HORACO ZX-SWTGW2224AS

Contents

HORACO 24 Port 2.5GbE Managed Switch User Manual

Model: ZX-SWTGW2224AS

1. Introduction

This manual provides detailed instructions for the installation, configuration, and operation of your HORACO 24 Port 2.5GbE Managed Switch (Model: ZX-SWTGW2224AS). This smart web-managed switch is designed for home labs, small to medium businesses, and advanced network setups, offering features like Link Aggregation (LACP), Quality of Service (QoS), VLAN segmentation, and DHCP snooping. Please read this manual thoroughly before using the device to ensure proper setup and optimal performance.

HORACO 26 Port 2.5G Web Managed Switch
Figure 1.1: HORACO 24 Port 2.5GbE Managed Switch

2. Safety Information

  • Ensure the power supply voltage matches the device's requirements (AC 100-240V, 50/60Hz).
  • Do not open the device casing; refer all servicing to qualified personnel.
  • Keep the device away from water, fire, and high humidity environments.
  • Install the device in a well-ventilated area to prevent overheating.
  • Use only the provided power adapter.

3. Package Contents

Upon unpacking, please verify that all items are present and in good condition:

  • HORACO 24 Port 2.5GbE Managed Switch (Model: ZX-SWTGW2224AS)
  • Power Adapter (12V 4A)
  • User Manual (this document)
  • Rack Mount Kit (if applicable to your model variant)

4. Specifications

FeatureDescription
Switch TypeEthernet
Number of Interfaces24*2.5G RJ45 Port, 2*10G SFP+ Port
VLAN SupportYES
CertificationCE, FCC, RoHS
Transmission Rate2000 Mbps
Switch Capacity160Gbps
Communication ModeFull-Duplex & Half-Duplex
FunctionVLAN Support, QoS, LACP
Packet forwarding rate119.04Mpps
MAC Address Table Size16K
Package cache12Mbit
Industry standardEMS: EN61000-4-2 (ESD), EN61000-4-5 (Surge)
Network Medium100Base-TX : Cat5 or above UTP/STP(≤100m); 1000Base-TX : Cat5 or above UTP/STP(≤100m); 2.5GBase-T: Cat5e or above UTP/STP(≤100m); 5GBase-T: Cat6 or above UTP/STP(≤100m); 10000Base-TX : Cat7 or above UTP/STP(≤100m)
Working environmentWorking Temperature: -10-50°C; Storage Temperature: -40-70°C; Working Humidity: 10%-90%, non-condensing; Storage Temperature: 5%-95%, non-condensing;
Power voltageAC 100-240V, 50/60Hz
Power supply12V 4A
Chip SchemeRTL9302D+ RTL8224
Power consumption≤36W

5. Setup

5.1 Physical Installation

The HORACO switch is designed for 1U rack mounting, making it suitable for integration into standard server racks. Ensure adequate space for ventilation around the device.

1U Rack Mount Installation Example
Figure 5.1: Example of 1U Rack Mount Installation

5.2 Initial Connection

  1. Connect the provided power adapter to the switch and a power outlet.
  2. Connect your computer directly to any RJ45 port on the switch using an Ethernet cable.
  3. Ensure your computer's IP address is in the same network segment as the switch but different from the switch's default IP. For example, set your PC's IP address to 192.168.2.x (where 1 < x ≤ 254) and the subnet mask to 255.255.255.0.

5.3 Web Interface Login

The switch features a smart web-managed interface for easy configuration.

  1. Open a web browser (superior to IE 9.0, Chrome 23.0, or Firefox 20.0 recommended).
  2. Type the default switch address http://192.168.2.1 into the address bar and press "Enter".
  3. A login window will appear. Enter the default username "admin" and password "admin".
  4. Click "Log in" to access the switch system.
Web Network Management Interface Screenshots
Figure 5.2: Web Network Management Interface Login and Dashboard

6. Operation and Configuration (Web Interface)

The web interface provides comprehensive control over the switch's functions. The typical operation interface includes a navigation bar on the left and the main content area on the right.

6.1 Navigation Bar Overview

The navigation bar on the left side of the web interface provides access to various management functions. Key menu items include Status, Network, Port, VLAN, MAC Address Table, Spanning Tree, ERPS, Multicast, Security, QoS, Diagnostics, and Management. Each main item contains submenus for specific configurations.

Menu ItemDescription
StatusView system information, port states, and MAC address table.
NetworkConfigure IP address and DNS settings.
PortManage port settings, link aggregation (LAG), EEE, Jumbo Frames, port security, protected ports, storm control, and mirroring.
VLANCreate and configure VLANs, manage VLAN membership and port settings.
MAC Address TableConfigure static and filtering MAC addresses.
Spanning TreeConfigure STP/RSTP/MSTP properties and port settings to prevent network loops.
ERPSConfigure Ethernet Ring Protection Switching properties and instances for high reliability.
MulticastManage general multicast properties, group addresses, router ports, and IGMP snooping.
SecurityConfigure management access (HTTP/SNMP), DHCP snooping, and IMPV binding.
QoSConfigure Quality of Service settings including queue scheduling, CoS/DSCP mapping, and rate limits.
DiagnosticsPerform network diagnostics such as Ping and Copper Test.
ManagementManage user accounts, firmware upgrades, configuration backup/restore, and SNMP settings.

6.2 Key Configuration Areas

6.2.1 Port Settings

The switch features 24x 2.5G RJ45 ports and 2x 10G SFP+ optical ports. These ports support compatible 1G, 2.5G, and 10G modules (not included).

Product Overview: 24x 2.5G RJ45 Ports, 2x 10G SFP+ Ports
Figure 6.1: Front Panel Port Overview

Navigate to Port > Port Setting to configure individual port parameters such as speed, duplex mode, and flow control. You can enable or disable auto-negotiation for interface rates (100 Mbit/s, 1,000 Mbit/s, 2500 Mbit/s, 5000 Mbit/s, and 10 Gbit/s).

Link Aggregation (LAG) bundles multiple physical interfaces into a single logical interface to increase bandwidth and reliability. The switch supports LACP (Link Aggregation Control Protocol) based on IEEE 802.3ad Standard.

LACP Link Aggregation Diagram
Figure 6.2: LACP Link Aggregation Example

To configure, go to Port > Link Aggregation > Group. You can select a load-balancing algorithm and add member ports to a LAG. For dynamic aggregation, select LACP mode and configure system priority, port priority, and timeout methods under Port > Link Aggregation > LACP.

6.2.3 VLAN Configuration

VLANs (Virtual Local Area Networks) segment a physical LAN into logical LANs, improving network security and efficiency by limiting broadcast domains. The switch supports 802.1Q VLAN mode.

VLAN Segmentation Diagram
Figure 6.3: VLAN Segmentation Preventing Network Storms

To create a new VLAN, navigate to VLAN > VLAN > Create VLAN. You can then configure VLAN membership and port settings under VLAN > VLAN > VLAN Configuration or VLAN > VLAN > Membership.

6.2.4 Spanning Tree Protocol (STP)

STP (including RSTP and MSTP) prevents network loops in redundant link setups, ensuring network stability. Access these settings via Spanning Tree > Property to configure global parameters and Spanning Tree > Port Setting for individual port attributions.

6.2.5 Quality of Service (QoS)

QoS allows prioritizing network traffic to ensure performance for critical applications. The switch supports various QoS features including queue scheduling, CoS/DSCP mapping, and rate limiting.

Configure global QoS properties under QoS > General > Property. Adjust queue scheduling, CoS/DSCP mapping, and rate limits for ingress/egress ports in their respective submenus under the QoS section.

6.2.6 Security Features

The switch offers security features like DHCP Snooping and IMPV Binding to prevent unauthorized devices from accessing the network and ensure proper IP address assignment.

Access DHCP Snooping settings via Security > DHCP Snooping > Property. IMPV Binding can be configured under Security > IP Source Guard > IMPV Binding.

7. Maintenance

7.1 Firmware Upgrade

Regularly updating the switch firmware ensures optimal performance, security, and access to new features. Navigate to Management > Firmware > Manual Upgrade to perform a firmware update. You can use TFTP or HTTP methods to upload the firmware file.

7.2 Configuration Management

It is crucial to save your configuration changes and back them up. Go to Management > Configuration > Save Configuration to save the running configuration to the startup configuration. You can also backup and restore configurations from this section.

7.3 System Reboot

To reboot the switch, click the "Reboot" option available on the upper right corner of the web interface. Be aware that unsaved changes will be lost upon reboot.

8. Troubleshooting

The web interface includes diagnostic tools to help identify and resolve network issues.

8.1 Ping

The Ping utility checks the availability of specified IP addresses or host names and measures network latency. Access it via Diagnostics > Ping. Enter the target IP address or hostname and the number of tests, then click "Ping".

8.2 Copper Test

The Copper Test evaluates the state of Ethernet cables connected to the RJ45 ports and can locate faults. Go to Diagnostics > Copper Test, select the port to test, and click "Copper Test" to view the results.

9. User Tips

  • This switch operates quietly, making it suitable for noise-sensitive environments like home labs or offices.
  • The web-based management interface is intuitive and powerful; take time to explore its features for advanced network control.
  • If you encounter setup difficulties, HORACO customer service has been noted for good responsiveness and helpful support.

10. Frequently Asked Questions (FAQ)

Q: How much power does the HORACO ZX-SWTGW2224AS switch consume?
A: The total power consumption of the switch is ≤36W.

11. Warranty and Support

For detailed warranty information and technical support, please refer to the official HORACO documentation or contact HORACO customer service. A comprehensive user manual in PDF format is also available for download: Download User Manual (PDF).

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.