Chevolink DS-1021ZC

Contents

Chevolink DS-1021ZC Smart ZigBee Light Switch User Manual

Model: DS-1021ZC | Brand: Chevolink

1. Introduction

This manual provides comprehensive instructions for the installation, operation, and maintenance of your Chevolink DS-1021ZC Smart ZigBee Light Switch. This smart switch is designed to integrate seamlessly with your smart home ecosystem, offering APP control and voice control capabilities through platforms like Tuya, Amazon Alexa, and Google Home. It supports both neutral wire and no-neutral wire installations, eliminating the need for a capacitor in most cases.

2. Safety Information

WARNING: Disconnect power at the circuit breaker before installation, wiring, or maintenance. Failure to do so may result in serious injury or death.

  • Basic electrical wiring knowledge or experience is required. If you are unsure, please consult a professional electrician.
  • This product supports only one-way/single-pole circuits and is not compatible with 2-way circuits.
  • The ON/OFF button can also be used as a reset button. Long press any key for 10 seconds to reset your smart switch to factory defaults. Only perform this if you are sure you want to erase all your settings.
  • Ensure the output is connected to a bulb when the single-fire switch is working. Do not leave any output empty if the bulb's power is less than 3W.
  • For multi-gang switches, connect to as many bulbs as possible (e.g., two-way switch to two bulbs, three-way to three bulbs, four-way to four bulbs). The driving energy of the single-fire switch is provided by the bulb; higher bulb power provides more energy.

3. Package Contents

Please check the package for the following items:

  • Chevolink DS-1021ZC Smart ZigBee Light Switch
  • User Manual (this document)

4. Specifications

Product dimensions and specifications table

Image: Product dimensions and detailed specifications.

Product Specifications
FeatureDescription
Product NameZigBee switch
Product ModelDS-1021ZC
Product ColorBlack/White/Gold/Grey (Available options)
Support SystemAlexa/Google Home
Input Voltage100-240VAC 50/60Hz
Control MethodAPP Control/Voice Control
Operating Temperature-20°C~50°C
Product Size86*86*35mm (EU Standard)
Power Rating3-600W
Wireless StandardsZigbee (IEEE 802.15.4)
Button Life100,000 times
Package Size106*100*51mm
Product Weight218g
Product MaterialABS+PC
Current10A
CertificationRoHS, FCC, CE

5. Setup Instructions

5.1. Download App and Register

  1. Download the Smart Life App: Scan the QR code below or search for "Smart Life" in your device's app store (iOS App Store or Google Play Store).
    QR code for Smart Life App download

    Image: QR code for Smart Life App download (iOS & Android System).

  2. Register and Log In: Open the Smart Life App. Enter your phone number or email, select your country, obtain a verification code, and set your password to register.
    Smart Life App registration screen

    Image: Smart Life App registration process.

  3. Create a "Family": Enter your family name and select the rooms within your home. This helps organize your smart devices.
    Smart Life App 'Create Family' screen

    Image: Smart Life App 'Create Family' setup.

5.2. Wiring Diagram

Please select the appropriate wiring method based on your actual electrical setup. Always disconnect power at the circuit breaker before performing any wiring.

Wiring diagram for Smart Zigbee Switch with and without neutral wire

Image: Universal wiring diagram for single-fire (no neutral) and zero-fire (with neutral) installations.

5.2.1. EU Switch Wiring Method

A. Need Neutral Wire:

  1. Live Wire connects to the 'L' terminal.
  2. Bulb Wire connects to the 'L1', 'L2', 'L3', 'L4' terminals (depending on gang count).
  3. Neutral Wire connects to the 'N' terminal.
  4. One-way switch connects 'L1' terminal.
  5. Two-way switch connects 'L1', 'L2' terminals.
  6. Three-way switch connects 'L1', 'L2', 'L3' terminals.
  7. Four-way switch connects 'L1', 'L2', 'L3', 'L4' terminals.

B. No Need Neutral Wire:

Attention: If there is no neutral wire, a capacitor must be connected.

  1. Live Wire connects to the 'L' terminal.
  2. Bulb Wire connects to the 'L1', 'L2', 'L3', 'L4' terminals.
  3. A capacitor must be connected between the 'L1', 'L2', 'L3', 'L4' (depending on gang count) and the neutral wire of the bulb.
  4. One-way switch connects 'L1' terminal.
  5. Two-way switch connects 'L1', 'L2' terminals.
  6. Three-way switch connects 'L1', 'L2', 'L3' terminals.
  7. Four-way switch connects 'L1', 'L2', 'L3', 'L4' terminals.

5.2.2. US Switch Wiring Method

The US wiring method is similar to the EU method. Please refer to the diagram above.

A. Need Neutral Wire:

  1. Live Wire connects to the 'L' terminal.
  2. Bulb Wire connects to the 'L1', 'L2', 'L3', 'L4' terminals.
  3. Neutral Wire connects to the 'N' terminal.
  4. One-way switch connects 'L1' terminal.
  5. Two-way switch connects 'L1', 'L2' terminals.
  6. Three-way switch connects 'L1', 'L2', 'L3' terminals.
  7. Four-way switch connects 'L1', 'L2', 'L3', 'L4' terminals.

B. No Need Neutral Wire:

Attention: If there is no neutral wire, a capacitor must be connected.

