THINKCAR Thinkscan Plus S5

Contents

THINKCAR Thinkscan Plus S5 OBD2 Scanner User Manual

Model: Thinkscan Plus S5

Introduction

The THINKCAR Thinkscan Plus S5 is a powerful OBD2 diagnostic scan tool designed for DIY car owners and professional technicians. It provides comprehensive system diagnostics for ABS, SRS, ECM, and TCM systems, along with full OBDII functions and various maintenance and reset services. This manual will guide you through the setup, operation, and maintenance of your device.

Video: Unboxing and overview of the Thinkscan Plus S5, demonstrating its features and ease of use.

Safety Precautions and Warnings

To prevent personal injury or damage to vehicles and/or this tool, please read this user's manual carefully and observe the following safety precautions at a minimum whenever working on a vehicle:

  • Always perform automotive testing in a safe environment.
  • Do not attempt to operate or observe the tool while driving a vehicle. Operating or observing the tool will cause driver distraction and could cause a fatal accident.
  • Wear safety eye protection that meets ANSI standards.
  • Keep clothing, hair, hands, tools, test equipment, etc. away from all moving or hot engine parts.
  • Operate the vehicle in a well-ventilated work area: Exhaust gases are poisonous.
  • Put blocks in front of the drive wheels and never leave the vehicle unattended while running tests.
  • Use extreme caution when working around the ignition coil, distributor cap, ignition wires and spark plugs. These components create hazardous voltages when the engine is running.
  • Put the transmission in P (for A/T) or N (for M/T) and make sure the parking brake is engaged.
  • Keep a fire extinguisher suitable for gasoline/chemical/electrical fires nearby.
  • Don't connect or disconnect any test equipment while the ignition is on or the engine is running.
  • Keep this tool dry, clean, free from oil/water or grease. Use a mild detergent on a clean cloth to clean the outside of the tool when necessary.
  • Please use the DC 5V power adaptor to charge this tool. No responsibility can be assumed for any damage or loss caused as a result of using power adaptors other than the provided one.

Setup

1.1 Initial Use

The following settings should be made when you initially use the tool.

1.1.1 Turn on the Machine

After connecting with the car, images will be shown on the screen as follows.

Thinkscan Plus S5 startup screen

Image: The initial startup screen of the Thinkscan Plus S5 device.

1.1.2 Language Setting

Select the tool language from the languages displayed on the interface.

Thinkscan Plus S5 language selection screen

Image: Language selection interface showing various language options including English, French, German, Italian, and Spanish.

1.1.3 Connect Wi-Fi

The system will automatically search all available Wi-Fi networks and you can choose the Wi-Fi needed. If the chosen network is open, you can connect it directly; If the chosen network is encrypted, you must enter the correct password. Then you can connect Wi-Fi after clicking "connect".

Tips: Wi-Fi must be set. If no Wi-Fi network is available nearby, you can enable "Portable Mobile Hotspot" on your phone.

Thinkscan Plus S5 Wi-Fi network settings screen

Image: Wi-Fi network settings interface displaying available networks and connection status.

1.1.4 Choose Time Zone

Choose the time zone of the current location, then the system will automatically configure the time according to the time zone you chose.

Thinkscan Plus S5 timezone selection screen

Image: Timezone selection interface showing a list of timezones.

1.1.5 User Agreement

Please read all the terms and conditions of the user agreement carefully. Choose "Agree all the above terms", and click the "Agree" button to complete the registration process. Then the page will jump to the "Congratulations on your successful registration" interface.

Thinkscan Plus S5 user agreement screen

Image: User agreement screen with options to agree to terms.

Operating Instructions

2.1 Choose the diagnostic function

The main interface of the Thinkscan Plus S5 provides various functions. Select the desired diagnostic function from the menu.

Thinkscan Plus S5 diagnostic function menu

Image: Main menu of the Thinkscan Plus S5 showing options like Scan, OBD, Maintenance & Service, ThinkFile, Update, Repair Info, and Settings.

A. Version Information

Click "Version Information" to read the current version information of the car ECU.

B. Read Fault Code

This function reads Diagnostic Trouble Codes (DTCs) from the ECU memory, helping to quickly identify the cause of vehicle breakdowns. When troubleshooting, DTCs are for reference only; parts should not be replaced solely based on DTC definitions. Always follow the car maintenance manual's procedures to confirm the root cause.

