1. Introduction
Thank you for choosing the noqiz M22 SN Smart Lock. This manual provides detailed instructions for the installation, programming, and operation of your new keyless entry door lock. Please read this manual thoroughly before operating your device to ensure proper function and safety.
The noqiz M22 SN Smart Lock offers convenient keyless access with a touchscreen keypad, supporting up to 50 user codes. It is designed for easy installation and provides enhanced security for your home or office.
2. Safety Information
- Do not use an electric screwdriver during installation to avoid overtightening and damaging components.
- Do not load batteries until the lock is completely installed and the door handing process is performed.
- Ensure the key is pulled out when installing the exterior assembly.
- Use only 4 brand new AA alkaline batteries. Do not mix used and new batteries, and do not use rechargeable or non-alkaline batteries.
- Change the default Master Code (123456) to your own unique code immediately after initial setup for security.
- Keep your Master Code confidential.
3. Parts List
Before beginning installation, verify that all parts are present and undamaged. If any parts are missing or damaged, please contact customer support.
Image: Detailed diagram showing all components included in the smart lock package.
| Item | Description | Quantity |
|---|---|---|
| A | Latch | x1 |
| B | Exterior Assembly | x1 |
| C | Interior Assembly | x1 |
| D | Mounting Plate | x1 |
| E | Strike Plate | x1 |
| F | Battery Cover | x1 |
| G | 3/4" (19mm) Strike/Latch Screws | x4 |
| H | 1-5/16" (33mm) Mounting Plate Screws | x2 |
| I | 3/4" (19mm) Interior Assembly Screws | x2 |
| J | Buckle Box | x1 |
| K | Backup Key | x2 |
| IC Card | x2 |
4. Installation Guide
Read this manual carefully before installing and operating. For a visual guide, you can scan the QR code provided in the original manual for online videos.
4.1. Prepare the Door and Check Dimensions
If you need to drill a new door, use the supplied template and follow these instructions:
- Measure to confirm the hole in the door is 2-1/8" (54mm).
- Measure to confirm the hole in the door edge is 1" (25mm).
- Measure to confirm the backset is either 2-3/8" or 2-3/4" (60 or 70mm).
- Measure to confirm the door thickness is 1-3/8" to 2" (35mm or 50mm).
- Ensure the hole in the door frame is drilled a minimum of 1" (25mm) deep.
Image: Diagrams illustrating how to measure door dimensions for proper lock fit.
4.2. Instructions for Drilling a New Door
Use the provided template for accurate drilling:
- Cut out the template printed in the manual.
- Fold the template and place it on the door 36" (915mm) from the ground as marked.
- Mark the center hole on the door edge through the template for a 1" (25mm) latch bolt.
- Mark the center hole on the door face through the template for a 2-3/8" (60mm) or 2-3/4" (70mm) backset.
- Drill a 2-1/8" (54mm) hole through the door panel as marked for the lock set.
- Drill a 1" (25mm) hole in the center of the door edge for the Deadbolt Latch Assembly.
- Insert the Deadbolt Latch Assembly, keeping it parallel to the face of the door. Mark its outline and remove the latch.
- Chisel 5/32" (4mm) deep or until the latch face is flush with the door edge.
Image: Drilling template with measurements and instructions for marking and drilling the door.
Image: Visual guide for marking the door face and edge using the template.
Image: Steps for drilling the main hole and the latch bolt hole, followed by chiseling for a flush fit.
4.3. Install the Latch and Strike
- Determine Backset and Adjust Latch: Hold the latch in front of the door hole, with the latch face flush against the door edge. If the slotted hole is not centered, twist the latch and adjust the bolt length until it is centered. Ensure the latch bolt is retracted.
- Install Latch: Insert the latch into the door edge and secure it with the provided Latch Screws (G).
- Test Deadbolt: Use a screwdriver to test if the deadbolt works smoothly.
- Mark and Drill Door Jamb: Mark the center hole on the edge of the jamb even with the center of the Latch Bolt on the door edge. Drill a 1" (25mm) hole, 1-3/16" (30mm) deep, in the door jamb on the center mark.
- Install Strike Plate: Outline the outside edges of the Strike Plate. Chisel 5/32" (4mm) deep or until the strike plate is flush with the door surface. Install the Strike Plate using two 3/4" (19mm) screws (G).
Image: Instructions for adjusting the latch backset and securing it into the door edge.
Image: Steps for testing the deadbolt mechanism and installing the strike plate on the door jamb.
4.4. Install Exterior Assembly
Route the cable through the door below the bolt and push the keypad onto the door. IMPORTANT: The key must be pulled out when installing.
Image: Diagram showing how to route the cable and install the exterior keypad assembly.
4.5. Install Interior Assembly
- Take off the mounting plate (D) from the interior assembly by loosening the 2 screws.
- Route the cable through the bottom of the mounting plate.
- Tighten the mounting plate to the door. Note: Support the exterior assembly during mounting plate installation.
