | Intercom with B device |
| 3 | C button | Intercom with C device |
| 4 | D button | Intercom with D device |
| 5 | E button | Intercom with E device |
| 6 | Phone button | Call functions (answer, end, redial) / Music play/pause |
| 7 | Volume + | Increase volume / Next music |
| 8 | Volume - | Decrease volume / Previous music |
| 9 | Power off | Power off the device |
| 10 | Antenna | For signal transmission |
| 11 | Earphone / USB charger interface | Connect headset / Charge device |
4.2. Power On/Off
- Power On: Long press the MOTOR button for about 2 seconds until the main device light flashes.
- Power Off: Press the Power off button.
4.3. Phone Call Operations
- Receiving a Call: If no operation is performed within 5 seconds of an incoming call, the phone will automatically answer.
- Refusing a Call: When a call comes in, press the Phone button to end the call.
- Last Number Redial: After connecting to your phone, long press the Phone button for 3 seconds. The device will automatically dial the last outgoing call number.
4.4. Music Playback
- Play/Suspend Music: Short press the Phone button.
- Volume Control: Press Volume + to increase volume, or Volume - to decrease volume.
- Choose Music (Previous/Next): Long press Volume - for 2 seconds for the previous track. Long press Volume + for 2 seconds for the next track.
4.5. Intercom Operations
The EJEAS V6 intercom system supports up to six riders, with two riders able to talk simultaneously. One main device can be paired with up to five sub-devices (A, B, C, D, E). The main device can select one sub-device to communicate with at a time.
- Pairing with A Device: Long press the MOTOR buttons on both the main device and the A device simultaneously for about 5 seconds. Both devices' red and blue lights will flash. Once they find each other, one will initiate pairing, and the blue light will flash quickly. After a successful connection, the blue lights will flash slowly simultaneously, and the two devices can communicate. To pair another sub-device, first press the MOTOR button to disconnect.
- Pairing with B Device: Long press the B buttons on both the main device and the B device simultaneously for about 5 seconds. Follow the same light indicator sequence as for pairing with device A. To pair another sub-device, first press the B button to disconnect.
- Pairing with C, D, and E Devices: Follow the same pairing procedure as for devices A and B, using their respective C, D, or E buttons.
- Switching Between Paired Devices: To talk to a specific sub-device (A, B, C, D, or E), press the corresponding MOTOR/B/C/D/E button on the main device. This allows the main device to switch communication between different paired sub-devices.
Note: Once paired, you do not need to pair again for subsequent uses. Simply click the corresponding button on the main device to connect and talk.
5. Maintenance
5.1. Charging the Intercom Unit
- When the intercom unit is charging, the red indicator light will remain on.
- Once fully charged, the red indicator light will turn off.
- To ensure optimal battery life, always use the standard charger provided with your EJEAS intercom unit.
5.2. General Care
- Keep the headset and intercom unit dry. Avoid exposure to excessive moisture.
- Clean the devices with a soft, dry cloth. Do not use harsh chemicals or abrasive cleaners.
- Ensure the headphone jack is fully inserted into the device, especially in rainy conditions, to prevent water ingress.
6. Troubleshooting
6.1. Clear Pairing (Restore Factory Settings)
If you experience pairing issues or wish to reset all Bluetooth connections:
- Press the Phone button and B button on the intercom unit simultaneously.
- The indicator light will flash red three times and then blue once, confirming that all pairing records have been cleared.
6.2. Interference
This device complies with relevant regulations regarding electronic interference. Operation is subject to the following conditions:
- This device may not cause harmful interference.
- This device must accept any interference received, including interference that may cause undesired operation.
If you experience persistent issues, ensure the device is fully charged and try re-pairing it with your phone or other intercom units.
7. Specifications
| Feature | Specification |
|---|---|
| Brand Name | EJEAS |
| Model Name | for V6.V4 (3.5mm Plug) |
| Item Type | Helmet Bluetooth headset |
| Connection Mode | Wire (3.5mm audio jack) |
| Applicable Helmet Type | MODULAR, MOTOCROSS, Open face, Full Face, Flip Up Helmet |
| External Testing Certification | CE |
| Origin | Mainland China |
| Item Length | 8 cm |
| Item Width | 5 cm |
| Item Height | 1.8 cm |
| Item Weight | 10 g |
| Package Length | 18 cm |
| Package Width | 10 cm |
| Package Height | 2 cm |
| Package Weight | 0.173 kg |
Note: Specifications related to intercom distance, number of speakers, and power supply mode (built-in battery) refer to the EJEAS V4/V6 intercom unit itself, not this accessory headset.
8. User Tips
- Durability of Clip: For long-term durability, consider using the included metal clip piece for mounting, as plastic clips may show wear over several years of use.
- Noise Filtering: The microphone cable is designed with excellent wind and contact noise filtering, contributing to clear communication even at speed.
- Compatibility Check: This headset uses a 3.5mm audio jack and is specifically designed for EJEAS V4 and V6 intercom systems. It is not compatible with newer EJEAS V6 models that may use USB 3.0 connections, nor is it designed for V8 systems. Always verify your intercom unit's port type before purchase.
- Simultaneous Functions: The intercom unit typically handles communication and music playback as separate functions. Refer to your intercom unit's manual for details on simultaneous operation capabilities.
- Optimal Communication: For best communication distance, it is recommended to use the intercom system in open areas.
- Safety First: For riding safety, it is not recommended to manually operate device buttons while riding. Focus on the road.
9. Warranty and Support
For detailed operational instructions, troubleshooting, and warranty information regarding your EJEAS V4 or V6 intercom unit, please refer to the full user manual provided with your intercom unit. A digital version of the EJEAS V6pro User Manual can be found at: EJEAS V6pro User Manual (PDF).
If you encounter any issues or require further assistance, please contact the seller or EJEAS customer support.