GANGLE F2GT-1A180-DD

Contents

GANGLE TPMS Sensor Instruction Manual

Model: F2GT-1A180-DD

Introduction

This manual provides essential information for the proper installation, operation, and maintenance of your GANGLE Tire Pressure Monitoring System (TPMS) Sensor. Please read all instructions carefully before proceeding to ensure correct functionality and safety.

Important Safety Warnings

Read all instructions and warnings, and review all illustrations before installing. Professional installation is highly recommended.

  • These TPMS sensor assemblies are replacement or maintenance parts for motor vehicles that have a factory-installed TPMS only.
  • Failure to follow installation instructions may result in the failure of the motor vehicle TPMS sensor to operate properly.
  • Each TPMS sensor is designed to operate with specific vehicle makes, models, and years using proper frequencies. Only install TPMS sensors designated for your specific vehicle.
  • Improper TPMS installation or the use of unauthorized TPMS sensors can cause the vehicle's TPMS system to fail.
  • Do not install TPMS sensors in damaged wheels.
  • Upon completion of installation, test the motor vehicle TPMS system using procedures described in the original manufacturer's service guide to confirm proper installation.
  • If the TPMS system continues to fail, consult technical support or an authorized motor vehicle dealership.
  • These TPMS sensor assemblies are designed to operate in Original Equipment wheels and tires only. If non-Original Equipment wheels and/or tires are used, the TPMS system may not function correctly.
  • The vehicle owner assumes sole responsibility for TPMS and vehicle function if non-Original Equipment wheels and tires are used.
  • WARNING: FAILURE TO FOLLOW INSTALLATION INSTRUCTIONS OR THE USE OF IMPROPER TPMS SENSORS MAY RESULT IN THE MOTOR VEHICLE TPMS SYSTEM FAILURE CAUSING PROPERTY DAMAGE, PERSONAL INJURY OR DEATH.

Product Overview: Understanding TPMS

The Tire Pressure Monitoring System (TPMS) continuously monitors your vehicle's tire pressure to ensure safety and optimal performance.

Benefits of TPMS

  • Safety: Notifies you if tire pressure falls 25% below recommended inflation, helping prevent blowouts and flat tires.
  • Cost Savings: Properly inflated tires reduce tire wear and save fuel. Underinflated tires can significantly reduce fuel efficiency.
  • Performance: Correct tire pressure optimizes traction, handling, steering, stability, and braking.
  • Environmental Impact: Properly inflated tires contribute to reduced CO2 emissions.

How Direct TPMS Works

TPMS sensors are installed in each wheel and transmit pressure information to a receiver in your vehicle. When low tire pressure or a malfunction is detected, the TPMS indicator light appears on your dashboard.

Diagram showing how direct TPMS sensors are installed in wheels and transmit data to the vehicle's receiver.

Image: Diagram illustrating the installation and function of direct TPMS sensors within a vehicle's wheel.

TPMS Light Indicators

  • Solid Light: Indicates one or more tires have low air pressure (20% below recommended placard pressure). Solution: Add air to meet placard recommendation.
  • Flashing Light: Indicates a dead sensor battery, a missing sensor, a broken sensor, or an incorrect sensor for the vehicle type. Solution: Replace sensor, relearn sensor.

Specifications

Feature Detail
Manufacture Part Number F2GT-1A180-DD
Replacement Part Numbers F2GT-1A180-CC, F2GT-1A180-DB, F2GT-1A180-DC, F2GT-1A180-CD, F2GT-1A180-DD, F2GT-1A150-CB
Operating Frequency 433MHz
Fitment Type Direct Replacement
Material Designed for Ford Mondeo, Focus, Ecosport, Transit, Tourneo Custom, Galaxy, Explorer, Mustang, Ranger, Fiesta, S-Max

Vehicle Fitment (EU Market)

  • Ford Ecosport: 11/2017-12/2020
  • Ford Edge: 06/2014-12/2020
  • Ford Escape: 01/2014-12/2020
  • Ford Explorer: 09/2015-08/2019
  • Ford Fiesta: 01/2017-12/2020
  • Ford Focus: 05/2018-12/2009
  • Ford Focus IV: 09/2018-05/2019
  • Ford Focus ST: 03/2018-12/2020
  • Ford Galaxy: 05/2015-12/2020
  • Ford Mondeo: 09/2017-12/2020
  • Ford Mustang: 01/2015-12/2020
  • Ford PUMA: 11/2019-12/2020
  • Ford Ranger: 01/2016-12/2020
  • Ford SMAX: 05/2015-12/2020
  • Ford Tourneo Connect: 05/2018-12/2020
  • Ford Tourneo Custom: 01/2020-12/2020
  • Ford Transit: 01/2020-12/2020
  • Ford Transit Combi: 01/2019-12/2020
  • Ford Transit Connect: 05/2018-12/2020
  • Ford Transit Custom: 01/2020-12/2020
  • Ford Vignale S-Max: 01/2015-12/2020

Vehicle Fitment (US Market)

  • Ford Explorer: 2015/06-2019/12
  • Ford F-150: 2015/01-2018/12
  • Ford F Series SD: 2015/01-2018/12
  • Ford Fusion: 2017/01-2019/12
  • Ford Mustang: 2015/01-2018/12
  • Ford Taurus: 2015/11-2019/12
  • Ford Continental: 2017/01-2020/12
  • Lincoln MKX: 2015/07-2019/12
  • Lincoln MKZ: 2015/09-2019/12

Please ensure your existing part number matches one of the numbers listed above. If the numbers do not match, the part may not work with your vehicle.

Installation Process

Installation of TPMS sensors should ideally be performed by trained professionals. The following steps outline the general procedure for removal and installation.

Visual Reference: TPMS Sensor Details

Close-up of TPMS sensor side with markings.

Image: Side view of the TPMS sensor, highlighting product markings.

Close-up of TPMS sensor back with model number F2GT-1A180-DD.

Image: Rear view of the TPMS sensor, showing the model number F2GT-1A180-DD.

Close-up of TPMS sensor front with valve stem.

Image: Front view of the TPMS sensor, including the valve stem.

Step-by-Step Installation

  1. Loosen the Tire: Remove the valve cap and core, then deflate the tire.
  2. Dismount the Tire: Clamp the tire onto the tire changer. Adjust the valve at 1 o'clock relative to the tire separation head. Insert the tire tool and lift the tire bead onto the mounting head to dismount the head.
  3. Dismount the Sensor: With a screwdriver, remove the fastening screw and sensor from the valve stem. Then loosen the nut and remove the valve.
  4. Mount Sensor and Valve: Slide the valve stem through the valve hole of the rim. Tighten the screw-nut with 4.0 Nm using a positioning pin. Assemble the sensor body against the rim and tighten the screw. Ensure the sensor body and valve stem are firmly connected.
  5. Mount the Tire: Place the tire on the rim, ensuring the valve faces the separation head at an angle of 180 degrees. Mount the tire over the rim.

CAUTION: Do not re-use the removed valve core. Always replace with a new electroless nickel-plated valve core (aluminum stem). Use of non-electroless nickel-plated cores with aluminum valve stems can result in galvanic corrosion and loss of tire pressure. Tighten core with an approved valve core tool to 0.23Nm - 0.56Nm (2 in-lbs. - 5 in-lbs.). Do Not Over tighten!

Relearn Procedure

Your TPMS sensors come pre-programmed for your vehicle's make, model, and year. However, they need to be activated or

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.