Introduction
This manual provides instructions for the COOSPO BK9 Bike Speed/Cadence Sensor. The BK9 sensor is a versatile device designed to accurately track your cycling speed and/or cadence, transmitting data via Bluetooth 5.0 and ANT+ protocols. It is compatible with various fitness applications and GPS bike computers, enhancing your training experience.
The COOSPO BK9 is available as a dedicated Cadence Sensor (BK9C) or a dedicated Speed Sensor (BK9S). This manual covers the installation and operation for both types, as they share similar core functionalities and setup procedures.
Package Contents
Please check the package for the following items:
- COOSPO BK9 Sensor (Main Unit)
- User Manual (this document)
- Silicone Pad (for mounting)
- Silicone Straps (for mounting)
Image: Two COOSPO BK9 sensors, one configured as a speed sensor and one as a cadence sensor.
Setup
1. Battery Activation
Before first use, you must activate the sensor's battery. Locate the battery compartment on the back of the sensor. Gently open the cover and remove the transparent insulation sheet (plastic tab) that prevents battery contact during shipping. Close the battery cover securely.
Note: A diagram in the original manual shows removing a transparent insulation sheet from the battery compartment. Ensure the battery is correctly oriented (+ and -) when closing the cover.
2. Mounting the Sensor
The COOSPO BK9 sensor can function as either a speed sensor or a cadence sensor, depending on its mounting location. The sensor automatically detects its function based on where it is installed.
Mounting as a Cadence Sensor (BK9C)
- Attach a silicone pad to the back of the sensor. Select a silicone strap appropriate for the thickness of your bicycle's crank arm.
- Install the sensor on the inner side of the left crank arm using the silicone strap.
- Rotate the crank arm to ensure the sensor and strap do not rub against any part of the bicycle frame or your shoes during cycling.
Image: A COOSPO sensor securely mounted on the inner side of a bicycle's crank arm, functioning as a cadence sensor.
Mounting as a Speed Sensor (BK9S)
- Attach a silicone pad to the back of the sensor. Select a silicone strap appropriate for the thickness of your bicycle's wheel hub.
- Install the sensor on the hub of either the front or rear wheel.
- Ensure the sensor is securely fastened and does not interfere with any moving parts of the wheel or fork/frame.
Image: A COOSPO sensor securely mounted on the hub of a bicycle wheel, functioning as a speed sensor.
Important:
- A blue indicator light will flash when the device is enabled.
- Ensure the sensor is installed firmly and does not touch or rub against any other part of the bicycle to prevent damage or loss during riding.
Operating Instructions
Pairing with Cycling Applications (Bluetooth)
The COOSPO BK9 sensor uses Bluetooth 5.0 for connectivity with various cycling applications.
- On your smartphone, enable Bluetooth and location services.
- Important: Do NOT pair the sensor directly through your phone's Bluetooth settings.
- Open your preferred cycling application (e.g., CoospoRide, Rouvy, Zwift, Peloton, Wahoo).
- Navigate to the sensor settings menu within the application. This is typically found under "More", "Settings", or "Devices".
- Look for an option to "Add Sensor" or "Add Device".
- The application will scan for available sensors. Locate the BK9 sensor's Bluetooth ID (e.g., "BK9C 12345" or "BK9S 67890") and select it to establish a connection.
Image: A smartphone displaying a sensor binding interface, alongside logos of compatible fitness applications.
Pairing with Smart Devices and GPS Bike Computers (Bluetooth and ANT+)
The COOSPO BK9 sensor supports both Bluetooth 5.0 and ANT+ for broad compatibility with bike computers and other smart devices.
- Ensure your smart device or GPS bike computer has Bluetooth and/or ANT+ enabled.
- Access the device's settings menu and select the option to "Add Sensor" or "Search for Sensors".
- The device will scan for nearby sensors. Identify the BK9 sensor by its Bluetooth or ANT+ ID and select it to connect.
Image: Two GPS bike computers displaying cycling data, indicating compatibility with ANT+ and Bluetooth sensors.
Sensor Status and Indicator Light
The sensor features an LED indicator light to communicate its status:
| Sensor Status | Indicator Light |
|---|---|
| Battery installed / Initial activation | Red and blue flash alternately |
| Wake up / Active | Blue light flashes |
| Low battery alert | Red light flashes |
Note on Pairing: The sensor will enter sleep mode after a period of inactivity. To wake it up before pairing, simply rotate the bicycle wheel (for speed sensor) or the crank arm (for cadence sensor).
