FENVI 1200Mbps Dual-Band WiFi Repeater Router User Manual

1. Introduction

Thank you for choosing the FENVI 1200Mbps Dual-Band WiFi Repeater Router. This device is designed to extend your existing Wi-Fi coverage, eliminate dead zones, and provide a strong, stable wireless signal throughout your home or office. It supports both 2.4GHz and 5GHz bands, offering high-speed connectivity for all your devices.

Image: FENVI 1200Mbps WiFi Repeater Router with key features highlighted.

2. Package Contents

• FENVI 1200Mbps Dual-Band WiFi Repeater Router
• Quick Installation Guide (this manual)
• Ethernet Cable (if applicable, not explicitly mentioned but common)

3. Product Overview

The FENVI WiFi Repeater Router features a compact design with integrated antennas and a standard plug for direct wall mounting. It includes several indicators and a button for easy operation.

3.1 LED Indicators

• Power LED: Indicates the device is powered on.
• 2.4G LED: Indicates the 2.4GHz Wi-Fi band is active.
• 5G LED: Indicates the 5GHz Wi-Fi band is active.
• Extender LED: Indicates the extender is successfully connected to the host router.

3.2 Buttons and Ports

• WPS Button: Used for quick setup with WPS-enabled routers. Also functions as a Reset button when pressed and held.
• LAN Port: (If present, common for AP mode, not clearly visible in main image but implied by "Wired Mode") Used for wired connections in AP mode or to connect a wired device.

Image: The device supports both EU and US standard plugs.

4. Setup Instructions

The FENVI WiFi Repeater Router supports multiple operating modes: Repeater (Extender) Mode and AP (Access Point) Mode. You can set it up using WPS or manually via a web browser.

4.1 WPS Quick Setup (Repeater Mode)

WPS (Wi-Fi Protected Setup) provides a simple way to extend your Wi-Fi network without manual configuration. Ensure your host router supports WPS.

1. Plug the FENVI WiFi Repeater into a power outlet near your host router. Wait for the Power LED to turn on.
2. Press the WPS button on your host router.
3. Within 2 minutes, press the WPS button on the FENVI WiFi Repeater.
4. Wait for the Extender LED on the FENVI Repeater to turn solid, indicating a successful connection. This may take a few moments.
5. Once connected, you can unplug the repeater and move it to a desired location within your router's Wi-Fi range.

Note: Your host router's SSID and Password will be used for the extended network. Special characters in the password might not be supported by WPS.

Image: WPS Quick Setup process.

4.2 Manual Setup via Web Browser (Repeater Mode)

This method allows for more control over the extended network settings. You can use either a PC or a mobile phone.

Image: The device offers strong wall penetration for extended coverage.

4.2.1 PC Setup Steps

1. Plug In: Plug the WiFi extender into a power outlet and wait for approximately 30 seconds.
2. Connect to Extender SSID: On your PC, connect to the extender's default Wi-Fi network (SSID). This will typically be named something like "wifi-5g-xxxx" or similar. Both 2.4G and 5G networks will be available; choose one to set up (e.g., 5G).

   Note: Turn off your mobile network data. You will not have internet access until setup is complete. If your computer prompts that the network cannot be connected, click to continue. If abnormal, reset the device by pressing and holding the WPS/Reset key for 8 seconds until the 2.4G and 5G lights are on.

3. Open Browser: Open a web browser (Google Chrome or Firefox recommended) and enter 192.168.188.1 in the address bar.

   Note: If access fails, ensure you are connected to the correct extender SSID.

4. Enter Password: Enter the default password: admin.
5. Scan and Select Host Router: The extender will scan for available Wi-Fi networks. Select your host router's SSID from the list. Both 2.4G and 5G can be extended; choose one at a time.
6. Enter Host Router Password: Enter the Wi-Fi password for your host router.

   Note: Ensure the password is correct. Special characters like spaces are not allowed.

7. Set Extender SSID and Password (Optional): You can choose to modify the extender's SSID and password. If you don't want to modify, proceed to the next step.
8. Confirm Information: Review the wireless information and click "Start Connect". Wait 30-60 seconds for the extender to connect to the router.
9. Connection Confirmation: Wait for the repeater to connect to the router successfully.
10. Indicator Lights: The "Extender" indicator light turning on means successful connection.
11. Reconnect: Reselect and reconnect your devices to the new extender Wi-Fi network (the new Wi-Fi name defaults to the original Wi-Fi name plus "-pro-2.4G" or "-pro-5G").

