yuyi 98273-1006, 98273-1001, 98276-1001, 185760-1, 185760-2, 185760-4

Contents

16 Pin Computer Board Plug Connector User Manual

Model: 98273-1006, 98273-1001, 98276-1001, 185760-1, 185760-2, 185760-4

1. Introduction

This manual provides instructions for the proper installation, use, and maintenance of your Yuyi 16 Pin Computer Board Plug Connector. This connector is designed for automotive applications, specifically for use with Peugeot and Citroen BSI (Built-in Systems Interface) fuseboxes.

2. Safety & Warnings

Important Safety Information:

  • Read all instructions before use. Failure to follow these instructions may result in damage to the product or personal injury.
  • Non-professionals should not use this product. Installation should be performed by qualified personnel.
  • Do not use this product for purposes other than its intended use in compatible automotive electrical systems.
  • Inspect the product before each use; do not use if damaged.
  • Follow installation and operation guidelines to avoid injury.
  • Do not expose to water or moisture.

3. Package Contents

Each package typically includes the following components:

  • 1x 16-Pin Connector Housing (available in black, grey, white, or green)
  • 1x Red Locking Tab
  • 12x 1.5mm Series Terminals
  • 4x 2.8mm Series Terminals
Image showing four 16-pin connector housings in different colors (grey, green, black, white) with red locking tabs, alongside loose terminals (12 smaller, 4 larger).
Figure 1: Connector components (example shows multiple colors, product is typically one unit).

4. Specifications

FeatureDescription
Brand Nameyuyi
Model Numbers98273-1006, 98273-1001, 98276-1001, 185760-1, 185760-2, 185760-4
OriginMainland China
CertificationNONE
MaterialNylon
Position16 pins car connector
Type1.5/2.8 mm series plug
EU LVD VoltageLow voltage: Below 50Vac or 75Vdc
Wireless FunctionalityNo
Battery IncludedNo
High-concerned chemicalnone
Voltagenone
Available ColorsBlack, Grey, White, Green
GenderFemale
Rear view of four 16-pin connector housings in different colors, showing the numbered pin cavities (1-16).
Figure 2: Rear view of connectors showing pin numbering.

5. Setup & Installation

Installation of this connector requires basic automotive electrical knowledge and appropriate tools. It is recommended that installation be performed by a professional.

Required Tools:

  • Wire strippers
  • Professional crimping pliers (essential for secure connections)
  • Multimeter (for testing connections)

Installation Steps:

  1. Prepare Wires: Carefully strip the insulation from the ends of the wires that will be connected to the terminals. Ensure the stripped length matches the terminal's crimp area.
  2. Crimp Terminals: Using professional crimping pliers, securely crimp the appropriate terminals (1.5mm or 2.8mm series) onto the prepared wire ends. Ensure a strong mechanical and electrical connection.
  3. Insert Terminals: Carefully insert the crimped terminals into the correct cavities of the connector housing. Ensure they click into place, indicating they are fully seated and locked. Refer to Figure 3 for visual guidance.
  4. Secure with Locking Tab: Once all terminals are inserted, push the red locking tab fully into the connector housing. This tab provides secondary locking for the terminals, preventing them from pulling out. Refer to Figure 4 for visual guidance.
  5. Connect to Device: Connect the assembled connector to the corresponding mating connector on the Peugeot/Citroen BSI fusebox or other intended device. Ensure a firm and secure connection.
  6. Test Connection: Before fully reassembling any vehicle components, test all circuits connected through the new connector to ensure proper functionality and continuity.
Close-up image showing a metal terminal being inserted into a cavity of the plastic connector housing.
Figure 3: Inserting a terminal into the connector housing.
Image showing the connector housing with the red locking tab partially inserted, securing the internal terminals.
Figure 4: Securing terminals with the red locking tab.

6. Operating Instructions

As a passive electrical connector, there are no specific operating instructions beyond ensuring it is correctly installed and securely connected. The connector facilitates the electrical connection between two components. Once installed, its operation is integral to the circuit it completes.

7. Maintenance

  • Inspection: Periodically inspect the connector and its wiring for any signs of wear, damage, corrosion, or loose connections.
  • Cleaning: If necessary, gently clean the connector with a non-conductive electrical contact cleaner. Ensure the connector is dry before re-establishing power.
  • Avoid Stress: Ensure that the wiring connected to the plug is not under excessive tension or sharp bends, which could damage the wires or the connector.

8. Troubleshooting

  • No Electrical Continuity:
    • Check that all terminals are fully seated and locked within the connector housing.
    • Verify that the wires are correctly crimped to the terminals.
    • Inspect for any bent or damaged pins on the mating connector.
    • Ensure there is no debris or corrosion obstructing the electrical contacts.
  • Loose Connection:
    • Ensure the red locking tab is fully inserted.
    • Verify that the connector is fully engaged with its mating part.
  • Compatibility Issues: If the connector does not fit or function as expected, double-check the model numbers and ensure it is compatible with your specific vehicle's BSI fusebox or intended application. Some specific vehicle models (e.g., Peugeot 301 BCI) may have variations.
  • Original Connector Damage: If replacing a faulty connector, ensure the issue was indeed with the connector (e.g., burnt pins) and not an upstream electrical problem.

9. User Tips

  • Verify Compatibility: Always confirm the connector's compatibility with your specific vehicle model and component (e.g., BSI fusebox) before purchasing and installing.
  • Professional Installation: For best results and to avoid damage, consider having the connector installed by a qualified automotive technician.
  • Inspect Original: When replacing a faulty connector, carefully inspect the original for signs of damage like burnt pins, which can indicate the root cause of an electrical issue.
  • Quality Crimping: The quality of the crimp connection is crucial for long-term reliability. Invest in or use professional-grade crimping tools.

10. Frequently Asked Questions (FAQ)

Q: Are the terminals included with the connector housing?
A: Yes, the connector housing comes with the necessary terminals (12x 1.5mm series and 4x 2.8mm series) and a red locking tab.

11. Warranty & Support

For technical support, warranty inquiries, or further information, please contact the manufacturer or their authorized representative:

Manufacturer:

Yueqing ChenYi Electric Co., Ltd
Address: 2nd Floor, Building 3, No. 12 Yongxing 1st Road, Chengdong Industrial Functional Zone, Chengdong Street, Yueqing City, Zhejiang Province, China
Phone: +86-15869652718

EU Authorized Representative:

EUREPSTAR GmbH
Address: Schlüterstr. 3, 85057 Ingolstadt, Germany
Phone: +49-84188697744
Email: eurep@eurep-gmbh.de

For a complete product manual and compliance information, you may refer to the official PDF document: View Product Manual (PDF)

Documents and downloads

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.