LAUNCH CRP123X Plus

Contents

LAUNCH CRP123X Plus OBD2 Scanner User Manual

Model: CRP123X Plus

1. Introduction

This diagnostic tool is designed to work with all OBD II compliant vehicles, including those with Controller Area Network (CAN). According to EPA regulations, all 1996 and newer vehicles (cars and light trucks) sold in the United States must be OBD II compliant. This includes American, Asian, and European vehicles.

Some 1994 and 1995 model year gasoline vehicles are also OBD II compliant. To verify compliance for these older models, check the Vehicle Emissions Control Information (VECI) Label, usually located under the hood or by the radiator. The label will explicitly state "OBD II Certified" if compliant.

LAUNCH CRP123X Plus OBD2 Scanner with main menu icons
Figure 1: LAUNCH CRP123X Plus OBD2 Scanner main interface showing Diagnose, OBD II, I/M, Reset, Battery Voltage, Data, Mall, Upgrade, and Settings icons.
LAUNCH CRP123X Plus OBD2 Scanner with accessories and quick start guide
Figure 2: LAUNCH CRP123X Plus OBD2 Scanner packaged with its quick start guide, carrying case, and diagnostic cables.

1.1 OBD II Definitions

Understanding the following terms is crucial for effective use of the OBD II system:

  • Malfunction Indicator Light (MIL): The vehicle's "Check Engine" warning light that activates when a Diagnostic Trouble Code (DTC) is stored.
  • Diagnostic Trouble Code (DTC): A code stored in the computer system's memory, identifying a fault condition.
  • Freeze Frame Data: Operating conditions stored when a DTC is set.
  • Parameter Identification Data (PID): Data returned by the vehicle's control modules to the diagnostic tool.
  • Monitors: Diagnostic routines programmed into the Powertrain Control Module (PCM) to test emission control systems.
  • Enabling Criteria: Vehicle-specific conditions that must occur before monitors run.
  • Drive Cycle: A specific mode of vehicle operation required to set readiness monitors.
  • Fuel Trim (FT): Feedback adjustments to the base fuel schedule (short-term for dynamic, long-term for gradual changes).
  • Data Link Connector (DLC): The 16-cavity connector on the vehicle for communication with diagnostic tools.
  • Powertrain Control Module (PCM): The vehicle's "on-board computer" controlling engine management, emissions, and powertrain operation.
  • Communication Protocols: Methods allowing vehicle systems to communicate, including CAN Bus, J1850 VPW, ISO 9141-2, J1850 PWM, and ISO 14230 KWP.

DTCs are five-digit alphanumeric identifiers. They can be:

  • Pending: Identified during a Drive Cycle but not yet meeting criteria to activate the MIL.
  • Stored: Occurred and met criteria to activate the MIL.
  • Permanent: Stored DTCs that can only be cleared by the OBD II system after repairs and a set number of Driving Cycles.

The first character of a DTC indicates the control system (P=Powertrain, B=Body, C=Chassis, U=Network). The subsequent characters provide specific malfunction details.

Front view of the LAUNCH CRP123X Plus OBD2 Scanner
Figure 3: Close-up front view of the LAUNCH CRP123X Plus OBD2 Scanner, highlighting the screen and navigation buttons.

2. Product Description

2.1 Components & Controls

Diagram of the LAUNCH CRP123X Plus OBD2 Scanner with numbered components
Figure 4: LAUNCH CRP123X Plus OBD2 Scanner with key components labeled.
  1. Charging LED: Red indicates charging, Green indicates fully charged.
  2. LCD: Displays test results and user interface.
  3. 5V charging port: Connects to external DC power for charging the tool.
  4. DB-15 diagnostic connector: Connects the tool to the vehicle's DLC.
  5. Power button: Turns the tool on/off.
  6. HOME button: Returns to the home (Job menu) screen.
  7. Selection buttons: Used for navigation (up, down, left, right) and selection.
  8. OK button: Confirms selections or actions.
  9. Return button: Exits the current program or returns to the previous screen.

