Quansheng UV-K6

Contents

Quansheng UV-K6 Walkie Talkie User Manual

Model: UV-K6

1. Safety Information & Warnings

1.1. FCC Compliance Statements

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

  • Reorient or relocate the receiving antenna.
  • Increase the separation between the equipment and receiver.
  • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
  • Consult the dealer or an experienced radio/TV technician for help.

This device complies with FCC radiation exposure limits set forth for an uncontrolled environment. Do not use this device when the antenna shows obvious damages. Hold this transmitter approximately 25 mm away from your face and speak normal with the antenna pointed up and away. Use the supplied belt clip for body-worn configuration as other accessories may not comply to the limits.

WARNING: MODIFICATION OF THIS DEVICE TO RECEIVE CELLULAR RADIOTELEPHONE SERVICE SIGNALS IS PROHIBITED UNDER FCC RULES AND FEDERAL LAW.

1.2. CE Warning

Use the two-way radio in environments with temperatures between 0-40°C; otherwise, it may damage your two-way radio. It can be operated under 2000m.

Hereby, we declare that the radio equipment type two-way radio is in compliance with Directive 2014/53/EU.

1.3. Precautions Before Using

  • Please put the radio and accessories where children cannot reach.
  • Maintenance can only be performed by professional technicians.
  • Please use the standard battery pack and charger in order not to destroy the radio.
  • Please use the standard antenna, in order not to shorten the communication distance.
  • Do not expose the radio to sunlight for a long period of time, nor put it near heat.
  • Do not put it in extreme dust or wet environments.
  • Do not clean the radio with fierce chemical products, cleaning agents or strong washing agents.
  • Do not transmit when the antenna is not installed.
  • If you find a bad smell or smoke, please turn off the radio immediately. And take the battery off the radio, then contact with the agent.

2. Package Contents

Carefully unpack the portable radio. We suggest that you check the following items before you discard the packaging materials.

2.1. Standard Accessories

ItemQuantity
Portable Radio1
Antenna1
Li-ion Battery1
Battery Charger1
Belt Clip1
User's Manual1

2.2. Accessories Photo

Quansheng UV-K6 accessories including radio, antenna, charger base, wrist strap, battery, and user manual.
Included accessories: Radio, Antenna, Charger Base, Wrist Strap, Battery, and User Manual.

3. Product Overview

3.1. Radio Diagram

Quansheng UV-K6 Walkie Talkie held in hand, showing its compact size and display.
Quansheng UV-K6 Walkie Talkie in hand.
Quansheng UV-K6 Walkie Talkie with key features highlighted: High Quality Sound, Multi Frequency Band, Type-C Charge, AM/FM Reception.
Quansheng UV-K6 with highlighted features.
Quansheng UV-K6 showing its Multi Segment Transceiver Double Display feature.
Multi Segment Transceiver Double Display.
Icons representing key features of the Quansheng UV-K6: AM/FM, NOAA Weather Alarm, Frequency Meter Function, Frequency Measurement, Type-C Charger, Scrambling Function, Emergency Alarm, Frog Call Ending Sound, Complete Machine Replication, Cross Section Talking.
Key features of the Quansheng UV-K6.

3.2. LCD Display Symbols

The LCD displays various symbols to indicate the radio's status and functions. Refer to the table below for their meanings:

SymbolDescription
Signal Strength (Yll)Indicates signal strength. Fewer grids mean weaker signal.
Transmitting Output Power (HML)Indicates current transmitting power: H (High), M (Medium), L (Low).
CTCSS/DCS (CT DCS)CT appears for CTCSS code, DCS for DCS code.
Voice Prompt (D)Voice prompt is on.
Narrow Band Mode (N)Radio operates in narrow band mode.
VOX Function (VOX)Voice Operated Transmit function is active. Transmission starts when sound pressure reaches set value.
Frequency Deviation (+-)+ means transmitting frequency equals receiving frequency plus deviation; - means transmitting frequency equals receiving frequency minus deviation.
DTMF Decoding (DTMF)DTMF signal decoding is on.
Dual Watch (DW)Frequency dual watch is on. Displays two frequency bands.
Keypad Lock (Lock icon)Keypad is locked.
Battery Level (Battery icon)Displays current battery level. Flashing icon indicates low battery.
Main Channel (Main channel indicator)Indicates the main channel. All operations apply to this channel.
Voice Encryption (SCR)Voice encryption is active for this channel.
Reverse Mode (R)Receive and transmit frequencies are reversed.
Scanning (◆◆)Indicates participation in scan list 1 or 2.
Cross-Band (WX)Cross-Band Receiving/Transmitting.
Receiving (RX)Currently receiving.
Transmitting (TX)Currently transmitting.
Type-C Charging (USB-C icon)Indicates Type-C charging is active.
AM Receiving (AM)AM receiving mode.
NOAA Auto Scan (NS)NOAA channel automatic scan.

