XINOWY V8 / V8 SV

Contents

XINOWY V8 / V8 SV Bluetooth Motorcycle Helmet Headset Intercom User Manual

Product Overview

The XINOWY V8 and V8 SV are advanced Bluetooth helmet headset intercom systems designed for motorcycle riders and other multiplayer sports. They offer full-duplex communication for up to 5 riders, a maximum intercom distance of over 1000m, and various features including FM radio, noise reduction, NFC, GPS, and Bluetooth connectivity.

XINOWY V8/V8 SV Bluetooth Motorcycle Helmet Headset Intercom, showing two units and remote controls, highlighting 5 riders group talking.
XINOWY V8/V8 SV Intercom System for 5 Riders Group Talking

V8 vs V8 SV Models

The primary difference between the V8 and V8 SV models lies in the inclusion of a remote control. The V8 model comes with a remote control, while the V8 SV model does not. All other core functionalities remain consistent.

Comparison of V8 and V8 SV models, illustrating that V8 includes a remote control while V8 SV does not.
V8 vs V8 SV: Remote Control Inclusion

Package Contents

The following items are typically included in a 1 Set V8 SV package. Contents may vary slightly based on the specific model purchased.

  • Main Intercom Unit
  • Headset (earphones and microphone)
  • Foam Covers for earphones
  • Mounting Clamp and Screws
  • USB Charging Cable
  • User Manual (PDF available for download)
Contents of a 1 Set V8 SV package, including the main unit, headset, foam covers, mounting screws, charging cable, and user manual.
Typical Package Contents for 1 Set V8 SV

Component Identification

Main Unit (Host)

Diagram of the main unit (host) with labeled buttons and ports.
Main Unit Controls
  1. On Button
  2. Off Button
  3. Volume Down Button
  4. Volume Up Button
  5. Rider B Mode Button
  6. FM Radio / Rider A Mode Button
  7. Earphone and Charge Plug
  8. Deck (Mounting Point)

Remote Control (Optional - Included with V8 model)

Diagram of the remote control with labeled buttons.
Remote Control Buttons
  1. Music On/Off, Phone Button
  2. Rider A Mode Button
  3. Rider B Mode Button
  4. Volume Up Button
  5. Volume Down Button

Setup Instructions

Installation of Main Unit

Follow these steps to securely attach the intercom unit to your helmet:

Installation diagrams for the main unit, showing how to install the clamp on the helmet and buckle the V8.
Installation Diagram of Product Fastener and Clamp
  1. Install the clamp on the helmet using the provided screws.
  2. Buckle the V8 main unit onto the clamp in the direction indicated in the diagram.

Earphone and Microphone Installation

Connect the earphone and microphone to the main unit and position them inside your helmet:

Diagram showing the V8 installed on a crash helmet and a schematic of the earphone plug-in.
Earphone and Microphone Installation Schematic (Refer to the bottom right of the image for earphone installation)
  1. Install the earphone and microphone inside the helmet, ensuring the microphone is positioned close to your mouth.
  2. Plug the earphone and microphone jack into the designated port on the main unit.

Initial Power On

To turn on the host unit, hold the power button for approximately 2 seconds. The red light will illuminate, then release the button when the blue light flashes. The unit is now in 'on' mode.

Operating Instructions

Pairing with Mobile Phone/MP3/GPS Devices

To pair the host unit with your Bluetooth-enabled device:

  1. Ensure the host unit is off.
  2. Long press the power button for 3-5 seconds until red and blue lights flash alternately.
  3. On your mobile phone, MP3 player, or GPS device, enable Bluetooth and search for devices.
  4. Select "V8" from the list of available devices to initiate pairing.
  5. Upon successful pairing, the red light on the V8 unit will turn off, and the blue light will flash rhythmically.

NFC Pairing (for compatible phones): If your phone has NFC, enable the NFC function. Bring the host unit close to your phone, and it will automatically identify and pair. Once paired, it will automatically connect next time.

