Quansheng UV 5R Plus

Contents

Quansheng UV 5R Plus Walkie Talkie User Manual

Model: UV 5R Plus

1. Safety Information and Warnings

1.1 FCC FRS/GMRS/Amateur Warning

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

  • Reorient or relocate the receiving antenna.
  • Increase the separation between the equipment and receiver.
  • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
  • Consult the dealer or an experienced radio/TV technician for help.

This device complies with FCC radiation exposure limits set forth for an uncontrolled environment. Do not use this device when the antenna shows obvious damages. Hold this transmitter approximately 25 mm away from your face and speak normal with the antenna pointed up and away. Use the supplied belt clip for body-worn configuration as other accessories may not comply to the limits.

WARNING: MODIFICATION OF THIS DEVICE TO RECEIVE CELLULAR RADIOTELEPHONE SERVICE SIGNALS IS PROHIBITED UNDER FCC RULES AND FEDERAL LAW.

1.2 CE Warning

Use the two-way radio in an environment with temperatures between 0-40°C; otherwise, it may damage your two-way radio. It can be operated under 2000m.

Hereby, Quansheng declares that the radio equipment type two-way radio is in compliance with Directive 2014/53/EU. For this device, Head SAR and Body SAR were performed with the device configured in positions according to EN62209-2:2010, and face-up SAR was performed with the device 25mm from the phantom, and Body SAR was performed with the device 0mm from the phantom. Body SAR was also performed with the headset and belt clip attached and without.

1.3 Precautions Before Using

  • Please put the radio and accessories where children cannot reach.
  • Maintenance can only be performed by professional technicians.
  • Please use the standard battery pack and charger in order not to destroy the radio.
  • Please use the standard antenna, in order not to shorten the communication distance.
  • Do not expose the radio to sunlight for a long period of time, nor put it near heat.
  • Do not put it in extreme dust or wet environments.
  • Do not clean the radio with fierce chemical products, cleaning agents, or strong washing agents.
  • Do not transmit when the antenna is not installed.
  • If you find a bad smell or smoke, please turn off the radio immediately. Remove the battery and contact the agent.

1.4 Charging Notes

  • Battery packs are not charged when shipped. Charge them before use.
  • Initially charging the battery pack after purchase or extended storage (longer than 2 months) will not bring the battery pack to its greatest capacity or its normal charge, which can be achieved only after repeated charging and discharging two or three times.
  • Before charging, please power off the radio. Do not use the radio during charging, as it may affect normal charging and cause dangerous accidents.
  • After the battery pack is fully charged, please take it out of the charger-base. Do not charge it again before the battery is completely run out, or it will destroy the memory effect of the battery.
  • If the battery does not gain capacity or usage time even with correct charging, it means the battery life is near its end; please change to a new battery pack.
  • Please use the original factory battery pack and charger. They are available with your local agent.
  • If you have questions about non-original factory battery packs and accessories, please do not use them, as they may cause dangerous accidents.
  • Note: Use original factory charger for charging. To protect the environment, please recycle the battery pack. Never attempt to remove the casing from the battery pack.

2. Package Contents

Carefully unpack the portable radio. Please check that all the following items are included before discarding the packaging materials.

Item Quantity
Portable Radio 1
Antenna 1
Li-ion Battery 1
Battery Charger 1
Belt Clip 1
User's Manual 1
Quansheng UV 5R Plus Package Contents
Image: Quansheng UV 5R Plus Package Contents including radio, battery, charger, antenna, belt clip, and user manual.

3. Product Overview

3.1 Radio Diagram

Quansheng UV 5R Plus Radio Diagram
Image: Diagram of the Quansheng UV 5R Plus showing the antenna, jack light, power/volume switch, LCD screen, menu/confirm key, up/down key, exit key, keypad, speaker, microphone, transmitting key, side key 1, side key 2, and microphone/programming jacks.

Indicator Detail:

  • Red Light: Transmitting
  • Green Light: Receiving
  • Blue Light: On when Charging / Off when the radio is fully charged.

