1. Introduction
Thank you for choosing the KPSUN 10mm Mini LED Downlight. This compact, IP65-rated 12V spotlight is designed for versatile ambient lighting in both indoor and outdoor environments. Its small size and durable construction make it ideal for illuminating ceilings, stairs, walkways, courtyards, cabinets, and corridors. Please read this manual thoroughly before installation and use to ensure proper function and safety.

Figure 1: KPSUN 10mm Mini LED Downlights
2. Safety Information
WARNING:
- This is a 12V lamp. Use only with a constant voltage power supply.
- Do not reverse the power supply input and output polarity. Incorrect wiring can damage the device and pose a safety hazard.
- Ensure all electrical connections are made by a qualified professional and comply with local electrical codes.
- Disconnect power before installation, maintenance, or troubleshooting.
- Do not attempt to modify the light fitting.
3. Package Contents
Your package should contain the following:
- KPSUN 10mm Mini LED Downlight(s) (quantity as per your order, e.g., 5, 8, 10, 12, 15, 18, or 20 pieces)
Note: The DC12V constant drive power (driver) is NOT included and must be purchased separately if needed.
4. Specifications
| Feature | Specification |
|---|---|
| Brand Name | KPSUN |
| Model Number | 0.5W Spot Light |
| Power | 0.5W |
| Input Voltage | DC12V |
| Voltage | 12 V |
| Power Source | DC |
| Luminous Flux | 60-249 lm |
| Power Tolerance | 3% |
| Material | Aluminum |
| Main Material | Aluminum |
| Protection Class | IP65 Indoor |
| Is Dimmable | No |
| Application | Foyer (suitable for various ambient lighting) |
| Color Temperature Options | Warm White (2700-3000K), Nature White (4000-4500K), Cold White (6000-6500K) |
| Working Temperature | -25°C ~ +45°C |
| Certification | RoHS, CE |
| High-concerned chemical | None |
| Origin | Mainland China |
Beam Angle Options: 30° (narrow beam) and 120° (wide beam) are available, influencing light spread.

Figure 2: Beam Angle Comparison (30D vs 120D)
5. Installation Instructions
Before beginning installation, ensure the power supply is disconnected.
5.1 Component Overview

Figure 3: Downlight Components
5.2 Dimensions
The downlight requires a 10mm cutout for installation. Refer to the diagram below for detailed dimensions based on the beam angle.

Figure 4: Downlight Dimensions (30° and 120° Beam Angle)
5.3 Wiring Diagram (DC12V)
The downlight uses high-temperature silicone copper core wire. Connect the lights in parallel to a DC12V constant drive power supply. Ensure correct polarity: Red wire to DC12V+ and Black wire to DC12V-.

Figure 5: Reference Installation Diagram (DC12V)
5.4 Installation Steps
- Provide Mounting Holes: Create mounting holes that match the product dimensions (10mm cutout diameter).
- Connect Wiring: Connect the red wire of the lamp to the positive (+) terminal of your DC12V power supply and the black wire to the negative (-) terminal. Ensure all connections are secure.
- Press Stainless Steel Spring: Gently press the stainless steel springs on the sides of the light fitting inwards.
- Embed Light Fitting: Push the light fitting into the prepared hole until the springs secure it in place.
6. Operating Instructions
Once installed and wired correctly, simply connect the DC12V power supply to activate the downlights. There are no additional controls on the lights themselves. Operation is controlled via the power supply switch.
7. Maintenance
- Cleaning: To clean the downlight, ensure the power is off. Wipe gently with a soft, dry cloth. Do not use abrasive cleaners or solvents.
- IP65 Rating: The IP65 rating indicates the light is protected against dust ingress and low-pressure water jets from any direction. While suitable for damp locations and some outdoor use, avoid submerging the light in water.
- Inspection: Periodically inspect the wiring and connections for any signs of wear or damage.
8. Troubleshooting
- Light does not turn on:
- Check if the power supply is connected and switched on.
- Verify all wiring connections are secure and correctly polarized (Red to +, Black to -).
- Ensure the power supply is providing 12V DC.
- Check for any loose connections or damaged wires.
- Light flickers:
- Ensure the power supply is stable and providing constant voltage.
- Check for loose wiring connections.
If you experience persistent issues, please contact customer support.
9. User Tips
- For optimal light distribution, consider the beam angle (30° for focused light, 120° for wider coverage) when planning your installation.
- When installing multiple lights, ensure your DC12V power supply has sufficient wattage capacity for the total number of lights.
- The compact size makes these lights excellent for accent lighting in display cases or under cabinets.
10. Warranty & Support
This KPSUN Mini LED Downlight comes with a 2-year warranty for free replacement due to manufacturing defects. Please retain your proof of purchase for warranty claims.
For further assistance, technical support, or warranty inquiries, please contact the seller or refer to the official product documentation. A detailed user manual in PDF format may be available for download from the seller's website or by contacting customer support.
Additional Resources: A user manual (PDF) is available for this product. You may find it by searching for the product model on the seller's website or by contacting customer support.