1. Product Introduction
The COOSPO BK467 is a versatile sensor designed to measure either speed or cadence in real-time. It transmits this data wirelessly to compatible applications or bike computers via Bluetooth 4.0 and ANT+ protocols. This user manual provides detailed instructions to help you effectively use and maintain your BK467 sensor.
2. Standard Accessories
Please check the package contents to ensure all items are present:
- Speed / Cadence Sensor x 1
- Rubber Mat (Flat x 1, Curved x 1)
- Band (Large x 2, Medium x 2, Small x 2)
- User Manual x 1
Image: COOSPO BK467 package contents.
3. Setup and Installation
3.1. Remove the Insulation Sheet
- Twist the battery cover with a coin in the 'OPEN' direction.
- Open the battery cover and remove the battery.
- Carefully take out the insulating sheet located beneath the battery.
Image: Battery compartment showing the CR2032 battery and the 'Please remove before use' tab.
3.2. Mode Switching (Speed or Cadence)
The BK467 sensor operates in either Speed Mode or Cadence Mode. You can switch between modes by rebooting the sensor:
- Twist the battery cover with a coin in the 'OPEN' direction.
- Open the battery cover and remove the battery.
- Reinstall the battery.
- Twist the battery cover in the 'CLOSE' direction to secure it.
After reinstalling the battery, observe the indicator light:
- A RED indicator flash signifies Speed Mode.
- A BLUE indicator flash signifies Cadence Mode.
Image: Visual guide for switching sensor modes.
3.3. Installation for Speed Mode
For speed measurement, install the sensor on the wheel axle:
- Buckle the curved rubber mat onto the back of the sensor.
- Bind the sensor with a large rubber band onto the wheel axle.
Image: Sensor installed on a wheel hub for speed tracking.
3.4. Installation for Cadence Mode
For cadence measurement, install the sensor on the pedal crank:
- Buckle the flat rubber mat onto the back of the sensor.
- Bind the sensor with a small rubber band onto the pedal crank.
Image: Sensor installed on a crank arm for cadence tracking.
Image: Easy installation examples for both modes.
4. Operating the Sensor
Once installed and the correct mode is selected, the BK467 sensor will automatically begin transmitting data when motion is detected. It is compatible with a wide range of devices and applications:
4.1. Compatible Devices and Apps
The BK467 supports both ANT+ and Bluetooth 4.0, allowing connection to various bike computers and smartphone applications:
- ANT+ Compatible Devices: COOSPO, GARMIN, Wahoo, IGPSPORT, ZWIFT, ONELAP, BKOOL, TACX, BRYTON.
- Bluetooth Compatible Apps: CoospoRide, STRAVA, NIKE+, ENDOMONDO, RUNTASTIC PRO, WAHOO FITNESS, or other apps with speed/cadence features.
Image: Compatibility with various ANT+ devices and Bluetooth apps.
Image: Example of data display in the CoospoRide app.
5. Specifications
| Feature | Specification |
|---|---|
| Weight | 9.5 g |
| Battery Life | 300 hours |
| Battery Type | CR2032 220mAh |
| Waterproof | IP67 |
| Wireless | Bluetooth & ANT+ |
| Size | 41 x 34 x 10 mm |
| Max Speed | 120 km/h |
| Max Cadence | 300 rpm |
| Working Temperature | -10°C ~ 50°C |
| Color | Black |
5.1. Applicable Smart Phones
- iOS 7.0 or above, iPhone 4s model or above
- Android 4.3 or above with Bluetooth 4.0
6. Maintenance
6.1. Battery Replacement
The sensor uses a CR2032 3V coin battery. To replace the battery, follow the steps for 'Remove the Insulation Sheet' (Section 3.1) to open the battery cover, replace the old battery with a new CR2032 battery, and then securely close the cover. Remember to check the LED flash color to confirm the desired mode (red for speed, blue for cadence) after battery replacement.
User Tip: Some users find it helpful to write the date of battery installation on the battery itself to track its lifespan.
6.2. Waterproofing
The COOSPO BK467 sensor is IP67 waterproof, meaning it is protected from dust and can withstand immersion in water up to 1 meter for 30 minutes. This makes it suitable for use in various weather conditions, including rain. However, it is not designed for prolonged underwater use.