2.2 Technical Specifications

FeatureSpecification
Screen5-inch 720P, touch screen
RAM2GB
ROM16GB
OBDII Input Voltage Range9~18V
ChargingDC 5V charging cable or Diagnostic cable via vehicle's DLC
Operating SystemAndroid 7.0
CPU1.5G
Battery6000mAh
Communication/UpgradeWIFI 2.4Ghz (b/g/n)
Dimensions232mm x 126mm x 34mm
WeightAbout 565g
Working Temperature0 to 50°C (32 to 122°F)
Storage Temperature-20 to 70°C (-4 to 158°F)
Software UpdateYes, Lifetime Free Update
CertificationsCE, FCC, RoHS

2.3 Accessories Checklist

The following items are typically included with your LAUNCH CRP123X Plus:

  • Diagnostic tool x 1
  • OBD II diagnostic cable x 1
  • DC 5V charging cable x 1
  • User manual x 1
  • Carrying bag x 1

3. Setup (Initial Use)

3.1 Charging the Device

There are two methods to charge your CRP123X Plus:

  • Via Charging Cable: Plug one end of the included DC 5V charging cable into the tool's DC-IN port and the other end into an external DC power source.
  • Via Diagnostic Cable: Insert one end of the diagnostic cable into the DB-15 connector of the tool and the other end into the vehicle's DLC.

The Charging LED will illuminate solid green when the battery is fully charged.

3.2 Getting Started (System Settings)

For first-time use, you need to configure some system settings:

  1. Press the [Power] button to turn on the device.
  2. The welcome page will appear. Tap "Start" to proceed.
  3. Choose your desired system language and tap "Next".
  4. Screenshot of the language selection screen on the device
    Figure 5: Language selection screen, showing options like English, French, Spanish, Deutsch, and Italiano.
  5. Choose the desired time zone and tap "Next" to enter the WLAN setup page.
  6. Slide the WLAN switch to ON. The system will search for available wireless networks.
    • If the chosen network is open, you can connect directly.
    • If the selected network is encrypted, enter the correct security key (password).
    Screenshot of the network settings screen on the device
    Figure 6: Network settings screen, displaying available Wi-Fi networks.
  7. After network connection, tap "Next Step" to configure your email address. Input your email and tap "Next Step". It is highly recommended to use a valid email address, as diagnostic reports will be automatically sent there.
  8. Carefully read the user agreement, check the box to agree to all terms, and tap "OK" to finish the sign-up process and navigate to the Job Menu.

4. Operating (Diagnose)

4.1 Connection to Vehicle

  1. Turn the vehicle's ignition OFF.
  2. Locate the vehicle's 16-pin Data Link Connector (DLC). This is typically found within 12 inches of the center of the instrument panel, under or around the driver's side. For some vehicles, the location may vary. Consult your vehicle's service manual if you cannot find it.
  3. Diagram showing common locations of the Data Link Connector (DLC) in a vehicle
    Figure 7: Common DLC locations (A-F) in various vehicle models, typically near the driver's side dashboard or console.
  4. Plug one end of the diagnostic cable into the vehicle's DLC port and the other end into the DB-15 diagnostic connector of the tool. Tighten the captive screws.
  5. Note: A plastic DLC cover may need to be removed on some vehicles. The cable connector is keyed and will only fit one way. Do not force it; rotate 180 degrees and try again if it doesn't connect easily.

  6. Turn the ignition ON. The engine can be off or running.
  7. Caution: Do not connect or disconnect any test equipment while the ignition is on or the engine is running.

  8. Press the [POWER] button on the tool to turn it on and enter the Job Menu.

4.2 System Diagnosing

This function is specifically designed to diagnose electronic control systems for single vehicle models. For CRP123X Plus/CRP129X Plus models, all vehicle systems with basic diagnostic functions are supported.

