Skydroid T10

Contents

Skydroid T10 Remote Control System User Manual

Model: T10

Quanzhou Skydroid Technology Co., Ltd.

Important Safety Information

WARNING:

  • Misuse of this product may result in injury, damage, or loss of property. Read this manual carefully before using.
  • This item is not a toy. It is intended for use by professional UAV operators and installers only.
  • Do not use this product if you lack the knowledge and expertise to install and maintain UAV radio equipment.
  • DO NOT use unapproved or unofficial components with this system.
  • Operators must strictly follow the operation guides set forth in this manual.
  • Skydroid does not accept any liability for the use or misuse of this product.
  • DO NOT fly under the influence of substances, or when tired.
  • DO NOT fly in strong wind and/or rainy conditions.
  • DO NOT fly close to electric emission towers, communication stations, and crowded areas.
  • DO NOT fly nearby airports and other prohibited areas.
  • DO NOT fly around people or animals, or in any location where possible to damage property.
  • Check equipment before every flight and carry out maintenance and repairs as needed.
  • Use certified chargers to charge the batteries.
  • DO NOT put unnecessary force on antennas or electronic components to avoid damage.
  • DO NOT put the T10 into water. If it does, switch off the power and dry it.
  • DO NOT crash the T10 or break the battery.

Product Overview

The Skydroid T10 is a versatile remote control system designed for various unmanned aerial vehicles (UAVs) and remote-controlled models. It features advanced communication technologies for reliable control, digital video transmission, and data telemetry.

Skydroid T10 Remote Control with a tablet displaying a map interface, alongside a mini camera, receiver, and cables.
Skydroid T10 Remote Control with a tablet displaying a map interface, alongside a mini camera, receiver, and cables.

Key Features:

  • Dual antenna plus dual RF module with integrated control algorithms for reliable communication via full angle high gain antennas.
  • Utilizes FHSS (Frequency Hopping Spread Spectrum) technology for precise control.
  • Integrated digital video transmission with a range of up to 10KM.
  • Integrated data transmission with a range of up to 20KM.
  • Parameter adjustments via APP with upgraded traditional OSD to touch panel control.
  • Connectivity via Bluetooth or USB, supporting S.BUS, PPM, PWM, Serial ports, and external devices.
  • APP connectivity via Bluetooth for operation model switching, data adjustment (forward/reverse, rudder volume, channel binding, runaway protection value, SBUS, PPM output, digital baud rate), and parameter saving/loading.
  • Based on the "Tower" APP for optimal compatibility with Pixhawk systems, offering a large map view for waypoint selection and route planning, including one-key return to home. Supports Tower, QGC, JIYI, TOPXGUN, and BOYING APP.
  • Powered by two 18650 batteries (sold separately), providing over 20 hours of endurance with 20dBm transmission frequency.
  • Highly integrated datalink with video & data transmission and telemetry in an all-in-one unit.
  • Ultra-small size with folding brackets for strong and stable mounting.
  • Optional cameras available, including mini digital camera, digital camera with LED, and 20x zoom camera.

Main Application:

The Skydroid T10 is specifically designed for UAVs, Helicopters, Fixed Wing aircraft, Multi-Rotors, or Boat operations. It facilitates video transmission (with optional camera), data link, and control of the UAV.

Specifications

Controller Data (T10)

Parameter Value Parameter Value
Model T10 Channels 10
Working Voltage 4.2V Working Current 100mA
Frequency 2.400-2.483GHz Modulation New FHSS
Firmware APP online Weight 525g
Dimension 160*150*50mm Battery Capacity 4000mA
Duration 20 (Hours) Charge Port MICRO-USB
Application Helicopter, Fixed wing, Quadcopter, Car, Boat

Receiver Data (R10)

Parameter Value Parameter Value
Model R10 Channels 10
Working Voltage 4.5-5.5V Working Current 100mA
Dimension 50*31*12(mm) Weight 20g

Mini Camera Specifications (MINIDCAM)

Parameter Value Parameter Value
Model MINIDCAM Size 30*29*26mm
Working Current 180mA Weight 15.6g

Package Contents

Item Quantity Remarks
T10 Main unit 1 piece
R12 Receiver 1 piece
MINIDCAM 1 piece
Micro USB OTG cable 1 piece For video transmission
Type C USB OTG cable 1 piece For video transmission
Hexagon key 1 piece For phone mount adjustment
Tools 1 piece Change mode
Hanging strap 2 piece
Stick cap 2 piece
Contents of the Skydroid T10 package, including the remote control, receiver, cables, and accessories.
Contents of the Skydroid T10 package, including the remote control, receiver, cables, and accessories.