Phone Call Functions (via Host)

  • Answer a Call: When an incoming call lasts for about 6 seconds, the host will automatically answer it.
  • Decline a Call: When an incoming call rings for 5 seconds, short press the host's Power button to decline it.
  • End a Call: During a call, short press the host's Power button to end it.
  • Call Last Number: In standby mode, long press the Power button for about 2 seconds to automatically call the last telephone number in your call log.
  • Voice Control: Double-click the Power button to enter voice control mode. Double-click again to exit.

Music Control (via Host)

  • Music On/Off: In MP3 play mode, short press the Power button to pause or play the music.
  • Volume Control: During music playback, short press the "+" button to increase volume, and short press the "-" button to decrease volume.

FM Radio Function (via Host)

  • Enable Radio: After startup, connect the earphones. Press the A mode button for 3 seconds to enable the radio function.
  • Exit Radio: Short press the A mode button again to exit radio mode.
  • Frequency Modulation: In radio state, short press the "+" or "-" button to automatically search radio stations in high or low frequency bands.
  • Radio Volume Regulation: In radio state, long press the "+" button to gradually increase volume, and long press the "-" button to gradually decrease volume.

Remote Control Pairing (for V8 model)

Starting the Remote Controller: After correctly installing batteries and tightening the nut, the remote controller will automatically start.

Pairing between Remote Controller and Host:

  1. After both the remote controller and host are started, simultaneously press the volume "+" and "-" buttons on the host. The blue light will turn on normally after about 2 seconds.
  2. Operate the remote controller: First, short press the talking key to activate it. Then, press down any 2 buttons simultaneously for 3-5 seconds.
  3. When the blue lights on the remote controller flash, it indicates successful connection between the host and remote controller. (Effective remote-controlled distance: 10m)

Operations via Remote Control (for V8 model)

Once the remote controller and host are successfully paired, you can use the following functions:

  • Decline a Call: When an incoming call rings for 5 seconds, short press the Phone button on the remote controller to decline it.
  • End a Call: During a call, short press the Phone button on the remote controller to end it.
  • Call Last Number: Long press the Phone button on the remote controller to automatically call the last telephone number in the call log.
  • Music Control: Short press the Phone button on the remote controller to pause or play music.
  • Volume Control: During a phone call or music playback, short press the "+" button to increase volume, and short press the "-" button to decrease volume.
  • Next Song: Long press the "-" button on the remote controller to skip to the next song.
  • Previous Song: Long press the "+" button on the remote controller to skip to the previous song.
  • Radio Operations: Long press the A mode button for 3 seconds to enable radio function. Short press A button again to disable radio function.
  • Reconnection of Paired Devices: Long press the Phone button on the remote controller to automatically connect previously paired Bluetooth devices.

Intercom Pairing (Two V8 Units)

To pair two V8 units for intercom communication:

  1. Ensure both V8 units are in 'on' mode simultaneously.
  2. Long press the A button on both units for 5-7 seconds until red and blue lights flash alternately.
  3. Then, press the A button on either V8 unit. The red light on that device will turn off, and the blue lights will flash as it searches for a pairing state.
  4. After approximately 5-7 seconds, the red light on the other V8 unit will also turn off, and its blue lights will flash, indicating successful pairing.
  5. A short press on either A button will then allow you to enter intercom status.

Intercom Pairing (Five V8 Units)

Illustration showing five intercom units connected for real-time communication, emphasizing multi-brand compatibility for fleet travel.
Support for 5 Machines Real-time Intercom Function
Diagram illustrating the pairing process for five intercom units (A and B modes).
5-Phone Intercom Pairing Schematic
  1. Clear Pairing Records: Before pairing, in power-on state, long press A and B buttons simultaneously to clear any previous pairing records.
  2. Initial Connection: After pairing all 5 devices as shown in the diagram, double-click the first device and press A for the first connection. Wait for the machine to complete connections among all 5 devices.
  3. Exiting Intercom (Devices 2, 3, 4): If any of Device 2, 3, or 4 wishes to exit intercommunication, press the talking key once. To re-enter, press A once, then B.
  4. Exiting Intercom (Device 1): If Device 1 exits, press A once to return to intercommunication.
  5. Exiting Intercom (Device 5): If Device 5 exits, press B once to return to intercommunication.
  6. Mobile Phone Connectivity: Under 5-person intercommunication, only Device 1 and Device 5 can be connected with a mobile phone.

