1. Introduction
The AIFEN A11 is a compact and portable USB-powered soldering station designed for precision work, particularly in cell phone repair and other delicate electronic welding tasks. Its lightweight design, quick heating capabilities, and compatibility with various power sources make it an ideal tool for both professional and hobbyist use.

Figure 1: AIFEN A11 Soldering Iron highlighting its lightweight design (6.8g) and use of 210 soldering tips.
2. Package Contents
Please check the package for the following items:
- AIFEN A11 Soldering Iron Handle
- Soldering Tip (e.g., 210-K type, specific tip may vary by package)
- User Manual (this document, also available as PDF: Download PDF)

Figure 2: Contents of the AIFEN A11 package, showing the soldering iron, a 210-K tip, and the included instruction manual.
3. Setup
- Insert Soldering Tip: Carefully insert the desired 210 series soldering tip into the front end of the AIFEN A11 handle. Ensure it is seated firmly.
- Connect Power: The AIFEN A11 is powered via a USB Type-C interface. Connect a compatible USB-C cable to the soldering iron and to a power source.
- Compatible Power Sources: USB power adapters (wall chargers), power banks, or USB ports on stable power supplies that support QC3.0, PD, AFC, or FCP protocols.
- Recommended Power: For optimal performance and quick heating, use a power source capable of delivering 15V/60W or 20V/75W.

Figure 3: The AIFEN A11 can be conveniently powered by a power bank, enabling portable use.
4. Operating Instructions
The AIFEN A11 features a multifunction display and adjustment buttons for precise control.

Figure 4: Multifunction display frame with adjustment buttons for temperature, voltage, and calibration.
4.1. Power On/Off and Initial Heating
Once connected to a compatible power source, the soldering iron will power on automatically and begin heating to its last set temperature or default temperature. It heats up very quickly, typically reaching working temperature in about three seconds.
4.2. Temperature Adjustment
Use the adjustment buttons (left and right) located near the display.
- Increase Temperature: Press the right adjustment button once to increase the temperature by 1°C. Press and hold for at least one second for rapid temperature increase.
- Decrease Temperature: Press the left adjustment button once to decrease the temperature by 1°C. Press and hold for at least one second for rapid temperature decrease.
4.3. Switching Temperature Units (°C/°F)
Short press the adjustment button downwards (towards the tip) for 1 second to switch between Celsius (°C) and Fahrenheit (°F).
4.4. Voltage Option Function
Press the adjustment button for 3 seconds to enter the voltage option function. Adjust the setting parameters left and right (5V/9V/12V/15V/20V). Long press to save and exit.
4.5. Temperature Calibration (CAL Mode)
Press and hold the adjustment button downwards for 3 seconds to enter the temperature calibration interface (CAL mode).
- Adjust the setting parameters left and right (±99 degrees calibration).
- Press and hold the adjustment button downwards again to save and exit.
Alternatively, in the CAL interface, short press the adjustment button downwards to enter TEMP mode, which is another calibration mode using 350°C as the standard. Adjust parameters left/right, then long press to save and exit.
4.6. Gyroscope Function (Dormancy/Wake)
The AIFEN A11 features a gyroscope for intelligent power management.
- Dormancy: When the iron is still for a period, it enters dormancy mode to conserve energy and prevent tip oxidation.
- Wake: Simply pick up the soldering iron, and it will immediately switch status and resume working temperature.

Figure 5: The gyroscope function allows the iron to enter dormancy when still and instantly wake when picked up.
5. Maintenance
5.1. Soldering Tip Care
- Tinning: Always tin the tip with solder before and after use to prevent oxidation.
- Cleaning: Use a damp sponge or brass wool to clean the tip regularly during use.
- Storage: Store the iron with a tinned tip in a dry place.
- Replacement: Replace tips when they become excessively worn or corroded to maintain optimal performance.
5.2. General Cleaning
Wipe the body of the soldering iron with a soft, dry cloth. Do not use abrasive cleaners or solvents.
6. Troubleshooting
- Iron not heating:
- Ensure the USB-C cable is securely connected to both the iron and the power source.
- Verify that the power source is functioning correctly and provides sufficient power (voltage and wattage).
- Check if the soldering tip is properly inserted.
- Temperature display erratic:
- Ensure the tip is clean and properly seated.
- Perform a temperature calibration (see section 4.5).
- Iron enters dormancy too quickly/slowly:
- The gyroscope sensitivity is factory set. Ensure the iron is placed on a stable surface when not in use.
7. Specifications
| Feature | Specification |
|---|---|
| Model | A11 |
| Temperature Range | 100-450°C (212-842°F) |
| Voltage Range / Power Output | 5V/10W, 9V/27W, 12V/45W, 15V/60W, 18V/75W (18V with special bracket), 20V/75W |
| Interface Type | USB Type-C |
| Supported Protocols | QC3.0 / PD / AFC / FCP |
| Supported Soldering Tip Model | 210 Series |
| Weight | 6.8g (handle only) |
| Heat-up Time | Approx. 3 seconds |
| Recovery Time | Approx. 1 second |

Figure 6: Supported charging protocols and voltage/wattage ranges for the AIFEN A11.
Note: An optional bracket (sold separately) can provide stable support and may be required for certain power outputs (e.g., 18V/75W).

Figure 7: The AIFEN A11 can be used with an optional bracket (sold separately) for enhanced stability and higher power output.
8. User Tips
- Portability: Leverage its USB-C power input by using a high-capacity power bank for soldering on the go, making it extremely convenient for field repairs.
- Quick Heat-up: The rapid heat-up time (around 3 seconds) means you can start working almost immediately, saving time on projects.
- Precision Work: Its compact size and fine tips make it excellent for delicate tasks like FPC soldering and working with low-melt solders (e.g., 138°C solder) in mobile device repair.
- Power Source Quality: For best performance, especially for quick heating and recovery, use a high-quality USB-C power adapter or power bank that supports the higher wattage outputs (e.g., 15V/60W or 20V/75W).
9. Warranty and Support
For warranty information and technical support, please refer to the seller's policies or contact the point of purchase. Keep your proof of purchase for any warranty claims.