1. Introduction
The KALADA Angel Wing Carpet Projection Light is a universal LED decoration light designed to enhance your vehicle's exterior with a unique 'angel wing' projection. This product serves as a welcome light, creating a clear and charming visual effect on the ground beside your vehicle, particularly at night. It features a high-definition projection pattern with strong light transmittance, suitable for approximately 99% of vehicle models.
This manual provides essential information for the safe and effective installation, operation, and maintenance of your Angel Wing Carpet Projection Light.
2. Package Contents
Please inspect the package contents upon receipt. The standard configuration list includes:
- Projection Lamp Heads (2 units)
- Controllers (2 units)
- Wiring Harnesses
- Drill Bit
- Wire Clips
- Wire Heads (connectors)
Note: The image above illustrates the components and a general wiring layout. Actual wiring may vary slightly based on vehicle type.
3. Installation Guide
Professional installation is recommended for optimal performance and safety. Ensure the vehicle's power is disconnected before beginning installation.
- Choose Mounting Location: Identify a suitable flat surface under the side mirrors or along the side skirt of your vehicle where the projection units can be securely mounted and project clearly onto the ground. Ensure the location allows for proper wiring routing.
- Drill Mounting Holes: Using the provided drill bit, carefully drill the necessary holes at the chosen mounting locations. Ensure the hole size matches the diameter of the projection lamp heads for a snug fit.
- Mount Projection Units: Insert the projection lamp heads into the drilled holes. Secure them firmly in place according to their design (e.g., with nuts, clips, or adhesive if provided).
- Connect Wiring:
- Connect each projection lamp head to its respective controller.
- Route the wiring harnesses from the controllers to the vehicle's power source. The main power wires (typically red for positive, black for negative) should be connected to a 12V power source that activates with the car's welcome light function (e.g., when doors unlock or open).
- Utilize the provided wire clips and wire heads (connectors) to make secure electrical connections. Ensure all connections are insulated to prevent short circuits.
- If additional signal wires (e.g., yellow wires) are present, these may be connected to specific vehicle functions like turn signals or door triggers, depending on desired operation. Consult a professional if unsure.
- Secure Wiring: Use the provided wire clips to neatly secure all wiring along the vehicle's chassis, away from moving parts, heat sources, and areas prone to moisture or damage.
- Test Functionality: Reconnect the vehicle's power. Test the Angel Wing lights by unlocking the car or opening a door to ensure they illuminate and project the pattern correctly.
- Final Adjustments: Adjust the angle of the projection units if necessary to achieve the desired 'angel wing' pattern on the ground.
4. Operating Instructions
The Angel Wing Carpet Projection Light is designed for automatic operation. Once correctly installed and wired to your vehicle's electrical system, the lights will activate under specific conditions, typically:
- When the vehicle doors are unlocked.
- When the vehicle doors are opened.
The projection will display the 'angel wing' pattern on the ground, providing both a decorative effect and additional illumination for entry and exit from the vehicle, especially in low-light conditions.
5. Maintenance
To ensure the longevity and optimal performance of your Angel Wing Carpet Projection Light, follow these simple maintenance guidelines:
- Cleaning: Periodically clean the lens of the projection units with a soft, damp cloth to remove dirt, dust, or road grime that may obscure the projection pattern. Avoid abrasive cleaners.
- Wiring Inspection: Regularly check all wiring connections for signs of wear, corrosion, or looseness. Ensure all wires are securely fastened and insulated.
- Physical Damage: Inspect the projection units for any physical damage, such as cracks or impacts, which could affect their functionality or water resistance.
6. Troubleshooting
If you encounter issues with your Angel Wing Carpet Projection Light, refer to the following troubleshooting steps:
- Lights Not Turning On:
- Check the power connection to ensure it is securely attached to a 12V power source.
- Verify that the chosen power source activates under the desired conditions (e.g., door open, unlock).
- Inspect the wiring for any breaks, pinches, or loose connections.
- Ensure the controllers are properly connected to both the power source and the lamp heads.
- Dim or Faint Projection:
- Clean the lens of the projection units. Dirt or debris can significantly reduce brightness.
- Ensure the vehicle's battery voltage is stable and sufficient (12V).
- Check for any obstructions between the projection unit and the ground.
- Flickering Lights:
- Check all electrical connections for looseness or intermittent contact.
- Ensure the wiring is not damaged or frayed.
- Distorted or Incomplete Pattern:
- Ensure the projection unit is securely mounted and not vibrating.
- Verify the lens is clean and free from scratches or damage.
- Check if the unit is installed at the correct angle and height for optimal projection.
If problems persist after following these steps, it is recommended to consult a professional automotive electrician.
7. Specifications
| Feature | Specification |
|---|---|
| Brand Name | KALADA |
| Model Name | LED Light Angel Wing Carpet Projection Light |
| Item Type | Atmosphere lamp |
| Voltage | 12 V |
| Product Power | 5.2W |
| Product Lumen | 450-500LM |
| Item Weight | 0.32 kg |
| Emitting Color | 4300K White Yellow |
| Applicable Vehicles | 99% of vehicle models are universal |
| Product Feature | Strong light transmittance |
| Certification | CE |
| Origin | Mainland China |
8. Warranty and Support
This product is manufactured by Shenzhen Feiyaoda Optoelectronics Technology Co., Ltd. and is CE certified, indicating compliance with European safety, health, and environmental protection requirements.
For specific warranty terms and conditions, please refer to the documentation provided by your seller at the time of purchase. Any claims or support requests should be directed to your point of purchase.
For regulatory compliance within the EU market, MJCM SARL acts as the authorized representative for this product. Further details regarding the EU Authorized Representative Agreement can be found in the official document: User manual (PDF).
9. User Tips
No specific user tips were available from reviews or Q&A for this product. However, general tips for car accessory installation include:
- Always double-check wiring polarity before making final connections to avoid damage to the product or vehicle electronics.
- Ensure all connections are waterproofed, especially for exterior components, to prevent moisture ingress and corrosion.
- Consider the angle and height of installation carefully to achieve the most visually appealing and effective projection pattern.