SinoTrack ST-902

Contents

SinoTrack ST-902 OBD GPS Tracker User Manual

Model: ST-902 (ST-902L 4G)

1. Introduction

Thank you for choosing the SinoTrack ST-902 OBD GPS Tracker. This device is a plug-and-play vehicle tracking solution designed for real-time location monitoring, route playback, and various alerts. It connects directly to your vehicle's OBD-II port, making installation simple and quick. This manual provides detailed instructions for setting up, operating, and maintaining your GPS tracker.

2. Package Contents

Please check the box for the following items:

  • SinoTrack ST-902 OBD GPS Tracker
  • User Manual
SinoTrack ST-902 GPS Tracker, User Manual, and Packaging Box

Figure 2.1: SinoTrack ST-902 GPS Tracker, User Manual, and Packaging Box.

3. Specifications

FeatureSpecification
Model NameST-902 (ST-902L 4G)
Screen SizeNo screen
Battery Life1 to 4 Hours (Built-in)
Out Power0.02W
Voltage12 V
GPS ModuleYes
GPS TypeGPS Tracker
Special FeaturesInternet Connected
CertificationCE
Dimensions (Approx.)4 cm x 3.5 cm
SinoTrack GPS Tracker dimensions and features: Real-time Tracking, History Route playback, Leaving Alarm, Speeding Alarm, Shocking Alarm, Built-in Battery.

Figure 3.1: Device dimensions and key features.

4. Setup Guide

Follow these steps to set up your SinoTrack ST-902 GPS tracker:

4.1. SIM Card Preparation and Installation

  1. Choose a Micro SIM Card: The tracker requires a Micro SIM card. Ensure the SIM card does not have a PIN code enabled. If it does, disable it using a mobile phone before inserting it into the tracker.
  2. Insert SIM Card: With the tracker powered off, carefully insert the Micro SIM card into the designated slot on the device. Ensure it is inserted correctly.

Note: SIM card is not included. You need to purchase a local SIM card.

4.2. Device Installation

  1. Locate OBD-II Port: The ST-902 is a plug-and-play device designed to connect to your vehicle's OBD-II (On-Board Diagnostics II) port. This port is typically located under the dashboard on the driver's side, but its exact position can vary. Common locations include:
    • Under the steering wheel
    • Near the center console
    • Behind the ashtray
  2. Plug in the Tracker: Once located, simply plug the ST-902 GPS tracker firmly into the OBD-II port.
  3. Initial Power On: After plugging in, the device will power on automatically. The orange and blue LED lights on the tracker should light up, indicating it is starting up and attempting to connect to the network and acquire a GPS signal. Allow approximately 30 seconds for the device to initialize.
SinoTrack GPS Tracker being plugged into a vehicle's OBD-II port.

Figure 4.1: Plugging the tracker into the OBD-II port.

4.3. LED Status Indicators

The device has two LED indicators to show its status:

LED ColorStatusMeaning
Blue LED (GPS Status)FlashingNo GPS Signal or GPS starting
ON (Solid)GPS OK (Signal acquired)
Orange LED (GSM Status)FlashingNo SIM card or GSM starting
ON (Solid)GSM OK (Network connected)

4.4. Initial Configuration (SMS Commands)

To ensure proper online tracking, you may need to configure the APN (Access Point Name) and server IP/Port via SMS commands. Send these commands from your mobile phone to the SIM card number inserted in the tracker.

  1. Set APN:
    • Basic APN: Send SMS: 8030000 APN (Replace APN with your SIM card provider's APN. Example: 8030000 internet)
    • APN with Username/Password: If your APN requires a username and password, send SMS: 8030000 APN APNuser APNpassword (Example: 8030000 pp.vodafone.co.uk wap wap)

    Note: If you don't know your APN, contact your SIM card provider.

  2. Set Server IP and Port: (Default settings usually do not need to be changed)
    • Send SMS: 8040000 45.112.204.246 8090
  3. Set Control Number: To receive alarms and reports, set up to three control numbers.
    • Send SMS: Number+pass+blank+serial (Example: 139504434650000 1 where 13950443465 is your number, 0000 is default password, 1 is for the first control number).
Step-by-step setup guide for SinoTrack GPS Tracker: SIM card insertion, OBD2 port connection, LED lights, QR code scan, app download, and login details.

Figure 4.2: Visual guide for SIM card insertion, device connection, and app setup.

5. Operating Instructions

5.1. Tracking Methods

Your SinoTrack ST-902 offers multiple ways to track your vehicle:

  1. Website Tracking (PC Version):
    • Visit: Pro.SinoTrack.com
    • Login with your tracker's ID (found on the device) as the username and 123456 as the default password.
  2. Mobile Application Tracking:
    • Download the "SinoTrack PRO" app from the Apple App Store (iOS) or Google Play Store (Android).
    • Alternatively, scan the QR code provided in the manual or on the device packaging to download the app.
    • Login using your tracker's ID as the username and 123456 as the default password. Ensure the server is set to Pro.SinoTrack.
    SinoTrack tracking platform interface on laptop, tablet, and smartphone, with QR code and app download links.

    Figure 5.1: SinoTrack tracking platform across various devices.

  3. SMS Tracking:
    • By Dialing: Dial the SIM card number in the tracker from your mobile phone. The tracker will hang up and reply with an SMS containing a Google Maps link to its current location.
    • By Command: Send SMS: 669+password (e.g., 6690000 if default password is 0000). The tracker will reply with an SMS containing a Google Maps link.

5.2. Working Modes

The ST-902 supports two working modes:

  • SMS Mode (Default): For control via mobile phone and receiving Google location links via SMS.
    • To set SMS Mode: Send SMS: 700+Password (e.g., 7000000)
  • GPRS Mode: For real-time online tracking via the website or mobile app. This is recommended for continuous monitoring.
    • To set GPRS Mode: Send SMS: 710+Password (e.g., 7100000)

5.3. Advanced SMS Commands (Functions)

You can configure various features of your tracker by sending specific SMS commands to its SIM card number. The default password is 0000.

FunctionCommand (Example with default password 0000)Description
Change Password777NewPassOldPass (e.g., 77712340000)Changes the device password.
Change Time Zone896PassE/W+HH (e.g., 8960000E00 for GMT+0)Sets the time zone (E for East, W for West, HH for hours offset).
Scheduled Location Report665PassHHMM (e.g., 66500001219 for 12:19 daily)Sends location to the first control number at a specified time daily. To turn off: 665PassOFF.
Geo-Fence (Open/Close)Open: 211Pass (e.g., 2110000)
Close: 210Pass (e.g., 2100000)
Enables/disables the geo-fence alarm.
Set Geo-Fence Radius005PassRadius (e.g., 00500001000 for 1000 meters)Sets the radius of the geo-fence in meters.
Over Speed Alarm122PassXXX (e.g., 1220000120 for 120 KM/H)Sets the speed limit for an alarm. XXX is speed in KM/H (0 to 999). 0 disables the alarm.
Mileage (Set/Read)Set: 142PassMValue (e.g., 1420000M1000)
Read: 143Pass (e.g., 1430000)
Sets initial mileage or reads current total mileage (in meters).
Shock Alarm (Open/Close)Open: 181PassT (e.g., 1810000T10 for 10s)
Close: 180Pass (e.g., 1800000)
Enables/disables the shock alarm. T is shocking time in seconds (0-120).
Call Mode (On/Off)On: 150Pass (e.g., 1500000)
Off: 151Pass (e.g., 1510000)
When ON, alarms will call and send SMS. When OFF, only SMS.
Sleep Mode (Open/Close)Open: SLEEPPass1 (e.g., SLEEP00001)
Close: SLEEPPass0 (e.g., SLEEP00000)
Enables/disables sleep mode. Tracker sleeps when vehicle stops for 5 minutes.
Set Time Interval (GPRS Upload)805PassT (e.g., 805000020 for 20 seconds)Sets the GPRS data upload interval in seconds (10-18000). T=0 closes GPRS.

Note: Always replace "Pass" with your current device password. Default is 0000.

6. Maintenance

To ensure the longevity and optimal performance of your SinoTrack ST-902 GPS tracker, please follow these general maintenance guidelines:

  • Keep Dry: Avoid exposing the device to water, moisture, or extreme humidity, as this can damage internal components.
  • Avoid Extreme Temperatures: Do not store or operate the device in very hot or very cold environments.
  • Clean Gently: If cleaning is necessary, use a soft, dry cloth. Do not use harsh chemicals, cleaning solvents, or strong detergents.
  • Secure Connection: Ensure the device is securely plugged into the OBD-II port to prevent accidental disconnections.
  • Avoid Physical Damage: Protect the device from drops, impacts, or excessive vibration.