Maintenance
Cleaning
The COOSPO BK9 sensor has an IP67 waterproof rating, meaning it is protected against dust and can withstand immersion in water up to 1 meter for 30 minutes. However, for cleaning:
- Wipe the sensor with a damp cloth.
- Do NOT soak the sensor in water.
- Avoid using high-pressure cleaning methods, as this may damage the device.
Image: A COOSPO sensor partially submerged in water, demonstrating its IP67 waterproof capability.
Battery Replacement
When the red light flashes, it indicates a low battery. Replace the CR2032 3V coin cell battery as follows:
- Gently open the battery compartment cover.
- Remove the old CR2032 battery.
- Insert a new CR2032 3V battery, ensuring the positive (+) side faces upwards.
- Securely close the battery compartment cover.
Refer to the "Battery Warnings" section for important safety information regarding batteries.
Troubleshooting
- Sensor not detected or connecting:
- Ensure the transparent insulation sheet has been removed from the battery compartment.
- Rotate the bicycle wheel or crank arm to wake up the sensor from sleep mode.
- Verify Bluetooth and location services are enabled on your phone or smart device.
- Ensure you are pairing through the cycling application or bike computer's sensor settings, not directly via the phone's Bluetooth settings.
- Check the battery level; replace if the red light is flashing.
- Inaccurate readings:
- Ensure the sensor is securely mounted and not moving during your ride.
- For cadence, ensure the sensor is on the inner side of the left crank arm.
- For speed, ensure the sensor is on the wheel hub.
- Some apps/devices may not register cadence below 30 RPM.
- General Device Malfunctions:
- Do not open or modify the product.
- Do not disassemble or attempt to repair this product yourself.
- If the product operates abnormally, contact COOSPO support.
- The product must be returned to the manufacturer for any service or repair.
Battery Warnings
Improper handling of batteries can lead to serious injury or death. Please observe the following precautions:
- Remove and immediately recycle or dispose of used batteries according to local regulations. Keep them out of reach of children.
- Even used batteries can cause severe injury or death. Contact your local poison control center for treatment information.
- Compatible battery type: CR2032. Nominal battery voltage: 3V.
- Do not force discharge, charge, disassemble, heat above 45°C (113°F), or incinerate batteries. This may cause chemical burns due to venting, leakage, or explosion.
- Ensure batteries are installed correctly according to polarity (+ and -).
- Do not mix new and old batteries, or batteries of different brands or types (e.g., alkaline, carbon-zinc, or rechargeable batteries).
- Remove batteries from devices that will not be used for an extended period and recycle or dispose of them according to local regulations.
- Always close the battery compartment securely. If the battery compartment cannot be closed firmly, stop using the product, remove the battery, and keep it out of reach of children.
Specifications
| Feature | Detail |
|---|---|
| Model | BK9 (BK9C for Cadence, BK9S for Speed) |
| Battery Type | CR2032, 3V |
| Battery Life | Approximately 300 hours (actual life depends on usage environment) |
| Wireless Transmission | Bluetooth 5.0; ANT+ |
| Waterproof Rating | IP67 |
User Tips
Based on user experiences, here are some helpful tips for using your COOSPO BK9 sensor:
- Compatibility: The BK9 sensor is widely compatible with various devices and apps, including Garmin (Edge series), iGPSport, Wahoo, Zwift, Rouvy, and Peloton. Users have reported seamless pairing with Garmin 530, 540, and 1000 models.
- Battery Tab: Always remember to remove the small plastic insulation tab from the battery compartment before first use to activate the sensor.
- Cadence Readings: Some devices or applications may not display cadence readings below approximately 30 RPM. This is normal behavior for many cycling sensors.
- Secure Mounting: The double-clip elastic band design provides a secure hold. Ensure the sensor is firmly attached to prevent it from dislodging during rides.
- Accuracy: When used as a speed sensor, it provides accurate readings even in areas where GPS signals might be weak, and some users note it can automatically recalibrate wheel size.
Warranty and Support
For more information, support, or warranty inquiries, please visit the official COOSPO website:
If your product is not functioning correctly, please contact COOSPO support directly. Any service or repair must be performed by the manufacturer.
This manual's content is for reference only. The product described may be subject to changes due to ongoing research and development by the manufacturer without prior notice. No statements or guarantees are made regarding this manual.
For a downloadable PDF version of the user manual, please refer to the official COOSPO website or the provided link: User Manual (PDF)