  1. Live Wire connects to the 'L' terminal.
  2. Bulb Wire connects to the 'L1', 'L2', 'L3', 'L4' terminals.
  3. A capacitor must be connected between the 'L1', 'L2', 'L3', 'L4' (depending on gang count) and the neutral wire of the bulb.
  4. One-way switch connects 'L1' terminal.
  5. Two-way switch connects 'L1', 'L2' terminals.
  6. Three-way switch connects 'L1', 'L2', 'L3' terminals.
  7. Four-way switch connects 'L1', 'L2', 'L3', 'L4' terminals.

5.3. Connecting APP with Smart Gateway Device

  1. Open the Smart Life App, click "Add Device", and find the corresponding gateway device in the "Gateway Central Control" column.
  2. Reset the gateway device by long-pressing the reset button until the indicator light (green light) is continuously on.
  3. Confirm that the two green lights are on, then click "Next". Ensure your mobile phone and gateway are on the same network for successful connection.
  4. Once the device is added successfully, click "Done".
Smart Life App gateway connection steps

Image: Steps to connect the Smart Life App to a smart gateway device.

5.4. Connecting to the Smart Switch

  1. Ensure the switch is powered. Press any switch button for 10 seconds until the red WiFi indicator light flashes rapidly.
  2. After the smart gateway is connected to the APP, click "Add sub-device" and then click "LED already blinking".
  3. The device will connect automatically. Click "Done" to complete the connection.
Smart Life App switch connection steps

Image: Steps to connect the smart switch to the Smart Life App via the gateway.

6. Operating Instructions

6.1. Functional Features

  • Ultra-low Power Consumption: The switch itself consumes less than 0.05W.
  • Timing Function: Set schedules to automatically turn the switch ON or OFF at specific times.
  • Power-on State Setting:
    • Power Failure: Switch is always OFF when power is restored after an outage.
    • Power On: Switch is always ON when power is restored after an outage.
    • Power-off Memory: The switch remembers its state before a power cut and restores it when power is back.
  • Indicator Light Control:
    • Turn Off: The indicator light is always OFF, regardless of the switch's state.
    • Indicate State: The indicator light is OFF when the switch is ON, and ON when the switch is OFF.
    • Indicate Position: The indicator light is OFF when the switch is ON, and ON when the switch is OFF.
  • Multi-control Correlation: Allows for advanced control scenarios with other smart devices.

6.2. Smart Speaker Voice Control

Control your smart switch hands-free using voice commands with compatible smart speakers.

Smart speaker voice control with Alexa and Google Home

Image: Examples of voice commands for Alexa and Google Home.

6.3. Backlight ON/OFF Option

The switch features a backlight that can be turned ON or OFF, allowing you to create a comfortable sleeping environment.

Backlight ON/OFF option for the smart switch

Image: Visual representation of the backlight ON and OFF states.

6.4. APP Control

Utilize the Smart Life app to control your switch remotely, set schedules, create scenes, and integrate with other smart devices.

7. Maintenance

  • Cleaning: Wipe the switch surface with a soft, dry cloth. Do not use abrasive cleaners or solvents.
  • Battery Replacement: If your switch is a scene switch model (not a wired light switch), it typically uses a CR2032 button battery. Replace the battery when the device's performance degrades or it stops responding. Ensure correct polarity when inserting the new battery.

8. Troubleshooting

  • Flickering/Dimming Bulbs or Unstable Switch: If bulbs below 3W are used, they may flicker or the switch might not start. If this occurs, first try connecting a neutral wire. If a neutral wire is not available, connect a capacitor in parallel with the neutral wire and the live wire of the bulb. This is especially common with high-voltage LED strip lamps, high-voltage LED bulbs, or high-voltage LED ceiling bulbs that lack drivers or capacitors.
  • Switch Not Starting: Ensure the switch is correctly wired and receiving power. Check the circuit breaker. If it's a scene switch, check the battery.
  • Connectivity Issues: Ensure your gateway and switch are within Zigbee range. Check your Wi-Fi router and gateway connection. Try resetting the switch (long press any button for 10 seconds) and re-pairing it with the gateway.
  • App Control Issues: Ensure your Smart Life app is updated to the latest version and your phone has a stable internet connection.

9. User Tips

  • Battery for Scene Switches: Note that CR2032 button batteries are typically not included with scene switches due to shipping regulations. Have one ready for installation.
  • Home Assistant Integration: This switch works reliably with Home Assistant, especially when integrated via Zigbee2MQTT. It offers single click, double click, and long press commands.
  • Long Press Duration: The long press command is usually triggered upon release after holding for approximately 3-4 seconds. This duration is fixed and cannot be adjusted.
  • Click Sound: The switch has a noticeable click sound, which some users might find a bit loud.
  • Native ON/OFF Toggle: For a single light, a simple click might not natively toggle ON/OFF. You may need to create specific programming or use Home Assistant automations for this functionality.

10. Warranty and Support

This product comes with a 1-Year Warranty from the date of purchase. For technical support, troubleshooting, or warranty claims, please refer to the official seller's contact information or the Smart Life app support section.

A detailed user manual in PDF format is also available for download: View User Manual (PDF)

11. Compliance

This device complies with relevant safety and environmental standards. Certifications include:

  • RoHS: Restriction of Hazardous Substances
  • FCC: Federal Communications Commission
  • CE: Conformité Européenne
Documents and downloads

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.