1. Introduction
The SUITU Motorcycle TPMS (Tire Pressure Monitoring System) is designed to provide real-time monitoring of your motorcycle's tire pressure and temperature. This system helps enhance riding safety by alerting you to abnormal tire conditions, allowing for timely intervention. It features an easy-to-read LCD display and two external sensors for convenient installation and use.
2. Safety Information
- This product is designed for 12V motorcycle tires.
- Tire safety cannot rely solely on this product. Regular manual checks of tire pressure and condition are essential.
- Do not operate or adjust the monitor while riding. Always pull over to a safe location before making any adjustments or checking readings.
- Ensure all components are securely installed to prevent detachment during operation.
- Keep the device away from extreme temperatures and direct sunlight for prolonged periods.
3. Package Contents
Please check the package to ensure all items are present:
Image: Components of the Motorcycle TPMS, including the receiver, two external sensors, USB cable, holder, anti-proof nuts, and spanner.
- 1x Receiver (Monitor)
- 2x External Sensors (Front: 22G1147, Rear: 22G1350)
- 1x USB Power Cable
- 1x Holder
- 2x Anti-proof Nuts
- 1x Spanner
4. Specifications
| Feature | Specification |
|---|---|
| Brand Name | SUITU |
| Item Type | Alarm Systems & Security |
| Material | ABS |
| Voltage | 2.1 - 3.5V |
| Item Length | 48 mm |
| Item Width | 48 mm |
| Item Height | 27 mm |
| Sensor Working Temperature | -40℃ to 100℃ |
| Sensor Working Humidity | 100% |
| Sensor Working Current | 120mA |
| Sensor Pressure Range | 0-8 BAR (0-115 PSI) |
| Sensor Temperature Range | -40℃ to 120℃ |
5. Setup
5.1 Monitor Installation
The monitor features an easy, wireless design for convenient installation.
Image: The monitor mounted on motorcycle handlebars using the provided holder.
- Attach the holder securely to your motorcycle handlebars.
- Slide the monitor onto the holder until it clicks into place.
5.2 Sensor Installation
Ensure you use the correct sensor for each tire: FRONT (22G1147) for the front wheel and REAR (22G1350) for the rear wheel.
- Unscrew the original valve cap from the tire valve.
- Screw on the anti-proof nut onto the tire valve.
- Screw on the corresponding sensor (FRONT for front, REAR for rear) onto the tire valve.
- Using the provided spanner, tighten the anti-proof nut against the sensor to secure it and prevent theft.
6. Operating Instructions
The monitor will start working automatically when the motorcycle starts and auto power off without operation, saving battery. Data updates every 3 seconds with high pressure precision (0.01 BAR) and high temperature precision (±2°C).
Image: Monitor displaying automatic start/stop functionality and data update speed.
6.1 Monitor Display Overview
Image: Detailed view of the monitor display, indicating time, battery level, tire pressure, tire temperature, and units.
- Time Display: Shows current time.
- Battery Display: Indicates the monitor's battery level.
- Tire Pressure: Displays the pressure for front and rear tires (e.g., 2.45 Bar).
- Tire Temperature: Displays the temperature for front and rear tires (e.g., 36°C).
- Unit: Shows the selected pressure (BAR/PSI) and temperature (°C/°F) units.
- Abnormal Warm Icon: Appears when tire temperature exceeds the set limit.
- Sensor Battery Low Icon: Appears when a sensor's battery is low.
- Host Battery Low Icon: Appears when the monitor's battery is low.
6.2 Basic Operations and Settings
Refer to the video below for visual guidance on settings:
Video: Demonstrates how to turn the monitor on/off, set time, temperature unit, pressure unit, and alarm values.
- Turn On/Off Monitor: Press and hold the "-" button for 3 seconds to turn the monitor on. Press and hold the "-" button for 3 seconds to turn the monitor off.
- Time Setting:
- Press both "-" and "+" buttons simultaneously and hold for 3 seconds to enter time setting mode.
- When AM is flashing, press "-" to select AM, PM, or 24hr mode (24hr is blank).
- Press "+" to set the hour and minutes.
- Press "-" to set the value.
- Press both "-" and "+" buttons again to save and exit setting.
- Temperature Unit Setting:
- Press the "+" button until a beep is heard to enter setting mode.
- Press "+" button once and the temperature unit will flash.