- Ensure a tight cable connection between the exterior and interior assemblies. The smooth side of the plug should be at the bottom.
- Tighten the interior assembly screws (I).
- Insert the key and test the latch. If the latch does not extend or retract smoothly, adjust the mounting plate screws. If the keypad and mounting plate are deflected, loosen the mounting plate screws and adjust.
Image: Steps for installing the interior mounting plate and securing it to the door.
Image: Diagram showing how to connect the cable and test the latch mechanism after interior assembly installation.
4.6. Install Batteries and Perform Door Handing Process
- While the door is OPEN and UNLOCKED, load 4 AA batteries into the battery compartment.
- Perform the door handing process: Press the SET button. The latch bolt should extend by itself.
- Enter the preset programming code: 123456, then press the Lock button. The latch bolt should retract by itself.
IMPORTANT: Do not use rechargeable batteries or non-alkaline batteries. Make sure the door is unlocked and that you are using a fresh set of batteries.
Image: Steps for inserting batteries and performing the door handing process to calibrate the lock.
5. Operating Instructions
5.1. At a Glance
Image: Diagram highlighting the Indicator Light, Lock and Clear button, Keypad, Unlock/Programming button, Keyhole, SET Button, Battery Door, and Turn Knob.
5.2. How to Use
- Unlock from Outside: Enter Master Code + Lock button OR User Code + Lock button OR use an IC Card.
- Unlock from Inside: Rotate the thumb turn to the horizontal position.
- Lock from Outside (Auto Lock Mode): The bolt will extend automatically 10 seconds after unlocking.
- Lock from Outside (Manual Mode): Press the Lock button.
- Lock from Inside (Auto Lock Mode): The device will be locked automatically.
- Lock from Inside (Manual Mode): Rotate the thumb turn to the vertical position.
Image: Visual guide for unlocking and locking the smart lock from both the outside and inside.
5.3. Definitions
- Master Code: Required for programming and feature settings. The default is 123456. Must be changed.
- Auto Lock: Automatically locks the deadbolt 10 seconds after unlocking. Delay can be customized (5-30 seconds).
- Key Unlock: Always available when batteries are dead or user codes are forgotten.
- Low Battery Indicator: Red light flashing after pressing any key indicates low battery.
- Wrong Entry Limit: After 5 incorrect user codes within one minute, the lock shuts down for 90 seconds.
- Silent Mode: Mutes keypad beep sounds, but low battery and system alerts will still sound.
5.4. Code Format
- Master Code: 6 digits. Default: 123456.
- User Code: 6-9 digits. Up to 50 user codes can be stored.
- User ID: 2 digits, from 01 to 50.
Factory Default Settings:
- Programming Code: 123456
- User Code: 123456
- User ID: 01
5.5. Quick Set Up (Programming)
IMPORTANT: The default Master Code is 123456. It is required that you change it to your own before programming.
- Change Master Code: SET + Master Code + Lock button, then Press 4 + Lock button, enter New Master Code + Lock button, Re-enter New Master Code + Lock button. (Flashing green light indicates success).
- Add User Code: SET + Master Code + Lock button, then Press 1 + Lock button, enter User ID (2-digit) + Lock button, enter New User Code + Lock button, Re-enter New User Code + Lock button. (Flashing green light indicates success).
- Delete User Code: SET + Master Code + Lock button, then Press 2 + Lock button, enter User ID (2-digit) + Lock button, Re-enter User ID + Lock button. (Flashing green light indicates success).
- Delete All User Codes: SET + Master Code + Lock button, then Press 3 + Lock button, enter Master Code + Lock button. (Flashing green light indicates success).
- Set Auto Lock: SET + Master Code + Lock button, then Press 5 + Lock button, enter Time (5-30 seconds) + Lock button. (Flashing green light indicates success).
- Cancel Auto Lock: SET + Master Code + Lock button, then Press 5 + Lock button, enter 00 + Lock button. (Flashing green light indicates success).
- Silent Mode (On/Off): SET + Master Code + Lock button, then Press 6 + Lock button. Press 1 + Lock button for Sound Off, or Press 2 + Lock button for Sound On. (Flashing green light indicates success).
- Add IC Card: SET + Master Code + Lock button, then Press 7 + Lock button, put IC Card on the keypad. (Flashing green light indicates success).
- Delete All IC Cards: SET + Master Code + Lock button, then Press 8 + Lock button, enter Master Code + Lock button. (Flashing green light indicates success).
5.6. Protection Mode
If 5 incorrect codes are entered within one minute, the keypad will lock for 90 seconds. During this period, 3 beeps and 3 red light flashes will occur if any button is pressed.
How to exit protection mode:
- Wait for 90 seconds; the lock will exit protection mode automatically.
- Remove the battery for more than 5 seconds, then re-insert it.
Notes:
- If the indicator light flashes red, your setting failed. Press SET to re-enter programming mode.
- The SET button is inside the battery compartment.
