ZOOM HB-876E

Contents

ZOOM HB-876E E-Bike 4-Piston Hydraulic Disc Brake Set User Manual

Model: HB-876E

1. Introduction

This manual provides detailed instructions for the installation, operation, maintenance, and troubleshooting of your ZOOM HB-876E 4-Piston Hydraulic Disc Brake Set. Please read this manual thoroughly before installation and use to ensure safe and optimal performance of your braking system.

The ZOOM HB-876E is a high-performance 4-piston hydraulic disc brake system designed for E-bikes, electric scooters, and MTB, offering enhanced braking power and durability.

ZOOM HB-876E E-Bike Brake Set

Figure 1.1: ZOOM HB-876E E-Bike 4-Piston Hydraulic Disc Brake Set

2. Safety Warnings and Precautions

WARNING: Failure to follow these instructions could result in serious injury or death.

  • High Temperature: The caliper body and disc can reach high temperatures during and immediately after braking. Do not touch these parts to avoid burns. Allow them to cool sufficiently before any repair or adjustment.
  • Braking Distance: Braking distance increases significantly in wet conditions. Reduce speed and brake cautiously in rain or on wet surfaces to prevent skidding and falls.
  • Pre-Ride Check: Always ensure the brake system operates correctly before each ride.
  • Contamination: Keep the disc and brake blocks free from oil or grease. Oil contamination will severely impair braking performance. If brake blocks are contaminated, replace them. If the disc is contaminated, clean it thoroughly.
  • Brake Block Thickness: Ensure brake block thickness is more than 0.8mm before riding. Replace worn brake blocks immediately (refer to Figure 1-1 in the PDF manual for replacement marks).
  • Brake Fluid: Use only ZOOM mineral oil (compatible with Shimano and Yannao mineral oil). Using other brake fluids can cause brake failure, air lock, or system damage.
  • Air Lock Phenomenon: Avoid frequent braking. Do not mix water or air bubbles into the brake system. Air lock can cause sudden brake action.
  • Vehicle Orientation: The ZOOM system is not designed for inverted vehicle states. If the vehicle has been inverted or placed horizontally for an extended period, check brake function before riding.
  • Oil Leakage: If oil leakage occurs, stop using the brake system immediately and repair it. Continued use with oil leakage is dangerous.
  • Quick Release Handle: Ensure the quick release handle is on the right side (opposite to the disc) to prevent collision with the disc.
  • Parts Compatibility: Use only ZOOM standard parts for optimal performance and safety.
  • Tightening Torque: Ensure all screws and nuts are tightened to the specified torque. Loose components can lead to accidents.

2.1 Mineral Oil Handling Precautions

  • Eye Contact: Wear safety glasses. If mineral oil enters eyes, flush immediately with large amounts of clean water and seek medical attention.
  • Skin Contact: Wear protective gloves. If mineral oil touches skin, wash thoroughly with soap and water.
  • Inhalation: Use in a well-ventilated area. If you feel unwell after inhaling oil and gas, move to fresh air.
  • Ingestion: Do not drink mineral oil. If ingested, it may cause diarrhea and vomiting. Seek medical attention immediately.
  • Storage: Keep out of reach of children. Store in a sealed container, away from direct sunlight, in a cool, dark place, free from foreign matter and moisture.
  • Waste Oil: Dispose of waste oil according to local regulations and legal methods.

3. Setup (Installation)

This section details the installation process for your ZOOM HB-876E hydraulic disc brake system.

Video 3.1: Product overview and component demonstration.

3.1 Disc Installation

  1. Install the disc on the flower drum. Ensure the ZOOM logo on the disc faces outward (the rotation direction of the wheel must be consistent with the arrow direction on the disc).
  2. Loosely tighten the disc fixing screws to a half-tight state.
  3. To ensure the flatness of the disc, tighten the disc screws alternately in a diagonal pattern.
  4. Apply a certain force to the disc clockwise and lock the disc fixing screws in diagonal order.
  5. Disc Fixing Screw Locking Torque: 40-60 kgf-cm (35-52 lb-in).

3.2 Caliper Body Assembly

  1. Install the front or rear disc brake conversion seat onto the screw hole of the support.
  2. Loosen the fixing screws of the caliper body to allow it to be in a fine-tuning state.
  3. Install the conversion seat onto the frame.
  4. Transfer Seat Fixing Screw Locking Torque: 70-90 kgf-cm.

3.3 Disc Handle Assembly

  1. Fix the disc handle first. Loosely tighten one screw, then fully tighten the other screw, and finally tighten the first screw.
  2. Disc Brake Handle Locking Torque: 60-80 kgf-cm (52-69 lb-in).
  3. Hold the disc handle under pressure and lock the fixing screws of the disc caliper body while the disc is pressed by the disc block.
  4. Pump the disc brake several times to confirm normal brake action and no oil leakage.
Brake Lever Cable Length and Connector

Figure 3.2: Brake lever with 45mm cable length and connector detail.