4.2.1 Smart Diagnosis (Auto-Detect)

This feature allows quick access to vehicle electronic control systems by decoding the VIN (Vehicle Identification Number), eliminating manual menu selection. Ensure "Automatic detection on connect" is set to ON in Settings, and a stable network connection is available for successful VIN access.

  • If the VIN is successfully obtained, the system will scan vehicle systems, generate a diagnostic report, and send it to your registered email.
  • If VIN information cannot be accessed, the tool will prompt for manual VIN input.

4.2.2 Manual Diagnosis

If VIN auto-detection fails, you can perform manual diagnosis by following on-screen instructions. Ensure the diagnostic program for your vehicle model is installed.

Flowchart for manual vehicle diagnosis
Figure 8: Manual Diagnosis Flowchart: Select "Diagnose" -> Vehicle Manufacturer -> Vehicle Model -> Scan Mode (Automatic System Detection or Manual System Selection) -> Test Function (Read Version Information, Read Fault Code, Clear Fault Code, Read Data Stream).

Key functions within manual diagnosis include:

  • Health Report (Fast Test): Quickly accesses all electronic control units and generates a detailed vehicle health report. Fault codes appear in red, normal systems in black.
  • Screenshot of the Health Report (Fast Test) screen showing system scanning results
    Figure 9: Health Report screen displaying scanning results for ECM, TCM, and ABS, with fault codes highlighted.
  • System Selection: Manually select the test system and function step-by-step.
  • Version Information: Reads system mode, vehicle VIN, software, and ECU version details.
  • Read Fault Code: Displays detailed DTC records. Do not clear codes if taking the vehicle to a service center, as this removes valuable diagnostic information.
  • Screenshot of the Diagnostic Trouble Code screen showing details for P0303 and P2097
    Figure 10: Diagnostic Trouble Code screen showing P0303 (Misfiring of Cylinder 3) and P2097 (Throttle Valve Block) with options for Help and Code Search.
  • Clear Fault Code: Erases DTCs from the vehicle. Ensure the ignition is ON and engine OFF. Clearing codes does not fix the underlying problem.
  • Read Data Stream: Retrieves and displays live data and parameters from the vehicle's ECU. Data can be viewed in text, waveform graphs, or combined graphs.
  • Screenshot of the Data Stream selection screen
    Figure 11: Data Stream selection screen, allowing users to select specific parameters like throttle positions for live monitoring.
    Screenshot of the Data Stream display screen showing live data parameters
    Figure 12: Data Stream display screen showing live data for Intake Air Temperature, Module Supply Voltage, and Electronic Pressure Control. Values outside the reference range are displayed in red.

4.3 OBDII Diagnosis

This option provides a quick way to check for DTCs, identify the cause of the MIL, check monitor status, verify repairs, and perform other emission-related services. After connecting to the vehicle's DLC and selecting "OBD II" from the Job Menu, the tool will automatically establish a communication link.

Functions available include:

  • Read Codes: Identifies the section of the emission control system with a malfunction.
  • Erase Codes: Clears codes from the vehicle after repairs.
  • I/M Readiness: Checks if emission-related systems are operating correctly and ready for inspection.
  • Data Stream: Retrieves and displays live data and parameters.
  • View Freeze Frame: Shows a snapshot of operating conditions when an emission-related fault occurred.
  • O2 Sensor Test: Retrieves O2 sensor monitor test results.
  • On-board Monitor Test: Retrieves test results for non-continuously monitored powertrain components.
  • EVAP System Test: Initiates a leak test for the vehicle's EVAP system.
  • Vehicle Info: Retrieves VIN, CID (Calibration ID), and CVN (Calibration Verification Number).

4.4 History

The tool records details of each diagnostic session. The History function allows direct access to previously tested vehicles and enables users to resume from the last operation without starting from scratch. All diagnostic records are listed in date sequence on the Manual Diagnosis main menu screen.