To read fault codes, click "Read Fault Code" from the diagnostic menu. The screen will then display diagnostic results.

Thinkscan Plus S5 fault code display

Image: Screen displaying fault codes (DTCs) such as P2187 and P0304, with options for diagnostic reports.

C. Clear Fault Code

This function clears DTCs from the ECU memory. Click "Clear Fault Code" to delete existing DTCs. A dialog box will confirm "DTC successfully cleared".

Note: For general vehicles, strictly follow this sequence: read DTC, clear it, perform a test run, read DTC again for verification, repair the vehicle, clear DTC, and re-verify that DTCs no longer appear.

D. Read Data Stream

This function reads and displays real-time data and parameters from the car ECU. Observing these data streams helps maintenance technicians understand the vehicle's overall performance and suggest maintenance.

Screen buttons:

  • Select all: Tick the box next to a data stream to select it. Click this button to select all data streams.
  • Deselect: Click this button to deselect all checked data streams.
  • OK: Confirm current operations. After selection, the system will display dynamic data.
  • (Graph): Displays data streams in dynamic wave patterns.
  • Report: Saves the current data streams.

If "1 / X" appears, it means not all data stream options are displayed. Swipe the screen to see more. Three display modes are available:

  • Figure: Displays parameters with wave patterns.
  • Value: Default display mode shows parameters with numbers and lists. (Note: If a data stream value is outside the standard range, it will be displayed in red.)
  • Combine: Graphs are presented together for comparisons. (Note: Different data flow options are marked in different colors.)
Thinkscan Plus S5 data stream display

Image: Screen showing live data stream values and graphical representation of engine RPM.

Maintenance & Reset Functions

The Thinkscan Plus S5 offers 28 commonly used maintenance and reset functions. These include:

  • Maintenance light reset
  • Steering angle reset
  • Battery matching
  • ABS exhaust
  • Throttle matching
  • Brake pad reset
  • DPF regeneration
  • Anti-theft matching
  • Nozzle coding
  • Tire pressure reset
  • Suspension level calibration
  • Headlight matching
  • Gearbox matching
  • Sunroof initialization
  • EGR Adaption
  • Gear Learning
  • ODO Reset
  • Airbag Reset
  • Transport Mode
  • A/F Reset
  • Stop/Start Reset
  • NOx Sensor Reset
  • AdBlue Reset (Diesel Engine Exhaust Gas Filter)
  • Seat Calibration
  • Coolant Bleeding
  • Tyre Reset
  • Windows Calibration
  • Language Change

2.2.1 Maintenance Light Reset

Resets the mileage or driving time to zero after maintenance, turning off the maintenance light and starting a new maintenance cycle.

2.2.2 Steering Angle Reset

Calibrates the steering angle sensor. Required after replacing the sensor, mechanical steering parts, four-wheel positioning, or body repair.

2.2.3 Battery Matching

Resets the car battery's monitoring unit. Necessary when replacing the main battery or when the battery monitoring sensor needs re-matching to ensure accurate power detection and prevent false alarms.

2.2.4 ABS Exhaust

Bleeds air from the ABS system to restore braking sensitivity. Essential when replacing ABS components like the computer, pump, master cylinder, brake cylinder, brake line, or brake fluid.

2.2.5 Throttle Matching

Initializes the throttle actuator to return the ECU's learning value to its initial state, allowing for accurate control of throttle movement and intake volume. Needed after replacing the ECU, power loss to the ECU, replacing the throttle assembly, disassembling the intake port, or when idle control characteristics change.

2.2.6 Brake Pad Reset

Resets the brake pad system after replacement or when the brake pad indicator light is on. Also required after repairing the brake pad sensor circuit or replacing the servo motor.2.2.7 DPF Regeneration

Initiates the regeneration process for the Diesel Particulate Filter (DPF) to remove particulate matter. Required after replacing the exhaust back pressure sensor, disassembling/replacing the particle trap, removing/replacing fuel additive nozzles or catalytic oxidizer, or when the DPF regeneration fault lamp is lit.

2.2.8 Anti-theft Matching

Enables the car's immobilizer control system to identify and authorize remote control keys. Necessary when replacing the ignition key, ignition switch, instrument cluster, engine control unit (ECU), body control module (BCM), or remote control battery.

2.2.9 Nozzle Coding

Writes or rewrites the actual code of the fuel injection nozzle in the ECU to control or correct fuel injection amount more accurately. Required after replacing the ECU and the fuel injector.

2.2.10 Tire Pressure Reset

Resets the tire pressure monitoring system (TPMS) and turns off the fault indicator. Necessary if tire pressure is too low, leaks, or after replacing TPMS equipment or tires.

2.2.11 Suspension Level Calibration

Adjusts the vehicle body height. Required when replacing the vehicle height sensor or control module in the air suspension system, or if the vehicle level is incorrect.

2.2.12 Headlight Matching

Initializes the adaptive headlight system to adjust lighting angle based on ambient light, driving speed, and body posture.

2.2.13 Gearbox Matching

Completes self-learning of the gearbox to improve shift quality. Required after gearbox disassembly or repair to compensate for driving conditions and prevent shifting delays or car impact.

2.2.14 Sunroof Initialization

Sets sunroof functions such as lock-off, rain-closing, memory for sliding/tilting, and outside temperature threshold.

2.2.15 EGR Adaption

Used to learn the EGR (Exhaust Gas Recirculation) valve after it is cleaned or replaced.

2.2.16 Gear Learning

The crankshaft position sensor learns crankshaft tooth machining tolerance and saves it to the computer for more accurate engine misfire diagnosis. If tooth learning is not performed for a car equipped with a Delphi engine, the MIL turns on after the engine is started, and DTC P1336 'tooth not learned' is detected. This function is crucial after replacing the engine ECU, crankshaft position sensor, or crankshaft flywheel.

2.2.17 ODO Reset

Copies, writes, or rewrites the odometer's kilometer value in the chip using a car diagnostic computer and data cable to display the actual mileage. Necessary if mileage is incorrect due to a damaged vehicle speed sensor or odometer failure.

2.2.18 Airbag Reset

Resets airbag data to clear the airbag collision fault indicator. After a collision and airbag deployment, this function can recover airbag computer data, clear fault codes, and turn off the airbag light, allowing the airbag computer to be reused.

2.2.19 Transport Mode

Deactivates transport mode to restore normal vehicle functions, which may include limiting vehicle speed, disabling door opening network, and remote control key functions.

2.2.20 A/F Reset

Sets or learns Air/Fuel ratio parameters.

2.2.21 Stop/Start Reset

Enables or disables the automatic start-stop function via setting the hidden function in the ECU (if supported by the vehicle and hardware).

2.2.22 NOx Sensor Reset

Resets the catalytic converter learned value stored in the engine ECU if the NOx fault is re-initialized and the NOx catalytic converter is replaced.

2.2.23 AdBlue Reset (Diesel Engine Exhaust Gas Filter)

Required after the diesel exhaust treatment fluid (car urea) is replaced or filled up.

2.2.24 Seat Calibration

Matches seats with memory function that have been replaced or repaired.

2.2.25 Coolant Bleeding

Activates the electronic water pump before venting the cooling system.

2.2.26 Tyre Reset

Sets the size parameters of modified or replaced tires.

2.2.27 Windows Calibration

Performs door window matching to recover ECU initial memory and restore automatic ascending and descending functions of power windows.

2.2.28 Language Change

Changes the system language of the vehicle's central control panel.

2.3 ThinkFile

This module records and establishes files for diagnosed vehicles. Files are created based on the vehicle VIN and check time, including all diagnostic-related data such as diagnostic reports, data stream records, and screenshots.

Thinkscan Plus S5 ThinkFile screen

Image: ThinkFile interface showing saved diagnostic records.

2.4 Repair Info

This section includes four items to assist technicians:

  • Fault code database: Explanations of fault codes.
  • Vehicle compatibility table: Lists all diagnosable vehicles.
  • Videos: Equipment usage guides, maintenance, and diagnosis guides.
  • Learning course: Demonstrates tool operation.

These functions help technicians quickly grasp equipment use and improve diagnostic efficiency.

2.5 Software Update

This module allows you to update the diagnostic software and app, and manage frequently used software. If new software updates are available, you can download them to keep your device synchronized with the latest version.

Thinkscan Plus S5 software update screen

Image: Software update interface showing upgradable and upgraded software, with options to update.

2.6 Settings

The device uses system settings. After initial setup, users can modify or add related information, or swipe the screen from the top to access settings.