Brake Lever Dimensions and Adjustment

Figure 3.3: Brake lever dimensions (90mm length, 22.2mm clamp) and brake stroke adjustment screw.

4. Operating (Adjustments)

4.1 Adjustment of Brake Block and Disc Brake Caliper Body

The ZOOM disc brake system automatically adjusts the clearance between the disc and brake block as the piston is gradually pushed out due to wear. When replacing brake blocks, the piston must be pressed vertically to the bottom using a slotted screwdriver.

If the piston moves unevenly, or the brake block interferes with the disc, refer to the brake block replacement steps (Figure 2-5 in the PDF manual).

4.2 Adjustment of Hand Grip Distance

Use a 2mm hex wrench to adjust the grip distance:

  • Turn clockwise to increase grip distance (maximum ~100mm).
  • Turn counter-clockwise to decrease grip distance (minimum ~80mm).
  • If the 2mm hex wrench is turned clockwise beyond the maximum grip distance, the aluminum piston of the handle will move forward, increasing braking force but potentially disabling automatic oil replenishment.

4.3 Tubing Cutting

If the oil pipe length is too long, it must be cut and adjusted. Necessary tools include an 8mm open-end wrench, tubing cutting tool, oil pipe joint screw, oil pipe hold-down nut, tubing copper sleeve, and oil needle.

  1. Push the oil pipe fixing screw sheath towards the oil pipe. Use an 8mm open-ended wrench to unscrew the oil pipe fixing screw (Figure 4-1 in the PDF manual). Be aware of brake oil leakage.
  2. Determine the required oil pipe length. Cut off the excess length with the tubing cutting tool (at least 15mm should be cut off), ensuring the cut is vertical to the oil pipe axis.
  3. Insert the oil pipe, copper sleeve, and oil pipe bushing (with type ring) into the oil pipe in sequence. Ensure the smaller end of the copper sleeve is fixed to the oil pipe, then press the oil pipe bushing into the oil pipe (Figure 4-2 in the PDF manual).
  4. Press the front end of the oil pipe into the front end of the disc handle until it is fully seated. While pressing the oil pipe, lock the oil pipe fixing screw on the disc handle with an 8mm open-ended wrench (Figure 4-3 in the PDF manual).
  5. Locking Torque of Oil Pipe Fixing Screw: 80-100 kgf-cm (6-10 NM).

4.4 Oil Replenishment Operation

Replenish oil when the oil level in the oil groove is insufficient, or the brake block is worn, preventing the disc brake handle from being held firmly.

Necessary tools include a T15 M-shaped wrench, 8mm open-end wrench, oil groove sealing screw, caliper oil inlet screw, oil needle cylinder, transparent hose, and oil storage bottle.

  1. Make the oil groove parallel to the ground. Remove the sealing screw of the oil groove with a T15 M-shaped wrench.
  2. Insert the transparent hose into the upper end of the M6 oil nozzle and connect the other end to the plastic hose.
  3. Draw an appropriate amount of vehicle oil from the oil storage tank with the transparent hose connected to the oil needle cylinder. Ensure no bubbles are in the hose.
  4. Insert the oil needle cylinder into the upper body oil inlet nozzle.
  5. Use an 8mm open-ended wrench to tighten the loading body oil inlet nozzle (clockwise for about 1.5 turns).
  6. Formal Oil Replenishment: Press the brake handle until no bubbles are discharged from the needle cylinder hose. If the effect is not obvious, press the needle cylinder by hand to make brake oil enter the disc brake, then pull the needle cylinder to discharge bubbles. Repeat 3-5 times. Press and release the brake handle until no bubbles are discharged.
  7. Take out the needle cylinder, put the oil nozzle at the main end, and lock the oil injection screw.
  8. Hold the disc brake handle several times to make the grip feel solid.
  9. Remove the hose at the end of the caliper body (careful not to stain brake block or disc with oil). Then remove the hose at the handle end and replace the M6 oil nozzle with the oil groove sealing screw.
  10. Locking Torque of Oil Groove Sealing Screw: 30-40 kgf-cm.
  11. Clean oil-stained parts with alcohol or a clean cloth. Return the disc brake handle to its original position.
  12. Replace the oil if it changes color significantly.

5. Maintenance

To maintain optimal performance of your ZOOM hydraulic disc brake system, perform the following inspections:

5.1 Before Riding

  • Brake Block: Confirm that the thickness of the brake block has not reached the lower limit (0.2mm). Check for replacement marks; if visible, replace with new brake blocks.
  • Oil Pipe: Check the oil pipe for cracks, wear, deformation, or damage. Replace if any issues are found.

5.2 After Riding

  • Disc Cleaning: If dirt or impurities are present between the disc brake caliper body and the disc, clean them after riding. Avoid staining the disc or brake block with oil.

5.3 Periodic Inspection

  • Lubrication: Lubricate the connecting rod of the disc brake handle regularly.
  • Locking Screws: Check that all screws are tight and maintain the originally set locking torque.