7. Troubleshooting

If you encounter issues with your SinoTrack ST-902, try the following troubleshooting steps:

  • Device Not Online / No Tracking Data:
    1. Check SIM Card: Ensure the Micro SIM card is correctly inserted, active, has sufficient balance/data, and does not have a PIN code enabled.
    2. Check APN Settings: Verify that the APN is correctly configured for your SIM card provider. Send the RCONF command to the tracker to check its current settings.
    3. Check Server IP/Port: Ensure the server IP and port are correctly set (default: 45.112.204.246 8090). Use RCONF to verify.
    4. Check Working Mode: Confirm the device is in GPRS mode for online tracking (send 7100000 if needed).
    5. Check LED Indicators: Refer to Section 4.3 to interpret the Blue (GPS) and Orange (GSM) LED statuses. Ensure both are solid ON for proper operation.
    6. Restart Device: Unplug the device from the OBD-II port, wait a few seconds, and plug it back in. You can also send the SMS command RESTART.
  • Incorrect Location / Location in China:
    1. GPS Signal: Ensure the vehicle is in an open area with a clear view of the sky to acquire a strong GPS signal.
    2. Time Zone: Configure the correct time zone using the SMS command (e.g., 8960000E00 for GMT+0).
    3. APN: Incorrect APN settings can sometimes affect location data. Double-check your APN configuration.
  • Login Error (ID + Default Password 123456):
    1. Verify ID: Ensure you are entering the correct 10-digit ID printed on the tracker.
    2. Default Password: The default password is 123456 for the app/website. If you changed the SMS command password, it does not affect the app/website login unless explicitly linked.
    3. Server Selection: For the mobile app, ensure the server is selected as Pro.SinoTrack.
    4. Contact Support: If the issue persists, contact SinoTrack support.
  • Device Not Responding to SMS Commands:
    1. SIM Card: Check if the SIM card has credit and can receive SMS.
    2. Password: Ensure you are using the correct password in your SMS commands.
    3. Format: Double-check the SMS command format for any typos or incorrect spacing.

For a full diagnostic report, send the SMS command RCONF to the tracker. It will reply with its current configuration.

8. User Tips

Here are some tips from other users to enhance your experience with the SinoTrack ST-902:

  • SIM Card Choice: Always use a Micro SIM card from a reliable provider with good network coverage in your area. Ensure it has data and SMS capabilities.
  • APN Accuracy: The most common setup issue is an incorrect APN. Double-check with your SIM provider for the exact APN, including any username/password if required.
  • Initial Testing: After installation, test the tracking functions (app, website, SMS) in an open area to confirm GPS signal acquisition and network connectivity.
  • Password Security: Change the default password for SMS commands (0000) to a strong, unique password for security.
  • Battery Life: While the device draws power from the OBD port, it has a small internal battery for backup. If the vehicle is off for extended periods, the internal battery will drain.

9. Frequently Asked Questions (FAQ)

Q: What type of SIM card does it use?
A: It uses a Micro SIM card. Ensure it has no PIN code enabled.
Q: Does it work on 2G and 4G networks?
A: The ST-902L model supports 4G networks, which are backward compatible with 2G/3G. Ensure your SIM card and network provider support the necessary bands.
Q: I'm getting a login error with the default password. What should I do?
A: Ensure you are using the tracker's ID as the username and 123456 as the password for the app/website. Also, confirm the server is set to Pro.SinoTrack. If you changed the SMS password, it does not affect the app/website login unless you specifically changed it there too.
Q: The tracker shows my location in China. How can I fix this?
A: This usually indicates a problem with GPS signal acquisition or time zone settings. Ensure the vehicle is in an open area, and configure your correct time zone via SMS command (e.g., 8960000E00 for GMT+0, adjust HH for your offset).
Q: Will it work with my car (e.g., Ford Kuga UK)?
A: The ST-902 is designed to work with any vehicle equipped with a standard 16-pin OBD-II port, which is common in most cars manufactured after 1996 (in the US) or 2001 (in Europe). Check your vehicle's manual or consult a mechanic if you are unsure about your car's OBD-II compatibility.

10. Support and Warranty

For further assistance, technical support, or warranty inquiries, please refer to the following:

  • Full User Manual (PDF): A detailed PDF user manual is available for download. You can access it via the seller's product page or by scanning the QR code provided with your device. (Reference: SinoTrack ST-902 User Manual PDF)
  • Email Support: For order-related support or technical issues, you can contact SinoTrack directly via email: sino@sinotrack.com.

Please provide your device ID and a detailed description of the issue when contacting support for faster resolution.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.