1. Introduction
Thank you for choosing the SHINEKNOT LED Emergency Lamp. This multi-functional rechargeable bulb is designed to provide reliable lighting in various situations. It functions as a standard household light bulb and automatically switches to emergency lighting during power outages. Its portable design, featuring removable 18650 lithium batteries, also allows it to be used as a mobile emergency light for outdoor activities or when power is unavailable.
2. Safety Instructions
- Always ensure the power is off before installing or removing the bulb.
- Do not use the bulb in wet environments unless specifically designed for it.
- Keep out of reach of children.
- Do not disassemble the bulb beyond battery replacement.
- Use only specified 18650 lithium batteries.
- Avoid direct eye exposure to the LED light for extended periods.
3. Package Contents
Please check the package for the following items:
- 1 x SHINEKNOT LED Emergency Lamp (YJ805)
- 2 x 18650 Lithium Batteries (may be pre-installed)
4. Setup
4.1. Battery Installation
- Locate the battery compartment cover on the side of the bulb.
- Gently slide or pry open the cover to expose the battery slots.
- Insert two 18650 lithium batteries, ensuring correct polarity (+ and - ends match the markings inside the compartment).
- Close the battery compartment cover securely.
Figure 1: Battery compartment and installation
4.2. Bulb Installation
- Ensure the power to the light fixture is turned off.
- Screw the SHINEKNOT LED Emergency Lamp into a standard E27 screw-type light socket until it is snug. Do not overtighten.
- Turn on the power to the light fixture. The bulb will light up if power is available.
5. Operating Instructions
5.1. Normal Operation
When installed in a powered E27 socket, the lamp functions as a regular LED light bulb. It will illuminate when the wall switch is turned on and turn off when the switch is turned off. During this time, the internal batteries will charge automatically.
5.2. Emergency Mode
In the event of a power outage, the lamp will automatically switch to emergency lighting mode, providing illumination using its internal battery power. To activate emergency lighting manually (if the bulb is not in a powered socket):
- Hand-held Activation: Hold the bulb and touch both sides of the E27 screw base with your hand. The bulb will light up.
- Water Activation: Place the bottom of the bulb's E27 screw base into a small amount of water. The bulb will light up.
Figure 2: Emergency lighting activation methods
Figure 3: Detailed view of emergency features
5.3. Product Demonstration Video
Video 1: Product demonstration, including battery replacement and emergency lighting features.
6. Maintenance
6.1. Battery Care
- The lamp uses high-capacity lithium batteries with built-in overcharge and over-discharge protection for longer service life.
- For optimal battery life, ensure the lamp is regularly used in a powered socket to keep the batteries charged.
- If storing the lamp for extended periods, fully charge the batteries before storage and recharge every 3-6 months.
6.2. Cleaning
To clean the lamp, ensure it is disconnected from power and cool. Wipe the exterior with a soft, dry cloth. Do not use abrasive cleaners or immerse the lamp in water.
7. Troubleshooting
| Problem | Possible Cause | Solution |
|---|---|---|
| Lamp does not light up in normal mode. | No power to the socket; bulb not screwed in properly; faulty bulb. | Check power supply; ensure bulb is securely screwed in; test bulb in another working socket. |
| Lamp does not light up in emergency mode. | Batteries are not charged; batteries incorrectly installed; faulty batteries. | Ensure batteries are charged (use in a powered socket for a few hours); check battery polarity; replace batteries. |
| Short emergency lighting duration. | Batteries not fully charged; batteries are old/degraded. | Allow more time for batteries to charge; replace with new 18650 batteries. |
| Lamp charges but does not stay on in emergency mode. | Internal circuit issue. | Contact customer support. |
8. Specifications
| Feature | Detail |
|---|---|
| Brand | SHINEKNOT |
| Model | YJ805 |
| Wattage | 15W / 20W |
| Voltage | AC 200-240V |
| Light Source | LED (2835 Lamp Beads) |
| Color Temperature (CCT) | 8000-10000K (Cool White) |
| Battery Type | 2 x 18650 Lithium Battery (2400mAh) |
| Body Material | High-grade PC / PBT+PP |
| Certification | CCC, CE |
| Dimensions (H x D) | 160mm x 78mm |
| Warranty | 3 Years |
Figure 4: Internal components and features
Figure 5: Product dimensions and specifications table
9. User Tips
- Emergency Duration: Users report the lamp typically provides emergency lighting for approximately 2-3 hours on a full charge, depending on the wattage and battery condition.
- Brightness: The lamp shines very brightly, offering effective illumination during power outages.
- Light Color: The lamp emits a cool white light (around 6500K-10000K).
- Charging Time: The lamp charges automatically when installed in a powered socket. Ensure it's connected for several hours to fully charge the batteries.
10. Warranty and Support
This product comes with a 3-year warranty from the date of purchase. For warranty claims, technical support, or any inquiries, please contact your retailer or the manufacturer directly. Please retain your proof of purchase.