1. Introduction
The TinySA is a compact and portable spectrum analyzer designed for measuring and analyzing radio frequency signals. It features a 2.8-inch display and supports frequency ranges from 100kHz to 960MHz, making it suitable for various applications including mid-frequency, high-frequency, and very high-frequency UHF analysis. This manual provides essential information for setting up, operating, and maintaining your TinySA device.
2. Package Contents
Please inspect the package carefully to ensure all items are present and undamaged:
- TinySA Spectrum Analyzer unit
- USB-C Cable
- 2x SMA Male to Male RF Cables
- Telescopic Antenna
- SMA Male to Female Adapter
- Lanyard
3. Setup
3.1 Initial Charging
Before first use, fully charge the TinySA unit. Connect the device to a 500mA minimum USB port or USB charger using the provided USB-C cable. A full charge typically takes a maximum of 1 hour.
3.2 Basic Connections
The TinySA features two RF input ports: 'HIGH' and 'LOW'.
- LOW Input: For frequency ranges from 100kHz to 350MHz.
- HIGH Input: For frequency ranges from 240MHz to 960MHz.
Connect the appropriate antenna or signal source to the corresponding input port using the provided SMA cables or adapters. Ensure connections are secure.
4. Operating Instructions
4.1 User Interface
The TinySA features a 2.8-inch resistive touch display with 320x240 pixel resolution and 16 bits per RGB pixel. Navigation and control are primarily done via the resistive touch screen and a jog switch. A USB serial port is available for control, and an optional TTL USART port (software not yet implemented) is on the internal PCB.
4.2 Modes of Operation
The TinySA supports various input and output modes, each with specific frequency ranges and capabilities:
4.2.1 Low Input Mode
- Input Frequency Range: 100kHz to 350MHz.
- Input Impedance: 50 ohm when input attenuation is set to 10dB or more.
- Attenuation: Selectable manual and automatic input attenuation between 0dB and 31dB in 1 dB steps.
- Absolute Maximum Input Level: +10dBm without attenuation.
- Absolute Maximum Input Power: +20dBm for short periods with 30dB attenuation.
- Resolution Filters: Manually selectable filters of 3, 10, 30, 100, 300, 600kHz, with automatic selection from 57 resolution filters.
4.2.2 High Input Mode
- Input Frequency Range: 240MHz to 960MHz.
- Note: Strong signals outside the 240MHz to 960MHz range can cause distortion of in-band signals due to the absence of an input bandfilter.
4.2.3 Low Output Mode
- Output Type: Sinus output with harmonics below -40dB of fundamental.
- Output Frequency Range: 100kHz to 350MHz.
- Output Level: Selectable in 1dB steps between -76dBm and -6dBm.
- Modulation: Optional AM, narrow FM, and wide FM modulation or slow sweep over selectable frequency span.
4.2.4 High Output Mode
- Output Type: Square wave output.
- Output Frequency Range: 240MHz to 960MHz.
- Output Level: Selectable in variable increments between -38dBm and +13dBm.
- Modulation: Optional narrow FM and wide FM modulation or slow sweep over selectable frequency span.
4.2.5 Reference Generator
- Output Type: Optional square wave output with fundamental at -25dBm connected to high input/output.
- Frequency Options: Can be set to 1MHz, 2MHz, 4MHz, 10MHz, 15MHz, or 30MHz.
5. Maintenance
5.1 Cleaning
To clean the device, use a soft, dry cloth. For stubborn dirt, a slightly damp cloth with mild soap can be used, ensuring no liquid enters the device openings. Do not use abrasive cleaners or solvents.
5.2 Battery Care
The TinySA operates on a fully charged battery for at least 2 hours. To prolong battery life, avoid extreme temperatures and store the device with a partial charge if not used for extended periods.
5.3 Firmware Updates
Periodically check for and install firmware updates to ensure optimal performance and access to new features. Firmware updates often include bug fixes and performance improvements. Refer to the official TinySA website or support resources for instructions on how to update the firmware.
6. Troubleshooting
6.1 Device Not Powering On
- Ensure the battery is fully charged.
- Verify the USB-C cable and power source are functioning correctly.
6.2 Display Interference
Users have reported potential display interference, particularly in the LW, MW, and SW bands. If you experience significant interference, try to operate the device away from other electronic devices or sources of electromagnetic noise. Adjusting display brightness or settings might also help in some cases.
6.3 Inaccurate Readings
- Perform a self-test or calibration if available in the device menu.
- Ensure correct input mode (LOW/HIGH) is selected for the frequency range being measured.
- Check all cable connections for tightness and integrity.
7. Specifications
| Feature | Specification |
|---|---|
| Display | 2.8-inch, 320x240 pixels, 16 bits per RGB pixel, Resistive touch control |
| Input Frequency Range (Low) | 100kHz to 350MHz |
| Input Frequency Range (High) | 240MHz to 960MHz |
| Input Impedance | 50 ohm (when attenuation ≥ 10dB) |
| Input Attenuation | 0dB to 31dB in 1dB steps (manual/automatic) |
| Max Input Level (without attenuation) | +10dBm |
| Max Input Power (30dB attenuation) | +20dBm (short period) |
| Output Frequency Range (Low) | 100kHz to 350MHz (Sinus output) |
| Output Frequency Range (High) | 240MHz to 960MHz (Square wave output) |
| Battery Operation | At least 2 hours on a fully charged battery |
| Charging Time | Max 1 hour (with 500mA minimum USB port/charger) |
| Dimensions (L x W x H) | 90mm x 60mm x 15mm (3.5in x 2.4in x 0.6in) |
| Package Weight | 0.259 kg |
8. User Tips
- Familiarization: Take time to learn the device's functions and interface. The TinySA has many capabilities that require understanding to utilize effectively.
- Firmware Updates: Regularly check for and apply firmware updates. These often improve performance and add new features.
- Quick Scans: The TinySA is highly effective for quick scans and initial assessments of RF environments.
- Minimize Interference: If experiencing display interference, especially in lower frequency bands, try to isolate the device from other electronics.
- Consult Resources: For in-depth understanding and advanced usage, refer to the comprehensive user manual PDF and online communities.
9. Warranty and Support
For detailed information regarding warranty, technical support, and advanced operational guides, please refer to the official user manual PDF. This document contains comprehensive instructions and troubleshooting steps not fully covered in this brief overview.
You can access the full user manual PDF here: TinySA User Manual (PDF)
For further assistance, please contact the seller or refer to the official TinySA support channels.