E-ACE K01

Contents

E-ACE K01 TPMS Wireless Tire Pressure Monitoring System User Manual

Intelligent Solar Sensor Auto Security Alarm Device

1. Product Overview

Thank you for purchasing the E-ACE Tire Pressure Monitoring System (TPMS). This system is designed to enhance driving safety by providing real-time monitoring of tire pressure and temperature. It alerts the driver with a warning sound and a flashing icon if any abnormal tire conditions are detected, helping to prevent accidents and ensure the safety of all occupants.

Important Reminder: Please read this manual carefully before use. It is not recommended to change machine parameters unless absolutely necessary. The diagrams are for reference only; refer to the actual product for details. Ensure the host unit is powered on before installation.

2. Setup Instructions

2.1. Main Unit Placement

Place the main unit on a suitable position on the left side of the center console. The unit comes with adhesive on its bottom for secure mounting. The product does not require manual turning on or off.

2.2. External Sensor Installation (K01 Model)

Before installing external sensors, press and hold the left button of the host to turn on its power.

  1. Screw the anti-theft nut onto the tire valve nozzle first.
  2. Install the sensor onto the valve according to its marked position (e.g., FL for Front Left) and tighten it.
  3. Screw the anti-theft nut back against the sensor and tighten it firmly with the provided wrench.

If no pressure is displayed for a sensor on the host unit, reinstall that sensor.

External Sensor Installation Steps
Figure 1: External Sensor Installation Steps. (a) Screw in anti-theft nut first, (b) Tighten the sensor, (c) Screw the anti-theft nut counter-clockwise against the sensor, (d) Tighten the sensor and anti-theft nut with a wrench.

2.3. Internal Sensor Installation (K02 Model)

Before installing internal sensors, press and hold the left button of the main unit to turn on its power.

  1. Install the sensor into the tire according to its position.
  2. Replace the original car valve with the sensor.
  3. Inflate the tires sequentially after installation. Ensure tires are fully inflated when the main unit is turned on.
Internal Sensor Installation
Figure 2: Internal sensor installed inside a tire rim.

3. Operating Instructions

3.1. Interface and Display Description

The main unit features a clear display showing real-time tire pressure and temperature for all four tires, battery status, and charging indicators.

TPMS Display Interface Diagram
Figure 3: TPMS Display Interface. 1. Power/Left button, 2. SET button, 3. Right button, 4. Solar energy, 5. Solar icon, 6. Tire pressure units, 7. Tire temperature, 8. Tire Pressure, 9. Temperature unit, 10. Battery, 11. Clock.

3.2. Button Function Description

  • USB Port: For charging the receiver unit.
  • Power/Left Button: Short press to adjust brightness in standby mode. Long press to turn the unit on/off. In menu mode, use to switch menu items or decrease values.
  • Right Button: Short press to adjust brightness in standby mode. Long press to turn off the alarm. In menu mode, use to switch settings or increase values.
  • SET Button (M Menu/Confirm): Long press to enter menu mode. Short press to confirm selected parameters.

3.3. Basic Functions

  • Default Settings: Factory default tire pressure unit is BAR, temperature unit is °C. Upper pressure limit is 3.2 bar, lower limit is 1.8 bar. Temperature alarm value is 68°C.
  • Backlight: Brightness automatically adjusts based on ambient light intensity, and can also be adjusted manually.

Users can customize parameters. If not modified, the system operates with factory defaults. To enter settings, long press the SET button for 3 seconds. The system will exit settings automatically after 30 seconds of inactivity without saving changes. Long press the SET button after completing settings to return to the main interface.

3.4.1. Unit Setting (Factory Default: Bar, °C)

In standby mode, long press SET for 3 seconds. The 'Bar' icon will appear. Press SET again to enter operable setting state. Use Left/Right buttons to select 'Psi' or 'Bar'. Press SET to confirm. To set temperature units, long press SET for 3 seconds, then press Right once. Press SET to enter operable state. Use Left/Right buttons to select '°C' or '°F'. Press SET to confirm.

Unit Setting Display
Figure 4: Display showing unit setting options (Bar and Psi).

3.4.2. Time Setting (For Models with Clock Function Only)

In standby mode, long press SET for 3 seconds. Press Right twice to enter time setting. Short press SET twice; the hour number will flash. Use Left/Right buttons to adjust hours. Short press SET to set minutes, adjust with Left/Right buttons. Long press SET to exit.

Time Setting Display
Figure 5: Display showing time setting (13:28).

3.4.3. Changing Tire Pressure Limits

Long press SET for 3 seconds. Press Right twice to enter maximum air pressure setting. Press SET once; the pressure number will flash. Use Left/Right buttons to adjust. Long press SET to exit. To set the lower limit, long press SET for 3 seconds, then press Right three times. Press SET once; the pressure number will flash. Use Left/Right buttons to adjust. Long press SET to exit.

Upper Pressure Limit Setting
Figure 6: Display showing upper tire pressure limit setting (3.2 Bar).
Lower Pressure Limit Setting
Figure 7: Display showing lower tire pressure limit setting (1.8 Bar).

