1. Introduction
The Aigo AM12PRO RGB FAN is a high-performance 120mm PC case fan designed to provide efficient cooling and vibrant ARGB lighting for your computer system. This manual provides essential information for the safe and correct installation, operation, and maintenance of your AM12PRO fan.
2. Safety Information
Please read and understand the following safety precautions before installing or using the product:
- Ensure your computer is powered off and unplugged from the wall outlet before installation.
- Avoid touching the fan blades while the fan is operating.
- Do not expose the fan to moisture or extreme temperatures.
- Handle components with care to prevent damage.
- If you are unsure about any installation steps, consult a qualified technician.
3. Package Contents
The Aigo AM12PRO RGB FAN package typically includes:
- Aigo AM12PRO 120mm Fan(s)
- Mounting Screws
- (Optional, depending on variant) ARGB Controller
- (Optional, depending on variant) ARGB Light Bar
Note: The exact contents may vary based on the specific product variant (e.g., single fan, 3-pack, with controller). Please check your product packaging.
4. Specifications
| Feature | Specification |
|---|---|
| Model Number | AM12PRO |
| Fan Size | 120mm |
| Voltage | 12V |
| Fan Speed | 800 - 1600 RPM |
| Noise Level | 28 dBA |
| Air Volume | 81.6 CFM |
| Power Consumption | 3.5W |
| Bearing Type | Fluid Bearing |
| Fan Life Expectancy | 100,000 hours |
| Power Interface | 4-PIN (PWM), SATA, 5V 3-PIN (ARGB) |
| Used For | Case, Radiator |
5. Setup and Installation
Follow these steps to install your Aigo AM12PRO RGB FAN:
- Prepare Your System: Power off your computer and unplug it from the power outlet. Open your PC case to access the fan mounting locations.
-
Mount the Fan: Position the fan in your desired location (e.g., front, rear, top, bottom of the case, or on a radiator). Use the provided mounting screws to secure the fan. Ensure the fan is oriented correctly for optimal airflow (intake or exhaust).
The AM12PRO fans are equipped with anti-vibration mats on the corners to reduce noise. Ensure these are properly seated during installation.
Image: Fan with anti-vibration mat detail.
Image: Fan illustrating airflow direction (arrows indicate air movement).
- Connect Power (PWM): The fan has a 4-PIN PWM connector. Connect this to an available 4-PIN fan header on your motherboard. This allows for speed control based on system temperature.
-
Connect ARGB Lighting (5V 3-PIN): The fan features 5V 3-PIN ARGB lighting. Connect this cable to a compatible 5V 3-PIN ARGB header on your motherboard or to an ARGB controller. Do NOT connect to a 12V RGB header, as this will damage the LEDs.
Image: Fan showing 4-PIN PWM and 5V 3PIN connectors.
-
Daisy-Chaining (Optional): If you have multiple AM12PRO fans or other ARGB products, you can daisy-chain their 5V 3-PIN ARGB connectors to a single motherboard header or controller. Ensure your motherboard/controller can support the total number of LEDs.
Wiring Diagrams:
Three in One Connection: Connect Fan 1, Fan 2, and Fan 3's 5V 3-Pin ARGB cables in series. The last fan in the series connects to the 5V 3-Pin ARGB port on your motherboard or controller. Each fan's 4-Pin PWM cable connects to a PWM port, or they can be connected to a fan hub which then connects to a single PWM port on the motherboard.
Five in One Connection: Similar to the three-in-one, connect Fan 1 through Fan 5's 5V 3-Pin ARGB cables in series. The final ARGB connection goes to the motherboard or controller. Each fan's 4-Pin PWM cable connects to a PWM port, or a fan hub can be used for consolidated PWM control.
For detailed wiring diagrams, please refer to the official PDF manual linked in the 'Warranty and Support' section.
- Cable Management: Route cables neatly to avoid interference with other components and to improve airflow.
- Close Case and Power On: Close your PC case, plug in the power cable, and power on your computer. Verify that the fans are spinning and the ARGB lighting is functioning.
6. Operating Instructions
Once installed, your Aigo AM12PRO fan will operate automatically.
- Fan Speed Control (PWM): The 4-PIN PWM connection allows your motherboard to dynamically adjust fan speed based on CPU or system temperatures. You can typically configure fan curves in your motherboard's BIOS/UEFI settings or through manufacturer-provided software.
- ARGB Lighting Control: The 5V 3-PIN ARGB connection allows you to synchronize and customize the fan's lighting effects. This is usually done via your motherboard's RGB software (e.g., ASUS Aura Sync, MSI Mystic Light Sync, Gigabyte RGB Fusion, ASRock Polychrome Sync) or a dedicated ARGB controller if you are using one.
7. Maintenance
Regular maintenance helps ensure optimal performance and longevity of your fan:
- Cleaning: Periodically clean the fan blades and housing to remove dust buildup. Use compressed air or a soft brush. Ensure the fan is powered off and unplugged before cleaning.
- Inspection: Check for any loose cables or obstructions that might hinder fan operation or airflow.
8. Troubleshooting
-
Fan Not Spinning:
- Ensure the 4-PIN PWM connector is securely plugged into a motherboard fan header.
- Check your motherboard's BIOS/UEFI settings to ensure the fan header is enabled and configured correctly.
- Verify that your power supply is providing adequate power.
-
RGB Lighting Not Working:
- Ensure the 5V 3-PIN ARGB connector is securely plugged into a compatible 5V 3-PIN ARGB header on your motherboard or controller.
- Double-check that it is NOT connected to a 12V RGB header.
- Check your motherboard's RGB software or controller settings to ensure lighting is enabled and configured.
- If daisy-chaining, ensure all connections are firm.
-
Fan is Loud/Vibrating:
- Ensure all mounting screws are tightened.
- Check that the anti-vibration mats are properly installed.
- Clean any dust buildup on the fan blades.
- Verify that no cables are touching the fan blades.
-
Fan Speed Not Changing:
- Confirm the 4-PIN PWM connector is used (not a 3-PIN connector).
- Check your motherboard's BIOS/UEFI fan control settings or software.
9. User Tips
- Optimize Airflow: Pay attention to the fan's airflow direction (indicated by arrows on the fan frame) to create an effective cooling path within your PC case. Generally, front and bottom fans are intake, while rear and top fans are exhaust.
- Fan Speed vs. Noise: Experiment with fan speed settings in your motherboard's BIOS or software to find a balance between cooling performance and noise levels that suits your preference.
- Cable Management: Proper cable management not only makes your build look cleaner but also improves airflow, contributing to better cooling performance.
10. Warranty and Support
Aigo products are designed for reliability and performance. For warranty information and technical support, please refer to the official Aigo website or contact your retailer.
A detailed user manual, including comprehensive wiring diagrams, is available in PDF format. You can access it here: Aigo AM12PRO User Manual (PDF)
Product Showcase Video
Video: Aigo AM12PRO RGB FAN product showcase, demonstrating lighting effects and installation in a PC build.