5.4 General Maintenance Guidelines

  • Keep rotors and brake pads away from any lubricants, as they are easily affected by oil.
  • The rotor and brake pads require a 'running-in' period of 20 to 40 braking cycles to achieve full braking force.
  • Replace brake pads when their thickness is less than 3 mm or when the pad surface is parallel to the warning brake pad channel of the caliper body.
  • Clean the caliper housing thoroughly before mounting new brake pads.

6. Troubleshooting

This section provides solutions to common issues you might encounter with your ZOOM HB-876E brake system.

ProblemPossible CausesSolution
Braking NoiseFriction between brake block and disc; Incorrect adjustment of brake block or caliper body; Disc deformation or bendingReadjust brake block/caliper body (refer to Chapter 1 of PDF); Replace disc (refer to Chapter 2 of PDF)
Poor GripAir exists in the system; Insufficient oilLoosen oil groove sealing screw and pump handle to exhaust air; Replenish brake oil (refer to Section 4.4)
Loose Transfer SeatLoose fixing screws of the adapterLock the fixing screws of the adapter (refer to Chapter 2 of PDF)
Brake Handle Presses to Driver's HandleInsufficient oilReplenish brake oil (refer to Section 4.4)
Oil LeakageDamaged seal or fittingCheck oil leakage part and repair or replace
Insufficient or No Braking ForceBrake block is polluted or contaminated; Contaminated or oily discsThoroughly clean and dry discs with alcohol and clean cloth; Replace brake blocks

7. Specifications

Here are the detailed specifications for the ZOOM HB-876E 4-Piston Hydraulic Disc Brake Set:

FeatureDescription
Product NameZOOM Disc Brake
Model NumberHB-876E
Braking SystemHydraulic Disc Brake (Hydraulic Brake Pad)
ComponentsDisc Brake
MaterialHigh strength forged aluminum
Brake OilMineral oil
FeaturesOne-piece design, 4-piston, dual actuation
Mounting CompatibilityIS mount and Post mount are available
Post Mount Dimension75mm
IS Mount Dimension51mm
Front Brake Weight (F160-R140)300g
Rear Brake Weight (F180-R160)320g
Lever Length90mm
Clamp Diameter22.2mm
Cable Length (from lever)45mm
Braking Force Increase25% (compared to double-piston)
Wear Resistance Increase150% (compared to double-piston)
4-Piston Calipers Performance

Figure 7.1: 4-Piston Calipers highlighting increased braking force and wear resistance.

ZOOM HB-876E Black Set

Figure 7.2: ZOOM HB-876E Black 4-Piston Hydraulic Disc Brake Set.

ZOOM HB-876E Red Set

Figure 7.3: ZOOM HB-876E Red 4-Piston Hydraulic Disc Brake Set.

8. User Tips

  • Some users may not immediately notice a significant difference in braking feel compared to 2-piston brakes, especially in the first few weeks of use. Performance benefits often become more apparent over time and in demanding conditions.
  • If you plan to route brake lines internally through your frame, verify if the brake lines are sold disconnected or if you will need to disconnect and re-bleed them after routing.
  • Always confirm the specific side (left/right) of the brake levers you are ordering to match your preference or existing setup.
  • Before purchasing, check the compatibility of the brake set with your specific electric scooter or e-bike model (e.g., Kukirin G2 Master, Laotie ES40) to ensure proper fitment and function.
  • The brake set typically includes brake pads, so you usually won't need to purchase them separately for initial installation.

9. Frequently Asked Questions (FAQ)

  • Q: Are the brake lines pre-connected to the levers and calipers, or are they disconnected for internal frame routing?
    A: The product images suggest the lines are pre-connected. For internal routing, you may need to disconnect, route, and then re-bleed the system.
  • Q: What is the length of the brake cable?
    A: The cable length from the lever is approximately 45mm. The main hydraulic lines will vary in length depending on the specific model ordered (front/rear).
  • Q: What are the dimensions for mounting the rear brake caliper?
    A: The brake set supports both IS mount (51mm) and Post mount (75mm) standards.
  • Q: Which side is the brake lever (left/right)?
    A: Brake sets are typically sold as a pair (front and rear). You should specify your preference for left-hand front or right-hand front when ordering, if options are available.
  • Q: Is this brake set compatible with specific scooter models like Kukirin G2 Master or Laotie ES40?
    A: Compatibility depends on the mounting standards (IS/Post mount), rotor size, and lever clamp diameter of your specific scooter. Please compare the specifications provided in this manual with your scooter's requirements.
  • Q: Does the set include brake pads?
    A: Yes, the ZOOM HB-876E brake set typically includes original resin brake pads pre-installed in the calipers.

10. Warranty and Support

The effective shelf-life period for ZOOM products is one year from the date of purchase. This warranty covers manufacturing defects under normal use. It does not cover damage due to improper installation, misuse, neglect, accidents, or normal wear and tear.

For detailed instructions, diagrams, and further information, please refer to the complete user manual PDF available at: ZOOM HB-876E User Manual (PDF)

For technical support or warranty claims, please contact your retailer or the official ZOOM service center.

© 2024 ZOOM. All rights reserved.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.