3.4.4. Changing Temperature Limits

Long press SET for 3 seconds. Press Right four times to enter tire temperature upper limit setting. Press SET once; the temperature number will flash. Use Left/Right buttons to adjust. Long press SET to exit.

Temperature Limit Setting
Figure 8: Display showing upper temperature limit setting (68 °C).

4. Maintenance

4.1. Single Sensor Replacement and Pairing

First, remove the old sensor and install the new one. In standby mode, long press SET for 3 seconds. Press Right five times to enter pairing selection mode. Press SET once; the '0' on the interface will flash (default is front left wheel). Use Left/Right buttons to select the position (0=front left, 1=front right, 2=rear left, 3=rear right). After selecting, press SET; the number will flash. Install the new sensor on the tire and check for a change in the displayed number. Once changed, long press SET to exit.

  • For built-in sensors, inflate and deflate the tire when the number flashes.
  • Any sensor can be matched to any position during this process.
Sensor Pairing Display 1
Figure 9: Display during sensor pairing (example 1).
Sensor Pairing Display 2
Figure 10: Display during sensor pairing (example 2).
Sensor Pairing Display 3
Figure 11: Display during sensor pairing (example 3).

4.2. External Sensor Battery Replacement

When replacing batteries, disassemble and install one by one to avoid mixing parts. Use CR1632 button batteries (working temperature: -30°C to 80°C).

  1. Prepare a nut wrench. Turn the nut clockwise to separate it from the sensor, then remove the sensor counter-clockwise.
  2. Use a wrench to unscrew the upper cover of the sensor counter-clockwise.
  3. Remove the old battery and dispose of it properly.
  4. Install a new CR1632 lithium battery, ensuring positive (+) side faces upwards.
  5. Screw on the upper cover of the sensor and tighten it clockwise with a wrench.
External Sensor Battery Replacement
Figure 12: External Sensor Battery Replacement. (a) Open outer cover with wrench, (b) Remove old battery and install new CR1632, (c) Close cover and tighten.

5. Troubleshooting

5.1. Restore Factory Settings (Re-pairing)

In the power-on state, long press the SET button for 3 seconds to enter settings. Press the Left button again to enter item 7. Press the SET button twice to reset the machine and restore factory settings. The system will then search for sensors again. To update sensors, install new sensors on the valve or drive the car at 30 km/h or more after resetting. After 10-30 minutes, the host will automatically search for sensor signals. Pairing is complete once all 4 sensors are found. Manually set data will revert to factory settings.

Factory Reset Display
Figure 13: Display showing factory reset confirmation.

5.2. Sensor Not Displaying Pressure

  • Ensure the sensor is correctly installed and tightened. Reinstall if necessary.
  • Check if the sensor battery is dead (for external sensors, replace CR1632).
  • Perform a factory reset and re-pair the sensors.
  • Ensure the main unit is powered on and charged.

5.3. Incorrect Readings

  • Verify tire pressure with a reliable gauge.
  • Ensure sensors are correctly assigned to their respective tire positions.
  • Check for strong electromagnetic interference nearby.

6. Specifications

FeatureSpecification
BrandE-ACE
Model NameK01/K02
Special FeaturesSolar Energy Charging
Voltage5V
MaterialPlastic
Item TypeAlarm Systems & Security
CertificationsRoHS, FCC, EEC, CE, CCC, CC
Batteries IncludedYes
External Sensor Battery TypeCR1632
External Sensor Working Temperature-30°C to 80°C
Item Length77 mm
Item Width81 mm
Item Height26 mm
Item Weight0.4 kg
TPMS Unit Dimensions
Figure 14: Detailed diagram of the TPMS display unit with dimensions and labeled components.

7. User Tips

  • Automatic Activation: The unit features a 'shake awake' function, so you generally don't need to turn it on manually.
  • Solar Charging: The solar panel effectively keeps the unit charged, reducing the need for USB charging.
  • Easy Installation: Many users find the installation process intuitive and straightforward.
  • Sensor Installation Order: For external sensors, always install the anti-theft nut first, then the sensor, and finally tighten the nut against the sensor.
  • Setup Patience: While setup is generally easy, some users note that learning the sequence for tightening and indicator settings might take a little patience.
  • Modern Charging: The Type-C USB port is a convenient and modern charging solution.

8. Frequently Asked Questions (FAQ)

Q: Is this TPMS compatible with my car model?
A: The E-ACE TPMS is designed for broad compatibility and can be used with most cars, SUVs, ORVs, MPVs, Minibuses, and Wagons.
Q: Does the battery recharge with sunlight?
A: Yes, the main unit is equipped with a solar panel for convenient solar charging.
Q: Can the batteries in the external sensors be changed?
A: Yes, the external sensors use replaceable CR1632 button batteries. Refer to Section 4.2 for instructions.
Q: What is the maximum pressure it can monitor?
A: The default upper pressure limit is 3.2 Bar, but this value is adjustable through the settings menu (refer to Section 3.4.3).
Q: Can I purchase internal sensors separately if one fails?
A: Please contact customer support or the seller for availability of individual replacement sensors.

9. Warranty and Support

For warranty information, technical support, or service inquiries, please refer to the product packaging or contact your retailer. Keep your purchase receipt for warranty claims.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.