During intercommunication, a red LED flash indicates Conversion A, and a blue LED flash indicates Conversion B.

To Clear Five-Device Pairing Data: Press mode A and mode B buttons simultaneously for about 3 seconds. The red light will flash, indicating pairing data is cleared, allowing you to re-pair with any device.

Specifications

Feature Specification
Brand NameXINOWY
Model NameV8 / V8 SV
Item TypeHelmet Headset
Maximum Intercom Distance>1000m
Maximum Number of Speakers5
Connection ModeWire, Bluetooth
Power Supply ModeBuilt-in Battery
Battery IncludedYes
Support IntercomYes
Special FeaturesFM, Waterproof, Noise Reduction, NFC, GPS, Bluetooth
Applicable Helmet TypeHalf Helmet, MODULAR, Open face, Flip Up Helmet
Item Length15 cm
Item Width12 cm
Item Height3 cm
Item Weight48 g
External Testing CertificationCE
CertificationCE
Plug TypeUSB
OriginMainland China

Maintenance

To ensure the longevity and optimal performance of your XINOWY V8/V8 SV intercom, please follow these maintenance guidelines:

  • Cleaning: Wipe the unit with a soft, damp cloth. Do not use harsh chemicals or abrasive cleaners.
  • Storage: Store the unit in a dry place away from extreme temperatures and direct sunlight when not in use.
  • Charging: Use only the provided USB charging cable. Avoid overcharging the battery.
  • Water Exposure: While the unit is waterproof, avoid prolonged submersion in water. Ensure all ports are securely closed before exposure to moisture.

Troubleshooting

If you encounter issues with your intercom, try the following solutions:

  • Unit Not Powering On: Ensure the battery is charged. Press and hold the power button for the specified duration (2 seconds).
  • Pairing Failure: Make sure the unit is in pairing mode (red and blue lights flashing alternately). Clear previous pairing records if necessary (long press A and B buttons simultaneously for 3 seconds). Ensure your phone's Bluetooth is enabled and visible.
  • No Sound/Low Volume: Check that the earphones are properly plugged in. Adjust the volume using the "+" button on the unit or remote. Ensure the microphone is positioned correctly.
  • Intercom Disconnection: If intercom communication drops, try re-entering intercom mode by pressing the A button (for 2-unit pairing) or following the re-entry steps for 5-unit pairing.
  • Remote Control Not Responding: Check if the remote control batteries are correctly installed. Re-pair the remote control with the host unit if needed.

User Tips

  • Many users find the intercom works fantastically for group rides, providing clear communication.
  • The device is known to connect well with other intercom brands, such as Ejeas V6 Pro +, which can be beneficial for mixed groups.
  • For optimal sound quality, ensure the microphone is positioned correctly and the earphones are snug in your helmet.

Warranty and Support

This product comes with a 365 Days Free Replacement policy, ensuring peace of mind for your purchase.

For further assistance or detailed instructions, please refer to the comprehensive user manual available in PDF format:

View User Manual (PDF)

Applicable Use Cases

The XINOWY V8/V8 SV intercom system is versatile and suitable for various activities requiring real-time communication:

Visual representation of various applicable use cases for the intercom system, including bike riding, motorcycle riding, rock climbing, and teamwork games.
Versatile Use Cases: Bike Ride, Motorcycle Ride, Rock Climbing, Teamwork Games

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.