ZOOM HB-775E

Contents

ZOOM HB-775E E-BIKE Hydraulic Disc Brake Set User Manual

Model: HB-775E

Introduction

This manual provides essential instructions for the installation, operation, and maintenance of your ZOOM HB-775E E-BIKE Hydraulic Disc Brake Set. Please read it thoroughly before use to ensure safe and optimal performance.

General Safety Warnings

  • High Temperature: The caliper body and disc can reach high temperatures during braking. Avoid touching these parts immediately after riding to prevent burns. Allow them to cool sufficiently before any maintenance.
  • Braking Distance: Braking distance increases significantly in wet conditions. Reduce speed and apply brakes cautiously when riding in the rain.
  • Tire Skid Risk: Wet road surfaces increase the risk of tire skidding and falls. Exercise caution and reduce speed.
  • Brake System Check: Always ensure the brake system is functioning correctly before each ride.
  • Oil Contamination: Prevent oil from contaminating the disc and brake blocks, as this can lead to brake failure. If brake blocks are contaminated, replace them. If the disc is contaminated, clean it thoroughly.
  • Brake Block Thickness: Ensure brake block thickness is greater than 0.8mm before riding. Replace worn brake blocks immediately (refer to Figure 2-7 in the full PDF manual for replacement marks).
  • Brake Fluid: Use only ZOOM mineral oil (compatible with Shimano and Yannao mineral oil). Using other brake fluids can cause brake failure, air lock, or system damage.

Cautions for Use

  • Air Lock Phenomenon: Heating of brake fluid can cause water or air bubbles to expand, leading to piston protrusion and sudden brake action. Always use fresh, sealed brake oil and avoid mixing water or air.
  • Avoid Frequent Braking: Frequent braking can lead to air lock.
  • Inverted Vehicle: The ZOOM system is not designed for inverted operation. If the vehicle is inverted or horizontal for an extended period, micro-bubbles may form in the brake system, potentially causing brake failure. After such an event, hold the disc brake handle to confirm normal operation before riding.
  • Oil Leakage: If oil leakage occurs, stop using the brakes immediately and seek repair. Continuing to ride with oil leakage is dangerous.
  • Quick Release Handle: Ensure the quick release handle is on the side opposite to the disc to prevent collision.
  • Component Compatibility: Use only ZOOM original parts for optimal performance.
  • Fasteners: Regularly check screws and nuts for tightness. Loose fasteners can lead to accidents.

Mineral Oil Handling

  • Eye Contact: Wear safety glasses. If oil enters eyes, wash immediately with clean water and seek medical attention.
  • Skin Contact: Wear protective gloves. If oil touches skin, wash thoroughly with soapy water.
  • Inhalation: Ensure good ventilation.
  • Ingestion: Do not drink mineral oil.
  • Storage: Keep out of reach of children.
  • Waste Oil: Dispose of waste oil according to local regulations.
  • Storage Method: Store in a sealed, dark, and low-temperature place, away from direct sunlight and moisture.

Package Contents

Your ZOOM HB-775E Hydraulic Disc Brake Set includes the following components:

ZOOM HB-775E Hydraulic Disc Brake Set components

Image: All components of the ZOOM HB-775E Hydraulic Disc Brake Set, including levers, calipers, cables, and mounting hardware.

  • Hydraulic Brake Levers (Left and Right)
  • Hydraulic Brake Calipers (Front and Rear)
  • Pre-filled Hydraulic Hoses
  • Mounting Bolts and Accessories
  • Power-off Cables (integrated with levers)

Specifications

Feature Detail
Model Number HB775E
Type Hydraulic Disc Brake
Braking System Hydraulic Disc Brake (Hydraulic Brake Pad)
Hose Length Options 1100mm / 1850mm (depending on variant)
Power-off Cable Length 45mm
Brake Lever Length 90mm
Handlebar Clamp Diameter 22.2mm
Brake Pad Dimensions 32.5mm x 27mm
Piston Material Steel
Caliper Design Integrated Cast Caliper
Origin Mainland China
Brake lever dimensions and adjustment

Image: Detailed view of the brake lever, showing 90mm length, 22.2mm handlebar clamp diameter, and the brake stroke adjustment screw.

Brake pad dimensions and compatibility

Image: Brake pad dimensions (32.5mm x 27mm) and a list of compatible brake models.

Steel piston and integrated cast caliper

Image: Close-up showing the durable steel piston and the stable integrated cast caliper design.

Compatible Brake Pads

The HB-775E brake system is compatible with brake pads designed for the following models:

  • SHIMANO XT/R M975/M966/M965, SAINT M800
  • XT M775/M776/M765, M665, HONE M601
  • LX M585, DEORE M596/M595/M545/M535/M505
  • BR-R505/BR-S501/BR-S500/BR-T665/BR-T605
  • ZOOM HBIOO HB870 HB875 HB775

Setup and Installation

1. Disc Installation

  1. Install the disc on the flower drum, ensuring the ZOOM logo on the disc faces outward (rotation direction consistent with the wheel's arrow).
  2. Loosely fasten the disc fixing screws.
  3. Wear protective gloves. Apply force to the disc clockwise and then lock the disc fixing screws in a diagonal order.
  4. The locking torque for disc fixing screws is 40-60kgf-cm (35-52lb-in).

2. Caliper Body Assembly

  1. Install the front or rear disc brake conversion seat onto the screw hole of the support.
  2. Loosen the caliper body fixing screws to allow for fine-tuning.
  3. Install the conversion seat onto the frame.

3. Disc Handle Assembly

  1. Fix the disc handle first. Loosely fasten one screw, then tighten the other, and finally tighten the first screw.
  2. The locking torque for the disc brake handle is 60-80kgf-cm (52-69lb-in).
  3. Hold the disc handle under pressure and lock the disc caliper body fixing screws when the disc is pressed by the disc block.
  4. Pump the brake handle several times to confirm normal brake action and absence of oil leakage.
  5. The locking torque for the transfer seat fixing screw is 70-90kgf-cm.

4. Tubing Cutting (if necessary)

If the pre-installed oil pipe length is too long for your bicycle, it must be cut and adjusted. The power-off cable has a length of 45mm (see image below).

Power-off cable length 45mm

Image: Close-up of the power-off cable connector, indicating a cable length of 45mm.

Necessary Tools and Parts:

  • 8mm open-end wrench
  • Oil pipe joint screw
  • Tubing cutting tool
  • Oil pipe hold-down nut
  • Tubing copper sleeve
  • Oil needle

Operation Steps:

  1. Push the oil pipe fixing screw sheath towards the oil pipe. Use an 8mm open-end wrench to unscrew the oil pipe fixing screw. Be mindful of brake oil leakage.
  2. Determine the required oil pipe length and cut off the excess (at least 15mm) with the tubing cutting tool. Ensure the cut is vertical to the oil pipe axis.
  3. Insert the oil pipe, copper sleeve, and oil pipe bushing (with type ring) in sequence. Ensure the smaller end of the copper sleeve is fixed to the oil pipe.
  4. Press the front end of the oil pipe into the front end of the disc handle until it reaches the bottom. While pressing the oil pipe, lock the oil pipe fixing screw on the disc handle with an 8mm open-end wrench.
  5. The locking torque for the oil pipe fixing screw is 80-100kgf-cm (6-10NM).

5. Oil Replenishment Operation

Oil replenishment is necessary if the oil level in the oil groove is insufficient or if the brake block is worn, making it impossible to firmly hold the disc brake handle.

Necessary Tools and Parts:

  • T15 M-shaped wrench
  • 8mm open-end wrench
  • Oil needle cylinder
  • Transparent hose
  • Oil storage bottle
  • ZOOM mineral oil

Operation Steps:

  1. Position the oil groove parallel to the ground. Remove the sealing screw of the oil groove with a T15 M-shaped wrench.
  2. Insert the transparent hose into the upper end of the M6 oil nozzle and connect the other end to the plastic hose.
  3. Draw an appropriate amount of vehicle oil from the oil storage tank with the transparent hose connected to the oil needle cylinder. Ensure no bubbles are in the hose.
  4. Insert the oil needle cylinder into the upper body oil inlet nozzle.
  5. Use an 8mm open-end wrench to tighten the loading body oil inlet nozzle (clockwise for about 1.5 turns).
  6. Formal Oil Replenishment: Press the brake handle by hand until no bubble is discharged from the needle cylinder hose. If the effect is not obvious, press the needle cylinder by hand to make the brake oil enter the disc brake, then pull the needle cylinder to discharge the bubble. Repeat this action three to five times. Then press and release the brake handle until no bubble is discharged from the needle cylinder hose.
  7. Remove the needle cylinder, put the oil nozzle at the main end, and lock the oil injection screw.
  8. Hold the disc brake handle several times to ensure a solid grip.
  9. Remove the hose at the end of the caliper body, being careful not to stain the brake block or disc with brake oil. Then remove the hose at the handle end and replace the M6 oil nozzle with the oil groove sealing screw.
  10. The locking torque for the oil groove sealing screw is 30-40kgf-cm.
  11. Clean any oil-stained parts with alcohol or a clean cloth. Return the disc brake handle to its original position.
  12. If the oil in the oil tank changes color significantly, it is recommended to replace all the oil.

Operation and Adjustments

1. Adjustment of Brake Block and Disc Brake Caliper Body

The ZOOM disc brake system automatically adjusts the clearance between the disc and brake block as the brake blocks wear. When replacing brake blocks, the piston must be pressed vertically to the bottom with a slotted screwdriver.

If the piston moves unevenly or the brake block interferes with the disc, refer to the brake block replacement steps (Figure 2-5 in the full PDF manual).

2. Adjustment of Hand Grip Distance

If the grip distance is too large or too small, or if temporary increased braking force is needed, use the micro-adjustment function via the connecting adjustment screw on the disc brake handle.

  • Using a 2mm hex wrench, turn clockwise to increase grip distance (maximum ~100mm).
  • Turn counter-clockwise to decrease grip distance (minimum ~80mm).
  • If adjusting clockwise to the maximum (100mm) and turning the 2mm hex wrench further, the aluminum piston will move forward, making the handle easier to press (increasing braking force). Note that this may invalidate the automatic oil replenishment function.

Maintenance

To ensure long-term optimal performance of your ZOOM hydraulic disc brake system, perform the following inspections:

Before Riding

  • Brake Block Thickness: Confirm that the brake block thickness is above the 0.8mm limit. If worn, replace with new brake blocks.
  • Tubing Check: Inspect the oil pipe for cracks, wear, or damage. Replace the oil pipe if any issues are found.

After Riding

  • Disc Cleaning: If dirt or impurities are present between the disc brake caliper body and the disc, clean them after riding. Avoid contaminating the disc or brake blocks with any oil.

Periodic Inspection

  • Disc Brake Handle Lubrication: Regularly lubricate the connecting rod of the disc brake handle with lubricating oil.
  • Locking Screws: Check that all screws are tight and maintain the originally set locking torque.

Troubleshooting

Refer to the table below for common problems and their solutions:

Problem Possible Causes Solution
Friction between brake block and disc Incorrect adjustment of brake block or caliper body Readjust the brake block or caliper body (refer to Chapter 3)
Holding distance of disc brake handle is too large Poor grip Adjust the grip distance (refer to Chapter 3)
Disc deformation or bending Damaged disc Replace the disc (refer to Chapter 2)
Air exists in the system Air in the brake fluid Loosen the oil groove sealing screw and pump the handle several times to exhaust air. Supplement brake oil if necessary (refer to Chapter 5)
The transfer seat is loose Loose fixing screws Lock the fixing screws of the adapter (refer to Chapter 2)
The disc brake handle can be pressed to the driver's handle Insufficient brake oil Supplement brake oil (refer to Chapter 5)
Oil leakage Damaged seal or hose Check the oil leakage part and repair or replace it
Insufficient or no braking force Brake block polluted or contaminated Thoroughly clean and dry the discs with alcohol, and replace the brake blocks.

User Tips

  • The adjustable levers make it easier for users with smaller hands to operate the brakes effectively.
  • The hydraulic system provides a smooth and easy pull, allowing for strong braking with minimal effort.
  • If the pre-filled hoses are too long for your bike, they can often be coiled and secured in a hidden location without needing to be cut, provided there is no interference with moving parts.
  • Installation is generally straightforward, and many users find it easy to assemble by following instructions or online guides.

Frequently Asked Questions (FAQ)

Q: What is the part number for replacement brake pads?
A: The HB-775E system is compatible with brake pads for SHIMANO XT/R M975/M966/M965, SAINT M800, XT M775/M776/M765, M665, HONE M601, LX M585, DEORE M596/M595/M545/M535/M505, BR-R505/BR-S501/BR-S500/BR-T665/BR-T605, and ZOOM HBIOO HB870 HB875 HB775. Please check with your retailer or the manufacturer for specific part numbers for these compatible models.
Q: What type of oil is used in these brakes?
A: This system uses ZOOM mineral oil. It is compatible with Shimano and Yannao mineral oil.
Q: Does this brake set fit specific e-bike models like Ouxi V20, H9, or V8?
A: Compatibility depends on the specific frame design, rotor size, and mounting type of your e-bike. Please compare the specifications and dimensions provided in this manual with your bike's requirements before purchase or installation. Professional installation is recommended if you are unsure.

Warranty & Support

The effective shelf-life period for this product is one year under normal use conditions. Natural wear and aging of components are not covered by warranty.

For more detailed instructions, diagrams, and support, please refer to the official user manual PDF:

View User Manual (PDF)

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.