KPSUN LED Underground Light

Contents

KPSUN LED Underground Light User Manual

Model: LED Underground Light

Introduction

Thank you for choosing the KPSUN LED Underground Light. This product is designed for outdoor decorative and landscape lighting, offering durability and energy efficiency. This manual provides essential information for the safe installation, operation, and maintenance of your LED underground light. Please read these instructions carefully before installation and retain them for future reference.

Safety Information

  • This is a 12V/24V lamp. Use only with a constant voltage power supply.
  • Do not reverse the power supply input and output connections. Ensure correct polarity (Red for +, Black for -).
  • Installation should be performed by a qualified electrician or in accordance with local electrical codes.
  • Ensure the power is disconnected before installation, maintenance, or cleaning.
  • Do not attempt to modify or disassemble the light fixture, as this will void the warranty and may cause damage or injury.
  • Ensure the light is installed in a location where it will not be subjected to excessive mechanical stress or damage.

Package Contents

  • LED Underground Light Fixture
  • Mounting Sleeve (Black plastic)
  • Stainless Steel Spring Clips (pre-attached or separate)
LED underground light with its separate mounting sleeve and connected wiring.
LED underground light with mounting sleeve and wiring.

Specifications

Feature Detail
Product NameDC Low Voltage Buried Light
Input VoltageDC12V / DC24V
Power2W (also available in 3W variants)
Light Body MaterialStainless Steel
Emitting ColorsCold White, Nature White, Warm White, Blue, Red, Green
Protection ClassIP67 (Waterproof)
Luminous Flux100-130 Lm/W
Beam Angle45°
Lifetime30,000 hours
CertificationsCE, RoHS
Dimensions (approx.)D42mm or D52mm (diameter), H37mm (height)
ApplicationGardens, Streets, Squares, Villas, Parks, Lawns, Terraces, Fountains, Waterfalls, Decks, Paths, Roads, Steps, Porches, Driveways, Bed Rooms
Dimensional diagram showing D42mm and D52mm light variants, their height (H37mm), and corresponding mounting sleeve dimensions.
Product Dimensions for D42mm and D52mm variants.

Setup and Installation

Before beginning installation, ensure all power to the installation area is turned off at the circuit breaker.

Wiring Instructions:

The LED underground lights operate on DC12V or DC24V safety voltage. Connect the lights to a compatible constant voltage power supply (AC85-265V input, DC12V/24V output).

  • For single-color lights: Connect the Red wire to the positive (+) terminal and the Black wire to the negative (-) terminal of your DC power supply.
  • For RGB/RGBW lights: Connect the Red, Green, Blue, and White wires to their respective color channels, and the common positive (+) wire to the positive terminal of your DC power supply.
Wiring diagram for DC12V/24V safety voltage lights, showing connections for single color (red/black) and RGB/RGBW (R, G, B, W, +) configurations.
Wiring Diagram for DC12V/24V lights.

Installation Steps:

  1. Provide Mounting Holes: Prepare mounting holes that precisely match the product dimensions (D42mm or D52mm, refer to the dimensions diagram). Ensure adequate depth for the light fixture and its mounting sleeve.
  2. Insert Mounting Sleeve: If using a separate mounting sleeve, insert it into the prepared hole.
  3. Press Stainless Steel Spring into Hole: Gently press the stainless steel spring clips on the light fixture inwards so they can fit into the mounting hole or sleeve.
  4. Push Light Fitting Inwards: Carefully push the light fitting into the prepared hole until it sits flush with the surface. The spring clips will secure it in place.
Installation steps diagram: 1. Provide mounting holes, 2. Press stainless steel spring into hole, 3. Push light fitting inwards.
Visual guide for installation steps.
Product demonstration video showing the light from various angles and its illumination, which may provide additional installation context.

Operating Instructions

Once properly installed and wired to a compatible DC12V or DC24V power supply, the LED underground light will illuminate when power is supplied to the circuit. To turn the light on or off, use the switch connected to your power supply circuit.

For RGB/RGBW variants, a compatible controller (not included) is required to change colors and modes.

Maintenance

  • Cleaning: Periodically clean the surface of the light with a soft, damp cloth to remove dirt and debris. Do not use abrasive cleaners or solvents.
  • Inspection: Regularly inspect the wiring and connections for any signs of wear, damage, or corrosion. Ensure the light remains securely seated in its mounting.
  • Water Drainage: Ensure that the installation area has proper drainage to prevent water from pooling around the light fixture, despite its IP67 rating.

Troubleshooting

  • Light does not turn on:
    • Check if the power supply is connected and receiving power.
    • Verify all wiring connections are secure and correct (positive to positive, negative to negative).
    • Ensure the power supply output voltage matches the light's requirement (DC12V or DC24V).
    • Test the light with a known working power source if possible.
  • Light flickers or is dim:
    • Check for loose wiring connections.
    • Ensure the power supply is providing stable voltage and sufficient current for all connected lights.
    • Verify the power supply is a constant voltage type.

User Tips

No specific user tips were available from reviews or Q&A at the time of manual creation. However, general tips for outdoor lighting include:

  • Plan your lighting layout carefully to achieve desired aesthetic and functional effects.
  • Consider using a timer or smart controller for automated operation.
  • For optimal longevity, ensure proper sealing of all connections, especially in wet environments.

Warranty and Support

This KPSUN LED Underground Light comes with a Two-year free replacement warranty from the date of purchase, covering manufacturing defects. Please retain your proof of purchase for warranty claims.

For more detailed information, including comprehensive diagrams and safety guidelines, please refer to the official user manual PDF available at: User Manual (PDF).

For technical support or warranty inquiries, please contact your retailer or the manufacturer directly.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.