1. Introduction
The AZDOME Hardwire Kit is designed to provide a continuous power supply to your dash cam or other car electronic devices, enabling features like 24-hour parking monitoring and protecting your vehicle's battery from discharge. This kit converts your car's 12V or 24V power to a stable 5V/2.5A output, ensuring reliable operation of your device.
It features high compatibility with various devices and includes low voltage protection to prevent your car battery from being drained below the necessary starting voltage.
2. Safety Information
- Always ensure your vehicle's engine is off before beginning installation.
- If you have no experience in installing car electrical components, please consult a professional to avoid damage to your vehicle or the product.
- Ensure all connections are secure to prevent short circuits or power interruptions.
- The hardwire kit includes low voltage protection. Do not bypass this feature, as it is crucial for preventing car battery drain.
- Keep the cables away from moving parts, heat sources, and sharp edges within the vehicle.
3. Package Contents
- 1 x AZDOME Hardwire Kit (3.5 meters cable)
- Various Fuse Taps (for different fuse box types)
- 1 x Pry Tool
- USB Connector Type (Mini USB, Micro USB, or Type-C, depending on selection)
4. Specifications
| Feature | Specification |
|---|---|
| Model Name | X22 |
| Item Type | Cables, Adapters & Sockets |
| Material | ABS |
| Item Weight | 0.1kg |
| Cable Length | 3.5 Meters |
| Input Voltage | DC 12V - 28V |
| Output Power | DC 5V / 2.5A |
| Low Voltage Protection (12V system) | Cut-off at 11.6V DC |
| Low Voltage Protection (24V system) | Cut-off at 23.6V DC |
| Interface Models | MINI USB, MICRO USB, TYPE-C |
| Special Features | Low Voltage Protection |
5. Setup & Installation
This section provides general installation steps. For a detailed visual guide, please refer to the official user manual PDF: User Manual (PDF).
Warning: If you have no experience in installing car electrical components, please seek professional assistance to avoid damage.
General Installation Steps:
- Locate the Fuse Box: Open your car's fuse box. The location may vary depending on your car model (e.g., under the dashboard, in the glove compartment, or under the hood).
- Identify Fuse Slots: Using a circuit tester, identify a fuse slot that is 'ACC+' (Accessory, powers on/off with ignition) and, if 24-hour parking monitoring is desired, a 'Bat+' (Battery, always powered) fuse slot.
- Install Fuse Holders: Insert the appropriate fuse taps into the identified fuse slots. Ensure the original fuse is placed in the lower slot of the fuse tap and a new fuse (matching the original's amperage) is placed in the upper slot for the hardwire kit.
- Connect Black Wire (Ground): Connect the black wire from the hardwire kit to a metal part of the car chassis. This serves as the negative electrode (ground).
- Route Cables: Carefully route the hardwire kit cables from the fuse box to your dash cam's mounting location, tucking them neatly along the car's trim to keep them out of sight and secure. Use the included pry tool to assist with tucking cables.
- Connect to Dash Cam: Plug the appropriate USB connector (Mini USB, Micro USB, or Type-C) into your dash cam.
- Test the System: Turn on your car's ignition and test the dash cam to ensure it powers on correctly. If wired for 24-hour parking monitoring, turn off the ignition and verify the dash cam remains powered and enters parking mode (if supported by your dash cam).
Wiring Configurations:
The hardwire kit has three wires: Red, Yellow, and Black. Their connection determines the power mode.
A. Standard ACC Wiring (No 24H Parking Monitoring)
This configuration powers the dash cam only when the car's ignition is on. It is suitable if you do not require continuous recording after the engine is off.
- Red Wire: Connect to an ACC (Accessory) fuse slot.
- Yellow Wire: Connect to an ACC (Accessory) fuse slot.
- Black Wire: Connect to a metal ground point on the car chassis.
B. 24H Parking Monitoring Wiring
This configuration provides continuous power to the dash cam, allowing it to monitor your vehicle even when the engine is off. The built-in low voltage protection will automatically cut off power if the car battery voltage drops below a safe level (11.6V for 12V systems, 23.6V for 24V systems).
- Red Wire: Connect to an ACC (Accessory) fuse slot.
- Yellow Wire: Connect to a BAT+ (Battery) fuse slot, which provides constant power even when the ignition is off.
- Black Wire: Connect to a metal ground point on the car chassis.
6. Operating Instructions
Once correctly installed, the AZDOME Hardwire Kit operates automatically:
- Ignition On: The dash cam will power on and begin recording according to its settings.
- Ignition Off (Standard ACC Wiring): The dash cam will power off.
- Ignition Off (24H Parking Monitoring Wiring): The dash cam will remain powered and, if supported by your dash cam, will enter parking monitoring mode. The hardwire kit's low voltage protection will continuously monitor your car battery's voltage and automatically cut off power to the dash cam if the voltage drops below the safe threshold (11.6V for 12V systems, 23.6V for 24V systems) to ensure your car can still start.
7. Maintenance
- Periodically check all wiring connections to ensure they remain secure.
- Inspect the fuse taps and fuses for any signs of damage or corrosion. Replace fuses if necessary.
- Ensure the hardwire cable is not pinched, cut, or exposed to extreme temperatures.
- Keep the dash cam and hardwire kit module clean and free from dust or debris.
8. Troubleshooting
- Dash Cam Not Powering On:
- Check all wire connections (Red, Yellow, Black) for proper installation.
- Verify that the fuse taps are correctly inserted into the fuse box and that the fuses are intact.
- Ensure your car battery has sufficient voltage.
- Parking Mode Not Working:
- Confirm that the yellow wire is connected to a 'Bat+' (constant power) fuse slot, not an 'ACC+' slot.
- Check your dash cam's settings to ensure parking mode is enabled and configured correctly.
- Verify that the car battery voltage is above the low voltage protection cut-off threshold.
- Dash Cam Powers Off Immediately After Engine Off:
- This indicates the kit is likely wired for Standard ACC mode. If 24H parking monitoring is desired, re-check that the yellow wire is connected to a 'Bat+' (constant power) fuse slot.
- Hardwire Kit Not Working on Specific Car Model (e.g., Nissan):
- Ensure you are using the correct type of fuse taps for your vehicle's fuse box.
- Verify the car's electrical system voltage (12V or 24V) is within the kit's supported range.
- Consult your car's manual for specific fuse box layouts and fuse types.
9. User Tips
- Patience with Installation: While feasible for DIY, installation can be a bit difficult. Take your time, follow the instructions carefully, and don't hesitate to seek professional help if unsure.
- Verify Parking Mode Settings: If parking mode isn't activating, always double-check your dash cam's internal settings in addition to the wiring. Some cameras require specific settings to enable parking surveillance.
10. Frequently Asked Questions (FAQ)
- Q: My parking mode is not working, what could be the reason?
- A: Ensure the yellow wire of the hardwire kit is connected to a constant power (Bat+) fuse slot in your car's fuse box. Also, verify that your dash cam's settings have parking mode enabled and configured correctly.
11. Warranty & Support
For any product-related inquiries, technical support, or warranty claims, please contact the seller or manufacturer directly. Keep your purchase receipt as proof of purchase.