4.2.2 Mobile Phone Setup Steps

1. Plug In: Plug the WiFi extender into a power outlet and wait for approximately 30 seconds.
2. Connect to Extender SSID: On your mobile phone, connect to the extender's default Wi-Fi network (SSID). This will typically be named something like "wifi-5g-xxxx" or similar. Both 2.4G and 5G networks will be available; choose one to set up (e.g., 5G).

   Note: Turn off your mobile network data. You will not have internet access until setup is complete. If your phone prompts that the network cannot be connected, click to continue. If abnormal, reset the device by pressing and holding the WPS/Reset key for 8 seconds until the 2.4G and 5G lights are on.

3. Open Browser: Open a web browser and enter 192.168.188.1 in the address bar.

   Note: If access fails, ensure you are connected to the correct extender SSID and your phone's mobile data is off.

4. Enter Password: Enter the default password: admin.
5. Scan and Select Host Router: The extender will scan for available Wi-Fi networks. Select your host router's SSID from the list.
6. Enter Host Router Password: Enter the Wi-Fi password for your host router.

   Note: Ensure the password is correct. Special characters like spaces are not allowed.

7. Set Extender SSID and Password (Optional): You can choose to modify the extender's SSID and password. If you don't want to modify, proceed to the next step.
8. Confirm Information: Review the wireless information and click "Start Connect". Wait 30-60 seconds for the extender to connect to the router.
9. Connection Confirmation: Wait for the repeater to connect to the router successfully.
10. Indicator Lights: The "Extender" indicator light turning on means successful connection.
11. Reconnect: Reselect and reconnect your devices to the new extender Wi-Fi network (the new Wi-Fi name defaults to the original Wi-Fi name plus "-pro-2.4G" or "-pro-5G").

Image: Multi-Mode Application (Wireless and Wired).

Image: Extended network coverage up to 3000 sq ft.

5. Operating Modes

The FENVI WiFi Repeater Router can operate in two main modes:

5.1 Repeater/Extender Mode

In this mode, the device wirelessly connects to your existing router and extends its Wi-Fi signal to areas with weak or no coverage. This is the most common use case for eliminating Wi-Fi dead zones.

5.2 AP (Access Point) Mode

In AP mode, the device connects to your router via an Ethernet cable (wired connection) and then broadcasts a new wireless network. This is useful for adding Wi-Fi capability to a wired network or creating a new Wi-Fi hotspot.

6. Maintenance

• Keep the device in a dry place, away from water and moisture.
• Avoid exposing the device to extreme temperatures or direct sunlight.
• Do not block the ventilation holes on the device.
• Clean the device with a soft, dry cloth. Do not use liquid cleaners or aerosols.
• If the device is not functioning correctly, try resetting it to factory defaults by pressing and holding the WPS/Reset button for about 10 seconds until the LEDs flash.

7. Troubleshooting

7.1 No Internet Access After Setup

• Ensure the extender is successfully connected to your host router (Extender LED is solid).
• Verify that your host router has a working internet connection.
• Check if you entered the correct Wi-Fi password for your host router during setup.
• Try restarting both your host router and the FENVI Repeater.

7.2 Weak Signal or Frequent Disconnections

• Relocate the FENVI Repeater closer to your host router. It should be placed within the strong signal range of your router, not in a dead zone.
• Avoid placing the repeater near large metal objects, microwave ovens, or other devices that may cause interference.
• Ensure there are no physical obstructions (thick walls, floors) between the repeater and your devices, or between the repeater and the host router.

7.3 Cannot Access Web Management Page (192.168.188.1)

• Ensure your device (PC/phone) is connected to the FENVI Repeater's Wi-Fi network (its default SSID before setup, or its extended SSID after setup).
• Verify that you have typed the IP address correctly in the browser's address bar.
• Try using a different web browser.
• Temporarily disable any firewall or antivirus software on your computer.
• Reset the repeater to factory defaults and try again.

7.4 Resetting to Factory Defaults

If you forget your login password or encounter persistent issues, you can reset the device to its factory default settings:

1. With the device powered on, press and hold the WPS/Reset button for approximately 10 seconds.
2. Release the button when the LEDs flash.
3. The device will restart with factory default settings. You will need to reconfigure it.

8. Specifications

9. User Tips

• Easy Installation: Users have reported easy installation, especially when following the provided steps.
• Optimal Placement: For best results, place the extender roughly halfway between your router and the area where you need improved Wi-Fi. Avoid placing it in a Wi-Fi dead zone.
• Password Check: Double-check your main router's Wi-Fi password during manual setup to avoid connection issues.

10. Warranty and Support

For detailed warranty information and further technical support, please refer to the official product documentation or contact your retailer. A comprehensive user manual in PDF format may be available for download from the manufacturer's website or via the following link: FENVI WiFi Repeater User Manual (PDF).