5. Maintenance

5.1 Reset (Service Function)

The CRP123X Plus offers various service functions for coding, resetting, and relearning, helping vehicles return to functional status after repair or replacement. Available tests vary by vehicle manufacturer, year, and model. Regular updates are recommended to access new service functions.

To perform a reset:

  1. Select "Reset" from the Job Menu.
  2. Choose the desired service function.
  3. Select the desired car brand.
  4. Select the reset mode (modes vary by vehicle).
  5. Follow the on-screen instructions to proceed.

5.2 Update

Keep your diagnostic software and APK synchronized with the latest versions for optimal performance and new features. A numeric indicator on the "Upgrade" module in the Job menu signifies available updates.

5.2.1 Update Diagnostic Software

  1. Tap "Upgrade" on the Job menu to enter the update center.
  2. By default, all diagnostic software is selected. Deselect any software by tapping "Unselect" and unchecking the box next to the vehicle model.
  3. Tap "Update" to begin downloading. This may take several minutes. You can pause, resume, or retry the download if network issues occur.
  4. Once downloaded, software packages will install automatically.

5.2.2 Renew Software Subscription

The CRP123X Plus includes two years of free diagnostic software use and updates. After this period, the software will be disabled. To unlock it, you must renew your subscription by purchasing a Subscription Renewal Card from the seller. A "Renew" button will appear on the screen when renewal is due. Follow the on-screen instructions to proceed. Ensure to double-check order information during subscription.

5.3 Clean Up

This option allows you to clear cache files and free up storage space on the device.

6. Troubleshooting

6.1 FAQ (Frequently Asked Questions)

The device includes a built-in FAQ section accessible via the "Data" menu, which provides answers to common questions regarding the tool's operation and functionality.

Screenshot of the Data menu screen with options like Diagnostic Report, DTC Library, etc.
Figure 13: Data menu screen, showing options for Diagnostic Report, Diagnostic Record, DTC Library, DLC Location, Feedback, Firmware Fix, and FAQ.

6.2 Feedback & Firmware Fix

  • Feedback: Use this feature to send details of diagnostic problems to LAUNCH for further analysis and troubleshooting.
  • Firmware Fix: This module allows you to upgrade and fix diagnostic firmware. Ensure power is not cut and no other interfaces are switched during this process.

7. User Tips

  • For optimal battery life, turn off WLAN when not in use.
  • Always ensure a stable internet connection for software updates and VIN auto-detection.
  • Regularly check for software updates to benefit from new functions and improved service.
  • When diagnosing, remember that clearing DTCs does not fix the underlying issue; it only clears the code. Address the root cause of the problem.
  • If you encounter issues, utilize the "Feedback" function to report problems directly to LAUNCH for support.

8. Warranty & Support

8.1 Warranty Information

LAUNCH electronic products are warranted against defects in materials and workmanship for one year (12 months) from the date of delivery to the user. This warranty is expressly limited to persons who purchase LAUNCH products for purposes of resale or use in the ordinary course of business.

The warranty does not cover parts that have been abused, altered, used for unintended purposes, or used inconsistently with instructions. The exclusive remedy for a defective automotive meter is repair or replacement. LAUNCH is not liable for consequential or incidental damages.

Final determination of defects will be made by LAUNCH. No agent, employee, or representative of LAUNCH has authority to bind LAUNCH to any affirmation, representation, or warranty concerning LAUNCH automotive meters beyond what is stated herein.

8.2 Customer Service

For questions regarding the operation of the unit, please contact your local dealer or LAUNCH TECH CO., LTD. directly:

LAUNCH reserves the right to make changes to this manual without notice. While efforts have been made to ensure accuracy, please contact customer service for any questions or clarifications.

For the full user manual in PDF format, please refer to: User Manual (PDF)

Documents and downloads

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.