- Then press "-" button to select desired unit (°C or °F).
- Press and hold "+" button for 3 seconds to save and exit setting.
- Pressure Unit Setting:
- Press the "+" button until a beep is heard to enter setting mode.
- Press the "+" button once and the unit will flash.
- Then press "-" button to select desired unit (BAR or PSI).
- Press and hold "+" button for 3 seconds to save and exit setting.
- Rear Tyre Pressure Alarm Setting:
- Press the "+" button until a beep is heard to enter setting mode.
- Press the "-" button three times to enter 2P (rear tire) setting.
- Press the "+" button once and the value will flash.
- Press "-" to set the desired value.
- Press "+" for 3 seconds to save and exit.
- Front Tyre Pressure Alarm Setting:
- Press the "+" button until a beep is heard to enter setting mode.
- Press the "-" button twice to enter 1P (front tire) setting.
- Press the "+" button once and the value will flash.
- Press "-" to set the desired value.
- Press "+" for 3 seconds to save and exit.
- High Temperature Alarm Setting:
- Press and hold "+" button until a beep is heard to enter setting mode.
- Press "-" for four times to enter tyre temperature alarm setting.
- Press "+" one time and the digit will flash.
- Press "-" to desired value and press "+" to save.
- Press and hold "+" for 3 seconds to exit setting.
- Tyre Identification:
- Press "+" button 5 times to enter identification mode.
- Press "-" to select the front tire or rear tire. When selected, "--" will flash.
- Charge or discharge the tire (external type only need to remove or install it).
- When the display makes a beep sound, it means the identification is successful.
- Press "-" to select other tire and follow the same step as above mentioned.
7. Maintenance
7.1 Charging the Monitor
The monitor has a built-in lithium battery and is charged via a USB power cable.
Image: USB power cable and the magnetic charging port on the monitor.
- Connect the USB power cable to the charging port on the monitor.
- A full charge takes approximately one hour and allows for normal use in various climates.
7.2 External Sensor Battery Replacement
The sensors come with batteries pre-installed. Only replace them when necessary.
- Carefully remove the sensor from the tire valve.
- Unscrew the sensor cap.
- Remove the old battery.
- Insert a new CR1632 battery, ensuring correct polarity.
- Reassemble the sensor cap and reinstall the sensor on the tire valve, following the installation steps in Section 5.2.
7.3 Durability and Protection
The monitor is designed with protection in mind, featuring waterproof, dustproof, and stable high-temperature resistance to ensure safety.
Image: The monitor submerged in water, highlighting its waterproof and durable design.
8. Troubleshooting
| Problem | Possible Cause | Solution |
|---|---|---|
| Incorrect Pressure Display | Sensors not correctly identified or calibrated; sensor malfunction. | Perform tire identification (Section 6.2, point 9). Verify actual tire pressure with a reliable gauge and compare. If discrepancies persist, contact support. |
| Sensor Gaskets Loose/Leaking | Gaskets may have shifted or worn out after multiple disconnections/reconnections. | Carefully check the rubber gaskets inside the sensors. Ensure they are properly seated and not damaged. Replace if necessary. |
| No Display/Monitor Not Turning On | Monitor battery is low or depleted. | Charge the monitor using the provided USB cable. |
| Sensor Not Connecting/No Reading | Sensor battery low; sensor not properly installed; interference. | Check and replace sensor batteries if needed. Reinstall sensors ensuring they are tight. Perform tire identification. |
| Constant Alarm Sounding | Tire pressure or temperature is outside the set alarm limits. | Check tire pressure and temperature immediately. Adjust alarm thresholds if they are too sensitive for your riding conditions (refer to Section 6.2). |
9. User Tips
- Ensure sensors are correctly identified to the corresponding tire (front/rear) for accurate readings.
- Regularly check sensor gaskets, especially after inflating tires, to prevent leaks.
- If pressure readings seem inaccurate, try re-identifying the sensors or checking the tire pressure with a reliable gauge.
- Keep the monitor charged, especially before long rides, to ensure continuous monitoring.
10. Frequently Asked Questions (FAQ)
- Q: Does it display the pressure in PSI?
- A: Yes, the pressure unit can be set to either BAR or PSI in the settings menu (refer to Section 6.2, point 4).
11. Warranty and Support
For warranty information or technical support, please contact your retailer or refer to the official SUITU website. A detailed user manual is also available in PDF format for download: