Dynoracing 637X-7

Contents

Dynoracing 2" (52mm) High Speed Car Gauges

Instruction Manual

Introduction

This manual provides detailed instructions for the installation, operation, and maintenance of your Dynoracing 2-inch (52mm) High Speed Car Gauges. These gauges feature a high-speed stepper motor for accurate readings and a 7-color selectable backlight for enhanced visibility and customization.

Available gauge types include:

  • Boost/Vacuum Gauge
  • Water Temperature Gauge
  • Oil Temperature Gauge
  • Oil Pressure Gauge
  • Air Fuel Ratio Gauge
  • Voltmeter
  • Exhaust Gas Temperature (EGT) Gauge
  • Tachometer (RPM) Gauge
Collection of Dynoracing 52mm gauges including boost, RPM, A/F ratio, volts, oil temp, EGT, water temp, and oil pressure.
Figure 1: Various Dynoracing 52mm Gauge Types

Setup and Installation

1. Mounting

The Dynoracing gauges are designed for a standard 52mm (2-inch) mounting hole. Ensure sufficient depth is available behind the mounting surface for the gauge body and wiring connections.

Diagram showing the dimensions of the gauge: 52mm diameter, 53mm height, 58mm base width.
Figure 2: Gauge Dimensions

2. Electrical Wiring

Refer to the wiring diagram below for specific connections for each gauge type. Always ensure the vehicle's battery is disconnected before performing any electrical work.

Detailed electrical wiring diagrams for various Dynoracing gauges.
Figure 3: Electrical Gauge Installation Instructions

General Wiring Guidelines:

  • RED Wire: Connect to Ignition Switch 12V(+) (switched power).
  • BLACK Wire: Connect to Battery(-) (ground).
  • YELLOW Wire: Typically for backlight or specific sensor input (refer to specific gauge instructions).
  • GREEN Wire: Typically for sensor signal input.

Specific Gauge Wiring:

Gauge TypeConnections
Boost/Vacuum GaugeRED to Ignition 12V(+), YELLOW to Ignition 12V(+), BLACK to Battery(-), GREEN to Sensor, Connect Nylon Tubing.
Oil/Water Temperature GaugeRED to Ignition 12V(+), YELLOW to Ignition 12V(+), BLACK to Battery(-), GREEN to Sensor.
Oil Pressure GaugeRED to Ignition 12V(+), YELLOW to Ignition 12V(+), BLACK to Battery(-), GREEN to Pressure Sensor.
Voltmeter GaugeRED to Ignition 12V(+), YELLOW to Ignition 12V(+), BLACK to Battery(-).
Tachometer GaugeYELLOW to Ignition 12V(+), BLACK to Battery(-), GREEN to Sensor (Coil/Distributor). Includes SET buttons for backlight color and cylinder settings (1-8).
Air Fuel/Ratio GaugeRED to Ignition 12V(+), YELLOW to Ignition 12V(+), GREEN to O2 Sensor Signal Wire, BLACK to Battery(-).
Exhaust Gas Temperature (EGT)RED to Ignition 12V(+), YELLOW to Ignition 12V(+), BLACK to Battery(-), ORANGE to ORANGE (Sensor), GREEN to GREEN (Sensor).

3. Sensor Installation

Install the appropriate sensor for your gauge type (e.g., temperature sensor into a coolant line, pressure sensor into an oil gallery, O2 sensor for AFR, EGT probe into exhaust manifold). Ensure all sensor connections are secure and leak-free.

Operating Instructions

1. Power On/Off

The gauges will power on automatically when the vehicle's ignition is turned to the 'ON' or 'ACC' position, provided they are wired correctly to a switched 12V source. They will power off when the ignition is turned off.

2. Reading the Gauge

Once powered on, the gauge needle will sweep to its maximum position and return to zero (self-test) before displaying the current reading. Read the value indicated by the needle on the gauge face.

3. Changing Backlight Color

Your Dynoracing gauge features a 7-color selectable backlight. To change the color, locate the small button on the back or side of the gauge (or as indicated in the tachometer diagram, use the 'SET' button). Press this button repeatedly to cycle through the available colors until your desired color is displayed.

Water temperature gauge displaying 7 different backlight colors: yellow, red, green, white, purple, blue, and light blue.
Figure 4: 7-Color Backlight Demonstration
Video 1: Dynoracing Gauge Color Change Demonstration

Maintenance

  • Cleaning: To clean the gauge face and body, use a soft, dry, lint-free cloth. Do not use abrasive cleaners or solvents, as these may damage the display or finish.
  • Wiring Inspection: Periodically check all wiring connections to ensure they are secure and free from corrosion or damage.
  • Sensor Inspection: For gauges with external sensors (e.g., temperature, pressure, EGT), periodically inspect the sensor and its connections for any signs of wear, damage, or leaks.

Troubleshooting

ProblemPossible CauseSolution
Gauge does not power onNo power to RED wire, poor ground connection (BLACK wire), or faulty ignition switch connection.Check RED wire for 12V with ignition on. Ensure BLACK wire has a solid ground. Verify ignition switch connection.
Incorrect or no readingSensor not connected, faulty sensor, incorrect sensor type, or wiring issue to sensor. For Boost/Vacuum, check tubing. For Tachometer, check cylinder setting.Verify sensor is correctly installed and wired. Test sensor if possible. Ensure correct sensor is used for the gauge. Check for loose or damaged wires.
Backlight not working or flickeringPoor connection to YELLOW wire (if applicable), internal wiring issue, or faulty backlight LED.Check YELLOW wire connection. Ensure all connections are secure.
Inconsistent or erratic readingsLoose wiring connections, electrical interference, or a failing sensor.Inspect all wiring for secure connections. Ensure proper grounding. Consider testing or replacing the sensor.

Specifications

FeatureSpecification
Gauge Diameter52mm (2 inches)
MaterialABS + Steel + Glass
Item Weight0.3KG - 0.5KG (approx.)
Special FeaturesHigh Speed Stepper Motor, 7-Color Backlight
Operating Voltage12V DC
Boost/Vacuum Range-30 IN.HG to 25 PSI (or 0 to 2 BAR)
Tachometer Range0 to 10 RPM (x100)
Voltmeter Range8 to 18 VOLTS
Oil Temperature Range50 to 140 °C
EGT Range6 to 13 (x100 °C)
Water Temperature Range40 to 140 °C
Oil Pressure Range0 to 100 PSI (or 0 to 7 BAR)

User Tips

  • The multi-color backlighting is a popular feature; experiment with different colors to find what best suits your vehicle's interior or your preference.
  • The pre-installed wires on the gauge harness can simplify installation. If extending sensor wires, ensure you use appropriate gauge wiring to maintain signal integrity.
  • Always double-check sensor functionality after installation. If readings appear incorrect, verify the sensor connection and consider testing the sensor itself.
  • For specific gauge types like EGT and Air/Fuel Ratio, confirm that the necessary sensors are included with your purchase.

Warranty and Support

For any warranty claims, technical support, or inquiries regarding your Dynoracing gauges, please contact your original seller or the manufacturer directly. Please have your purchase details and model number (637X-7) ready when contacting support.

A detailed user manual in PDF format may also be available for download. Please refer to the seller's product page or contact them for access to the PDF manual: User Manual (PDF).

© 2023 Dynoracing. All rights reserved.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.