Thinkscan Plus S5 settings screen

Image: Settings menu showing options for Feedback, Customer Management, and Business Information.

2.6.1 Account Information

Users need to register information including email, points, orders, and homepage. Points can be earned by participating in THINKCAR events or recommending products, with each point deducting 1 USD from purchases.

2.6.2 Customer Management

Displays information for all clients whose vehicles have been diagnosed.

2.6.3 Business Information

Allows adding repair shop information, which will be displayed to the owner in the diagnostic report.

2.6.4 Network

Configures connectable Wi-Fi networks.

2.6.5 Firmware Upgrade

Used to update the device's firmware.

Troubleshooting (Q&A)

Q: Why does it have no responses when connected to a car computer?

A: Please confirm:

  1. Whether the diagnostic dongle is correctly connected.
  2. Whether the ignition switch is ON.
  3. If all checks are normal, send vehicle year, make, model, and VIN number to customer support using the Feedback feature.

Q: Why does the system stop while reading the data stream?

A: This may be caused by loose diagnostic dongles. Please unplug the dongle and reconnect it firmly.

Q: Communication error with vehicle ECU?

A: Please confirm:

  1. Whether the diagnostic dongle is correctly connected.
  2. Whether the ignition switch is ON.
  3. If all checks are normal, send vehicle year, make, model, and VIN number to customer support using the Feedback feature.

Q: Why does the host screen flash when the engine ignition starts?

A: It is normal and caused by electromagnetic interference.

Q: How to upgrade the system software?

A:

  1. Start the tool and ensure a stable Internet connection.
  2. Go to "Set up" -> "App Update", click "OTA" and then click "check version" to enter the system upgrade interface.
  3. Complete the process by following the instructions on the screen step by step. It may take a few minutes depending on the internet speed. Please be patient. After successfully completing the upgrade, the tool will automatically restart and enter the main interface.

Specifications

FeatureDescription
Brand NameTHINKCAR
Model Namethinkscan plus S5 obd2 scanner
Item TypeEngine Analyzer
ElectronicYes
MaterialABS
Voltage3.7V
Special FeaturesWifi
Hardware Version2024 new obd2 code reader
Software Version2024 new automotive tools
External Testing CertificationCE
CertificationRoHS, FCC, CE
OriginMainland China
Item Weight0.76 kg
Item Height20 cm
Item Width10 cm
Item Length30 cm
Display5-inch TouchScreen
System DiagnosisABS, SRS, ECM, TCM
OBDII FunctionsRead Codes, Clear Codes, Live Data, EVAP Test, Freeze Frame, I/M Readiness, O2 Sensor Test, On-Board Monitor Test, Vehicle Information, DTC Lookup
Supported LanguagesTurkish, English, French, Spanish, German, Polish, Russian, Italian, Portuguese, Japanese

User Tips

  • Ease of Use: Many users find the Thinkscan Plus S5 very easy to operate, making it suitable for both beginners and experienced users.
  • Check Packaging: Upon receiving your device, carefully inspect the packaging and contents to ensure all parts are present and undamaged.
  • Vehicle Compatibility: Before purchasing or using, verify that the device is compatible with your specific vehicle make, model, and year, especially for specialized functions like EGR reset or for brands like VAG, BRP, or Can-Am.
  • Advanced Functions: Be aware that some advanced reset functions may require additional purchases or subscriptions. Check the device's software for details on specific features.

Warranty & Support

Warranty Terms

This warranty applies only to users and distributors who purchase THINKCAR TECH INC products through normal procedures. Within one year from the date of delivery, THINKCAR TECH warrants its electronic products for damages caused by defects in materials or workmanship. Damages to the equipment or components because of abuse, unauthorized modification, use for non-designed purposes, operation in a manner not specified in the instructions, etc. are not covered by this warranty. The compensation for dashboard damage caused by the defect of this equipment is limited to repair or replacement.

THINKCAR TECH does not bear any indirect and incidental losses. THINKCAR TECH will judge the nature of the equipment damage according to its prescribed inspection methods. No agents, employees or business representatives of THINKCAR TECH are authorized to make any confirmation, notice or promise related to THINKCAR TECH products.

Customer Service

Product tutorials, videos, FAQ, and coverage lists are available on the Thinkcar official website.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.