Power/Volume Switch: Turn on the radio by rotating clockwise; turn off by rotating counter-clockwise.

3.2 LCD Display

The LCD display provides visual feedback on the radio's status and settings. Below is a guide to the symbols you may see:

Quansheng UV 5R Plus LCD Display
Image: Close-up of the Quansheng UV 5R Plus LCD display showing frequency, channel, battery level, and various status icons.
Symbol Description
Signal Strength barsThe smaller the number of grids, the weaker the signal.
HMLTransmitting Output Power Indicator (High, Medium, Low).
CT DCSCTCSS/DCS code is active.
DVoice prompt is on.
NRadio operates in narrow band mode.
VOXVOX Function active. Transmission starts when sound pressure reaches set value.
+-Transmitting frequency equals receiving frequency plus/minus a frequency deviation.
DTMFDTMF signal decoding is on.
DWFrequency dual watch is on.
Keypad lock iconKeypad is locked.
Battery iconDisplay of current battery level. When nearly exhausted, it shows.
Main channel indicatorIndicates main channel. PTT on secondary channel initiates call on main channel.
SCRVoice encryption is on.
RReverse mode. Receive and transmit frequency reverse.
◆◆Scanning. Participating in scan list 1 or 2.
WXCross-Band Receiving/Transmitting.
RXReceiving.
TXTransmitting.
PC iconPC programming data cable connection.
AMAM receiving mark.
NSNOAA channel automatic scan.

3.3 Buttons and Keys

The Quansheng UV 5R Plus features several buttons and keys for various functions:

  • PTT Key (Transmitting Button): Press to transmit and speak into the microphone. Release to receive.
  • Programmable Function Keys (Side Keys):
    • Side Key 1 (Initial Function): Short press for Monitor function. Long press for 1750Hz.
    • Side Key 2 (Initial Function): Short press for Jacklight. Long press for emergency alarm.
    • Functions can be set via programming software: Emergency Mode On/Off, High/Low Output Power Selection, Monitor, FM Radio, Scan On/Off, VOX On/Off, Transmitting 1750, Jacklight.
  • Keypad Keys:
    • Menu/Confirm Key (MENU): Short press to enter the menu, select item, and confirm parameters. Long press to enter the last setting item. In DTMF function, it means 'A' code word.
    • Up Key (▲): Move upward in menus. In DTMF function, it means 'B' code word.
    • Down Key (▼): Move downward in menus. In DTMF function, it means 'C' code word.
    • Exit/Clear Key (EXIT): Short press to exit to upper menu; long press to exit to main page. In input status, clears input info. In DTMF function, it means 'D' code word.
    • * Key: Short press to enter manual dial/call page. In DTMF function, it means '*' code word. Long press to start frequency or channel scanning.
    • # Key: In DTMF function, it represents the '#' code word. Long press to lock or unlock the keypad.
    • F Key: Works with 0-9 for quick function switching. Long press to lock/unlock keyboard.

4. Setup

4.1 Initial Charging

Before first use, ensure the battery is fully charged using the provided charger. Refer to the 'Charging Notes' in Section 1.4 for detailed instructions.

4.2 Power On and Password Protection

To power on the radio, turn the Power/Volume Switch clockwise. If a Power On Password Protection is set, the screen will display "LOCK". You must input the password to use the radio normally.

4.3 Antenna and Battery Installation

Ensure the antenna is securely attached before transmitting. Install the Li-ion battery into the radio, ensuring it clicks into place. To remove the battery, follow the instructions in the user manual or contact support if unsure.

5. Basic Operation

5.1 Menu Navigation

Press the MENU key to enter Menu Selection. Use the Up/Down Keys to select a Menu Number. Press MENU again to confirm the selection. Press the EXIT key to return to the Upper Menu. Long press EXIT to return to the main page.

The menu offers various settings, including Squelch Level, Step Frequency, Output Power, DCS/CTCSS settings, Channel Bandwidth, Scrambler, and more. Refer to the full menu list in the PDF manual for all options.

5.2 Switching Main Channel

Press F+2 to switch the main channel. A solid arrow on the display indicates the main channel. Press PTT to transmit on the main channel.

5.3 Dual Band Single-Watch/Dual-Watch Switch

Dual-watch operation mode can be set via the menu (MENU → 17 → CHAN_A or CHAN_B). CHAN_A sets the default TX channel to A, and CHAN_B sets it to B. The screen will display "DW" when dual-watch is active.

5.4 Frequency/Channel Mode Switch

In the main page, press F+3 to switch between Frequency Mode (VFO) and Channel Mode (MR).

  • Frequency Mode: Manually input RX frequency or use Up/Down keys to adjust frequency by step. TX frequency cannot be directly input but can be changed via Frequency or Offset Frequency Direction settings in the menu.
  • Channel Mode: Displays the actual channel number. Manually input channel number or use Up/Down keys to switch channels.

5.5 Channel Save and Delete

  • Channel Save (MR Mode): In VFO mode, set RX Frequency, Frequency Deviation Direction, Wide/Narrow Bandwidth, RX/TX CTCSS/DCS, TX Output Power, Scanning participation, DTMF code, Scrambler, etc. Then, press MENU → 13 → CH-001, press MENU again, choose channel by Up/Down or Number Key, press MENU to confirm "SURE?" and save.
  • Channel Delete: Press MENU → 50 → CH-XXX, then press MENU again to enter Channel Delete. Choose the channel to delete by Up/Down Key or Keypad, press MENU to confirm "SURE?" and delete.

5.6 Receiving/Transmitting CTCSS/DCS Setting

CTCSS/DCS is used to remove unwanted noise signals during reception.

  • RX DCS Code: MENU → 4 → R-DCS.
  • RX CTCSS Code: MENU → 5 → R-CTCS.
  • TX DCS Code: MENU → 6 → T-DCS.
  • TX CTCSS Code: MENU → 7 → T-CTCS.

5.7 Fast Copy One Channel (Frequency Meter)

Quansheng UV 5R Plus Fast Copy One Channel
Image: Diagram illustrating the Fast Copy One Channel feature, allowing the radio to act as a frequency meter for two-way radios and other devices.

This function requires a strong signal and both transmitter and receiver to have antennas installed and be within reasonable distance.

  1. Press F+4 to enter Frequency Meter interface.
  2. When a strong signal is received, the LCD will display the signal carrier frequency and transmitting channel (CTCSS or DCS).
  3. Press * key to re-measure the frequency.
  4. After measuring, press MENU to save the frequency and CTCSS/DCS to a specified channel.
  5. During frequency measuring, press EXIT or PTT to exit.

First, set the correct receiving frequency. Press F+* to start channel searching. When a valid CTCSS/DCS signal is received, it will display the searched TX CTCSS/DCS signal. Press MENU to save it to the current channel.

  • If the screen displays "SCAN CMP", the radio has found a valid signal and stopped searching.
  • If the screen displays "SCAN FAIL", no valid signal was found.

5.9 DTMF Calling

  • Manual dialing: Press PTT and the Number key on the keypad.
  • Automatic calling: Press *, enter 3 digits, short press PTT. It automatically sends its own ID number.
  • Single call: Send the ID of the other party plus your own ID code (e.g., 123*100 for ID 100 to call ID 123).
  • Group call: Use a group calling code (set by program software) to call a communication group (e.g., send 12# to call radios with ID 120-129).
  • All call: Send ### group call TD to call all users.

5.10 PTTID

You can configure DTMF online and offline codes via program software. When enabled, the radio sends the online code when PTT is pressed and the offline code when PTT is released.

5.11 Scanning

Start Scanning:

  • Method 1: Long press * Key to start or exit scanning.
  • Method 2: Set a Side Key as Scanning Start/Close Switch.

Frequency Scanning: During scanning, change direction with Up/Down key. Press PTT or EXIT to exit.

Channel Scanning: Detects channels in the scan list. You can answer incoming calls by pressing PTT.

5.12 Emergency Alarm

Emergency Alarm is used for emergency situations. You can initiate calls anytime, on any screen, or even during channel activity. Users must configure the emergency alarm button via programming software.

  • Press the emergency alarm key to start a local audible alarm and send a remote alarm. The alarm type can be set as local alarm/remote alarm.
  • Exit alarm mode by any key.
  • Process: Press MENU → 34 → AL-MOD TONE (for alarm sound and remote alarm signal) or MENU → 34 → AL-MOD SITE (for alarm sound only).

5.13 FM Radio

Press F+0 to enter FM radio mode. Use Up/Down keys to change frequency or pre-stored FM channels. You can also use the keypad to enter FM frequency or channels.

  • Press F+1 to switch between VFO and MR mode.
  • Press F+2 to start automatic FM radio channel searching (stores up to 20 channels).
  • Press F+3 to start manual FM radio channel searching (users manually store channels).
  • MENU key stores FM channel; EXIT key exits searching; Up/Down keys switch scanning direction.
  • In FM Mode, if the radio receives calls or you press PTT, it temporarily exits FM Mode for communication, then returns to FM radio status.
  • Press EXIT or F+0 to exit FM Mode.

5.14 Emergency Weather Channel Receiving

Press F+5 to enter or exit NOAA Weather Alert. This radio can receive 10 NOAA channels. This mode can be set through Menu 49 NOAA_S.

5.15 Keypad Locking

Long press the # key to lock or unlock all keys on the keyboard. Side keys can still be used while the keypad is locked.

5.16 Reset

Process: Press MENU → 51 → RESET.

  • VFO: Resets only storage channels.
  • ALL: Resets all parameters, including storage channels. The LCD will display "Sure?". Press MENU and wait for the radio to restart. All menu settings will return to initial factory values.

5.17 One Key Call Channel

F+9 immediately jumps to a one-key call channel. You can set the important channel to one call channel by MENU → 30 → 1-call.

5.18 Aviation Band Receiving

Enter the receiving frequency. If the local aviation frequency is not clear, the scanning function can scan the 108-136 full frequency band.

  • Menu 48 → AM ON sets the channel modulation method to AM, for listening to aviation intercom.
  • Menu 48 → AM OFF sets the channel modulation method to FM.
  • Menu 48 settings are only valid for the 108-136 frequency band.

5.19 Wireless Radio Replication

Hold PTT + Side Key 2 to enter the Wireless Radio Replication interface. The LCD will display "Air Copy (RDY)". Both transmitting and receiving radios can use the digital keyboard to set the frequency of wireless replication. The frequencies must be consistent. The default receiving/transmitting frequency is 410.0125MHz.

  • Press EXIT key of the receiving radio to enter receiving mode; its LCD will display "Air Copy".
  • Press MENU key of the transmitting radio to start frequency data transmitting; its LCD will display "Air Copy".
  • During copy, the LCD displays copy progress (RCV:XX E:XX, where E:XX is the number of errors).
  • When copy is finished, the transmitter displays "SND: 120".

6. Maintenance

  • Cleaning: Do not use harsh chemicals, cleaning agents, or strong washing agents. Use a soft, damp cloth for cleaning.
  • Battery Care: Follow the charging notes in Section 1.4. Do not overcharge or fully discharge the battery repeatedly. Replace the battery if its capacity or operating time significantly decreases.
  • Storage: Store the radio in a dry environment, away from direct sunlight and extreme temperatures (0-40°C).
  • Professional Service: Any repairs or complex maintenance should only be performed by qualified technicians.

7. Troubleshooting

  • Radio not powering on or charging: Ensure the battery is properly installed and charged. Use the original charger. Check for any visible damage to the battery or radio.
  • No transmission or reception: Check antenna connection. Verify frequency and channel settings. Ensure PTT button is functioning. Check for keypad lock.
  • Poor sound quality or limited range: Ensure the antenna is the standard type and properly installed. Check for environmental interference. Adjust squelch level.
  • Radio emits bad smell or smoke: Immediately turn off the radio, remove the battery, and contact the seller or a qualified technician. Do not attempt to use the radio.
  • Battery not holding charge: The battery may be nearing the end of its life. Consider replacing it with an original factory battery pack.
  • Interference with other devices (radio/TV): Try reorienting or relocating the receiving antenna, increasing separation between equipment, or connecting to a different circuit. Consult a radio/TV technician if needed.