Setup

1. Pre-Check and Preparation

  1. Check T10 battery level.
  2. Check position of the antenna to get better performance.
  3. Make sure the firmware is the latest version.
  4. DO NOT operate under the influence of alcohol or drugs.

2. Controller Parts and Antenna Placement

Ensure the T10 controller antennas are upright for optimal performance. Avoid placing antennas parallel to the controller or inside the drone's body.

Skydroid T10 Remote Control with its tablet holder extended, showing the front panel and joysticks.
Skydroid T10 Remote Control with its tablet holder extended, showing the front panel and joysticks.
Angled view of the Skydroid T10 Remote Control with antennas extended and tablet holder.
Angled view of the Skydroid T10 Remote Control with antennas extended and tablet holder.

Correct Antenna Position for UAV:

  • Place antennas far from the central board.
  • Keep antennas upright without any obstacles.
  • Alternatively, mount antennas under the drone arm.

Incorrect Antenna Placement:

  • DO NOT put antennas inside the board.
  • DO NOT place antennas close to Carbon Fiber or Metal parts.
  • DO NOT cross the antenna between the central Flight control board and container.

3. Connecting with Device Helper App (Android Only)

  1. Ensure the receiver and flight controller are ready and powered on.
  2. Download the "Device Helper" APP from www.skydroid.xin.
  3. Turn on the T10 (short press + long press the power button).
  4. Enable Bluetooth on your Android phone and search for "T10-XXX".
  5. Select and enter the pairing code "1234" to connect.
  6. Once connected, enter the controller interface in the APP to adjust parameters.

Parameter Adjustment Example:

  • Channel 1 (X2): No Reverse, Failsafe value 1500, min travel 1000, max 2000.
  • Channel 2 (Y2): No Reverse, Failsafe value 1500, min travel 1000, max 2000.
  • Channel 3 (Y1): No Reverse, Failsafe value 900, min travel 1000, max 2000.
  • Channel 4 (X1): No Reverse, Failsafe value 1500, min travel 1000, max 2000.

Attention for Parameter Adjustment:

  • Select values between 900-2100. For Failsafe, select "0" for hold.
  • Click "SAVE" at the top right corner to record changes.
  • Adjusted parameters are saved in the APP. Click "write" to load data to the controller. A "Di" sound indicates successful communication.

4. Receiver and Flight Controller Connection

  1. **Binding**: Press and hold the pairing button on the receiver for 2 seconds until the green light flashes. Turn on the T10 main unit to complete pairing. A solid green light indicates successful pairing.
  2. **Data Link**: Use the provided wire or a DIY connector to connect the receiver's Tx pin to the flight control board's Rx pin.

5. T10 Connection to Android Phone for FPV

  1. Connect the receiver to the camera (e.g., mini digital camera) and power up the system.
  2. Download the "Skydroid FPV" APP from www.skydroid.xin.
  3. Connect the T10 to your phone via Bluetooth (refer to step 3 above).
  4. Click "Yes" to confirm, and the image from the camera will display on your phone.
  5. For detailed usage of Skydroid FPV, visit the official website.

6. T10 Connection to PC for Mission Planner/QGC

  1. Use two USB connector cables to link between USB1 on the T10 and a USB port on your PC. Select the correct port for the ground station. Set the Baud Rate to 115200 to link with the flight controller's data port. (Note: QGC/Mission Planner need Skydroid SDK for image display, currently under development).
  2. Use a Micro data cable to connect USB2 on the T10 to your PC. Set the Baud Rate to 57600 (supports data only, not video).

Operating Instructions

Power On/Off

  • To power on: Short press, then long press the power switch.
  • To power off: Short press, then long press the power switch.

Charging the T10

The T10 main unit uses two 18650 batteries (sold separately). Charge using the standard Micro USB port with a 5V power adapter (e.g., mobile phone charger).

Two 18650 batteries, 3.7V 2000mAh, used for the Skydroid T10.
Two 18650 batteries, 3.7V 2000mAh, used for the Skydroid T10.
  • LED status during charging: LED flashes.
  • LED status when fully charged: LED turns off.
  • If you observe smoke, heat, or an unusual smell during charging, immediately stop charging and return the controller for servicing.
  • Do not leave the product unattended while charging.
  • Do not leave the product in a place where children can reach.
  • DO NOT charge when room temperature is over 60°C.

Battery Level Indication

LED Indication Battery Level
4 LEDs ON 75%-100%
3 LEDs ON 50%-75%
2 LEDs ON 25%-50%
1 LED ON 0%-25%

Changing Operating Mode

To change the operating mode (e.g., Mode 1 or Mode 2), link your system with the radio via Bluetooth. Then, open the Device Helper APP, select the desired mode, and save. No further settings are required.