Image: IP67 Waterproof rating illustration.
6.3. Cleaning
Wipe the sensor with a soft, damp cloth. Do not use abrasive cleaners or solvents.
7. Troubleshooting
- Sensor not connecting/pairing:
- Ensure the battery is correctly installed and the insulation sheet has been removed.
- Verify the sensor is in the correct mode (red flash for speed, blue for cadence) for your intended use.
- Make sure Bluetooth is enabled on your smartphone or bike computer.
- If using a bike computer, ensure other Bluetooth devices (like your phone) are not actively trying to connect to the sensor, as this can interfere with ANT+ pairing.
- Move the sensor closer to the receiving device.
- Reboot the sensor by removing and reinserting the battery.
- Inaccurate readings:
- Check that the sensor is securely mounted and not moving during your ride.
- Ensure the correct mode (speed or cadence) is selected for the sensor's mounting location.
- For speed sensors, ensure your bike computer's wheel circumference setting is accurate.
- Sensor lights not flashing during use:
- The sensor's indicator lights are primarily for mode selection upon battery installation. They typically do not flash continuously during normal operation to conserve battery life. This is normal behavior.
8. User Tips
- Initial Setup: Always remove the plastic protector from the battery before first use.
- Mode Confirmation: Pay close attention to the LED color (red for speed, blue for cadence) when reinstalling the battery to ensure the sensor is in your desired mode.
- Pairing: If you experience issues pairing with a bike computer, try temporarily turning off Bluetooth on your smartphone to avoid interference.
- Battery Life: To help track battery life, consider writing the installation date on the CR2032 battery.
- Responsiveness: Many users find the BK467 to be very responsive and quick to sync compared to other brands.
9. Safety and Compliance Information
9.1. Battery Statement and Warning
WARNING: INGESTION HAZARD
- This product contains a button cell or coin battery.
- DEATH or serious injury can occur if ingested.
- A swallowed button cell or coin battery can cause Internal Chemical Burns in as little as 2 hours.
- KEEP new and used batteries OUT OF REACH of CHILDREN.
- Seek immediate medical attention if a battery is suspected to be swallowed or inserted inside any part of the body.
- Remove and immediately recycle or dispose of used batteries according to local regulations and keep away from children. Do NOT dispose of batteries in household trash or incinerate.
- Even used batteries may cause severe injury or death. Call a local poison control center for treatment information.
- Compatible battery type: CR2032. Nominal battery voltage: 3V.
- Do not force discharge, recharge, disassemble, heat above 45°C or incinerate. Doing so may result in injury due to venting, leakage or explosion resulting in chemical burns.
- Ensure the batteries are installed correctly according to polarity (+ and -).
- Do not mix old and new batteries, different brands or types of batteries, such as alkaline, carbon-zinc, or rechargeable batteries.
- Remove and immediately recycle or dispose of batteries from equipment not used for an extended period of time according to local regulations.
- Always completely secure the battery compartment. If the battery compartment does not close securely, stop using the product, remove the batteries, and keep them away from children.
9.2. FCC Statement
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
9.3. Waste Disposal
Waste electrical products should not be disposed of with household waste. Please recycle where facilities exist. Contact your local government or a retailer for additional information.
Symbol: Crossed-out wheeled bin indicates separate collection for electrical and electronic equipment.
9.4. General Safety Guidelines
- Do not open or modify the product.
- Do not disassemble or attempt to service this product.
- This product is safe under normal and reasonably foreseeable operating conditions.
- If the product is operating improperly, contact COOSPO support.
- The product must be returned to the manufacturer for any service or repair.
10. Warranty and Support
10.1. Disclaimer
The information contained in this manual is for reference only. The product described above may be subject to alteration due to the manufacturer's continuing research and development plans, without prior announcement. COOSPO shall not make any statement or warranty about this manual.
10.2. Additional Resources
For a digital copy of this user manual or additional support, please refer to the official COOSPO website or scan the QR code provided on the first page of the printed manual.
A PDF version of the user manual is available at: COOSPO BK467 User Manual (PDF)