- When you enter a wrong button, you can press the Lock button to clear it.
6. Maintenance
6.1. Battery Replacement
When the low battery indicator (red light flashing after pressing any key) appears, it's time to replace the batteries. Replace all 4 AA alkaline batteries with new ones. Do not mix old and new batteries, and do not use rechargeable batteries.
6.2. Cleaning
Clean the keypad and lock body with a soft, dry cloth. Avoid using abrasive cleaners or solvents that could damage the finish or electronic components.
7. Troubleshooting
7.1. System Alerts
| Alert | Possible Cause | Solution |
|---|---|---|
| Light flashes red 3 times with 3 beeps. | Door jammed while attempting to lock. | Manually re-lock door. If needed, re-position strike. |
| Unsuccessful programming. | Re-start programming procedure. | |
| Incorrect User Code entered. | Re-enter User Code. | |
| Incorrect IC Card entered. | Re-authorize IC Card. | |
| Light flashes red 3 times with 3 beeps. (after 5 incorrect codes) | 5 incorrect User Codes entered within one minute. | Re-enter User Code 90 seconds after keypad lock out. |
| Red light when pressing any button. | Low battery. | Replace batteries. |
| Red light when pressing any button; cannot unlock/lock. | Super low battery. | Replace batteries. |
| Green light and beeps for 1s after pressing unlock/lock button. The lock gives no response. | Poor quality battery. | Replace batteries. |
| The keypad and light indicator give no response. | Battery run out. | Replace batteries. |
| Bad cable connection. | Re-connect the cable. |
7.2. Common Issues
- Why does the latch not extend but the motor is rotating when resetting my lock?
Improper installation may have caused this. Ensure the latch and strike are aligned. Slightly loosen mounting screws on the external assembly keypad and the latch bolt if screws are overtightened. Open your door and reset the lock.
- Why does the latch not extend and the motor isn't rotating when resetting my lock?
The deadbolt latch should be retracted (unlocked) throughout your installation process. Open your door and reset the lock.
- When I attempt to lock/unlock my deadbolt, why does the latch go in and out for a few times?
This happens when the latch and strike are misaligned. Ensure the bolt hole on the door frame is at least 1" (25mm) deep for full extension. Check if the door closes properly and the deadbolt goes directly into the hole without impacting the strike or door frame.
- Why does my lock only work properly when the backup key is in? Why am I unable to pull the key out in the unlocked position?
You may need to re-install the whole lock. Ensure the lock is in an unlocked status when you start installation. Make sure the turn knob is horizontal. Do not put the backup key in the lock during normal operation.
- What does 3 short and fast beeps mean while programming?
It alerts you to either a time-out or wrong entry. Complete each setting step within 5 seconds. Change the default master code during first-time programming. Ensure user codes are in the correct format (6 to 9 digits).
- What if I forget my Master Codes?
If you forget your Master Code, reset your lock to factory default. The original master code (123456) will then work, and all previous user codes will be erased.
Image: Diagram showing how to reset the lock to factory default settings by pressing the SET button for more than 5 seconds.
8. Specifications
| Feature | Detail |
|---|---|
| Model Number | M22 SN |
| Power Supply | DRY BATTERY (4x AA) |
| Handle Direction | Direction Reversible |
| Protection Level | IP66 |
| Fit Door Thickness | 35-50 mm |
| Ways To Unlock | Mechanical Keys, Password, IC Card |
| User Codes Capacity | Up to 50 |
| Certification | FCC |
| Package Length | 19 cm |
| Package Width | 14 cm |
| Package Height | 11 cm |
| Package Weight | 1.073 kg |
Image: Front and back view of the noqiz M22 SN Smart Lock, showcasing its design and keypad.
Image: Illustration of the auto-lock feature, providing peace of mind.
Image: Highlights IP54 waterproof rating, 1-year battery life, and low battery reminder.
9. User Tips
- Take your time to read the setup instructions carefully; proper installation makes programming and daily use much easier.
- Be cautious when screwing parts during installation to avoid overtightening or damaging the lock components.
- Ensure the bolt hole in the door frame is at least 1 inch (25mm) deep for the deadbolt to extend fully and operate smoothly.
- If you encounter issues with a code not working, double-check your input. If problems persist, consider resetting the lock to factory defaults and reprogramming.
- The lock is noted for its solid and well-built quality, suggesting durability.
- Always change the default Master Code (123456) immediately after initial setup to enhance your security.
10. Warranty and Support
The warranty period for this product is 12 months from the date of purchase. Product specifications are subject to change without notice. The production and sale of this product may be discontinued due to the discontinuation of electronic parts used.
If you suspect a malfunction, please provide the order number, product model number, and a detailed explanation of the failure status. For any questions or inquiries regarding malfunctions, please contact customer support.
The manufacturer will not be held liable for incidental or consequential losses or damages due to acts of God.
A detailed user manual in PDF format is available for download: View User Manual (PDF)