Gimbal Calibration

For gimbal calibration, please refer to the video instructions available on www.skydroid.xin.

Maintenance

Environmental Conditions for Operation:

  • Operating Temperature: -10°C to +55°C
  • Relative Humidity: Do not exceed 85%.
  • Atmospheric Pressure: 86kPa to 106kPa.
  • The working environment should not contain explosive material or any corrosive or harmful gas that may interfere with product operation.
  • Always work under shelter to prevent rain, snow, wind, sand, and dust contamination.

Storage

  • Store the T10 in a dry and ventilated area.
  • Avoid direct sunlight to prevent harm to the internal LiPo battery.
  • If storing for over three months, it is highly recommended to keep it at room temperature between 22°C to 28°C.
  • DO NOT store below 20°C or above 45°C.

Transportation

To prevent loss or injury, strictly follow operation rules. Keep small parts or wires away from children's reach. DO NOT let children touch the small parts of the T10.

Troubleshooting (FAQ)

Q: What is the Video/Data distance of T10 transmission?
A: Under an open area, the maximum video link distance is 10km, while the data link distance is 20km.
Q: Does T10 support PPM, SBUS?
A: Yes! The SBUS port is defaulted in the first row. If you need a PPM signal, it can be switched in the Device Helper App.
Q: How are the two antennas on T10 defined?
A: Both antennas are part of a 2.4GHz redundant design. Diversity technology is used, so both antennas perform data link and transmission.
Q: How are the two antennas on the receiver defined?
A: The two antennas on the receiver are for redundant design and telemetry.
Q: No LED indication on the receiver when plugged into the flight control board?
A: First, check if the T10 is powered off. If the issue persists, check the battery status (short press the power switch to check the battery level). If not bound, then bind it.
Q: What is the definition of the sound buzzer?
A: 3 short beeps indicate power on. 4 short beeps indicate successful binding. Continuous short beeps indicate low battery level. Slow continuous beeps indicate the receiver is not turned on or disconnected.
Q: Does T10 bind with a new receiver?
A: The T10 sends a binding signal with an ID to bind a new receiver. Once a new one is bound, the old receiver will need to be rebound afterwards.
Q: How many times are commands sent per second?
A: 300 times per second.
Q: Where can I watch demonstration videos of the T10?
A: Please visit www.skydroid.xin to watch the videos.

User Tips

  • The Skydroid T10 system is versatile and can be used not only for UAVs, helicopters, fixed-wing aircraft, and multi-rotors but also for RC cars and boats, expanding its utility for various remote-controlled applications.
  • Always perform a thorough pre-flight check of all equipment and ensure necessary maintenance and repairs are carried out to prevent issues during operation.
  • When handling the remote control, be mindful of the antennas and electronic components. Avoid applying unnecessary force to prevent damage and ensure consistent performance.

Firmware Updates & Support

Firmware Update Procedure

  1. Download and install the "Device Helper" APP before upgrading.
  2. **T10 Upgrade**: Connect the T10 to your phone via Bluetooth. Turn off the main unit, then press and hold button "A" and long press the power button to turn it on. Button "A"'s light will flash slowly, indicating it's downloading. Open the Skydroid Device app, click "updating", choose "update the controller", and click "checking updating". If new firmware is available, click "update at once".
  3. **R10 Upgrade**: Connect the R10 to your phone via Bluetooth. Ensure the main unit is on and paired with the R10 (green indicator light turning on). Open the Skydroid Device app, click "updating", choose "update the receiver", and click "checking updating". If new firmware is available, click "update at once".

Downloading Skydroid Apps

If direct download fails, search for the apps on www.skydroid.xin.

  • **Device Helper**: Used for adjusting radio parameters, firmware upgrades, saving models, and changing modes.
  • **Skydroid FPV**: Used for linking Skydroid video, floating window display (requires enabling floating window feature in Android), VR, video capture, and data rate adjustment.
  • **Skydroid Tower**: Optimized by Tower 4.0, can connect to MAVLink protocol of APM, PX4 flight controller for waypoint data telemetry. Also features a video serial port.
Demonstration of the Skydroid T10's digital map transmission and video feed, showing aerial views and flight data overlay.

FCC Statement

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

  • Reorient or relocate the receiving antenna.
  • Increase the separation between the equipment and receiver.
  • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
  • Consult the dealer or an experienced radio/TV technician for help.

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference. (2) This device must accept any interference received, including interference that may cause undesired operation. Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.

Additional Resources

A comprehensive user manual in PDF format is available for download. Please visit the official Skydroid website for the latest version and additional support materials.

Official Website: www.skydroid.xin

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.