8. Specifications

8.1 General Specifications

Attribute Value
Channel200
Stored FM Radio Channel Quantity20
NOAA Channel10
Frequency Stability±1ppm
Modulation ModeFM: 11KΦF3E (12.5KHz), 16KΦF3E (25KHz)
Dimensions115mm*60mm*37.5mm
Weight234g
Operating Temperature-20°C to +60°C
Antenna Impedance50Ω
Output Power(w)3w-5w
Battery Capacity(mAh)2200
Waterproof / Water-ResistantNo
MaterialPlastic
Walkie Talkie TypePortable
Is_DisplayYes
Maximum Range3km-5km
OriginMainland China
CertificationCE, FCC, RoHS

8.2 Receiving Specifications

Frequency Range Sensitivity (FM: 12dB SINAD)
50-76 MHz-121dBm
108-135.9975 MHz-121dBm
136-173.9975 MHz-123dBm
174-349.9975 MHz-123dBm
350-399.9975 MHz-123dBm
400-469.9975 MHz-123dBm
470-599.9975 MHz-121dBm
WFM (76-108 MHz)-110dBm (20dB SINAD)
AM (108-135.9975 MHz)-113dBm (10dB S/N)
  • Audio Frequency: ≥0.5W
  • Audio Distortion: ≤10%

8.3 Transmitting Specifications

Attribute FCC Version CE Version Normal Version
Frequency RangeUHF: 420-450MHz, VHF: 144-148MHzUHF: 430-440MHz, VHF: 144-146MHzUHF: 400-470MHz, VHF: 136-174MHz, UHF: 350-400MHz
Output Power≤5W≤5W≤5W
Emission Current≤1.5A≤1.5A≤1.5A
Max Frequency Deviation≤5KHz (25KHz), ≤2.5KHz (12.5KHz)≤5KHz (25KHz), ≤2.5KHz (12.5KHz)≤5KHz (25KHz), ≤2.5KHz (12.5KHz)
Modulation Distortion≤5%≤5%≤5%
Stray Power≤7.5uW≤7.5uW≤7.5uW
Adjacent Channel Power70dB (25KHz), 60dB (12.5KHz)70dB (25KHz), 60dB (12.5KHz)70dB (25KHz), 60dB (12.5KHz)
Residual Modulation40dB40dB40dB

All stated specifications are subject to change without notice or obligation.

9. User Tips

  • Firmware Update: Some users have found enhanced functionality by flashing the radio with custom firmware like Egzumer. Proceed with caution and at your own risk.
  • Programming Software: When using programming software like Chirp, select the "Quansheng UV K5" model for compatibility.
  • Portability: The radio is noted for its small size, making it easy to carry in a pocket.
  • Sound Quality: Users generally report good sound quality for both transmission and reception.
  • Frequency Coverage: The device covers many frequencies and is highly programmable, offering versatility for amateur radio enthusiasts.
  • Battery Fit: Newer batches may have improved battery fit, making it more secure in the case.

10. Frequently Asked Questions (FAQ)

Q: Does this radio have scanning to hear people talk?
A: Yes, the Quansheng UV 5R Plus includes a scanning function (Section 5.11) that allows you to scan for active channels.
Q: Is the order for one radio or a set of two?
A: The standard package content (Section 2) lists "Portable Radio x1", indicating that a single radio is included per order unless specified otherwise by the seller.
Q: Which version of the radio is sent (e.g., v3 or older)?
A: Product versions can vary. One user reported receiving Version-4.00.07. For specific version inquiries, it is best to confirm directly with the seller at the time of purchase.

11. Warranty and Support

For detailed warranty information, please refer to the official user manual PDF provided by the manufacturer. A digital copy of the user manual is available at: User manual (PDF).

For technical support, troubleshooting assistance beyond this manual, or warranty claims, please contact the seller or authorized service center where you purchased the product.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.