3.3. Buttons and Controls

3.3.1. PTT Key (Transmitting Button)

  • Press and hold the PTT key to transmit and speak into the microphone.
  • Release the PTT key to receive.

3.3.2. Programmable Side Keys

The radio features two programmable side keys. Their default functions are:

  • Side Key 1: Short press for Monitor function. Long press for 1750Hz tone.
  • Side Key 2: Short press for Jacklight (flashlight). Long press for Emergency Alarm.

These functions can be customized using programming software:

FunctionDescription
Emergency Mode On/OffActivates Emergency Alarm as per software settings.
High/Low Output Power SelectionSwitches between High/Low output power.
MonitorTurns Monitor function on/off. Ignores CTCSS/DCS and monitors the actual channel.
FM RadioTurns FM Radio Mode on/off.
Scan On/OffTurns Scan function on/off.
VOX On/OffTurns VOX function on/off.
Transmitting 1750Turns on 1750 continuous transmitting.
JacklightTurns Jacklight on/off.

3.3.3. Keypad Buttons

  • MENU/Confirm Key: Short press to enter menu, select item, and confirm. Long press to enter last setting. In DTMF, it means 'A' code word.
  • EXIT/Clear Key: Short press to exit current menu. Long press to return to main page. Clears input info. In DTMF, it means 'D' code word.
  • Up/Down Keys: Navigate menus. In DTMF, Up is 'B' code word, Down is 'C' code word.
  • * Key: Short press to enter manual dial/call page. Long press to start frequency or channel scanning. In DTMF, it means '*' code word.
  • F Key: Function key. Used with 0-9 and * for quick function switching. Long press to lock/unlock keypad. In DTMF, it means '#' code word.

4. Setup

4.1. Battery Charging

Battery packs are not charged when shipped. Charge them before use.

  • Initial Charging: The first few charges may not bring the battery to its full capacity. Full capacity is reached after two or three charge/discharge cycles.
  • Charging Process: Power off the radio before charging. Do not use the radio during charging.
  • After Full Charge: Remove the battery pack from the charger-base. Do not charge it again until it is completely run down to avoid memory effect.
  • Battery Life: If battery life does not improve after proper charging, it indicates the battery is nearing its end of life and should be replaced.
  • Recommended Chargers: Always use original factory battery packs and chargers.

4.1.1. Type-C Charging

The Type-C charging port is for emergency charging only. For normal charging, use the charger-base.

  • When charging via Type-C while the radio is on, a charging symbol will appear in the upper right corner of the screen.
  • Charging continues even if the radio is powered off.
  • A blue light indicates charging. It blinks when nearly full, then switches to trickle charge. The blue light turns off when charging is complete.
  • Do not remove the battery when charging via Type-C.

4.2. Power On/Off & Volume Control

Turn the "Power/Volume Switch" clockwise to power on the radio. Turn counter-clockwise until a "click" sound is heard to power off. Rotate clockwise to increase volume, counter-clockwise to decrease.

4.3. Power On Password Protection

If a power-on password is set via programming software, the screen will display "LOCK" upon startup. Input the password to use the radio normally.

5. Operation

5.1. Menu Navigation

Press the MENU key to enter the menu. Use the Up/Down keys to select menu items. Press MENU again to confirm selection. Press EXIT to return to the previous menu or long press EXIT to return to the main page.

5.1.1. Menu Item Descriptions

No.Item NameFunction DescriptionValue Range
1SQLSquelch Level0-9
2STEPStep Frequency0-5
3TXPOutput Power (LOW/MID/HIGH)0-2
4R_DCSReceive DCS (OFF, 1-104: DCS, 105-208: reverse DCS)0-208
5R_CTCSReceive CTCSS (OFF, 1-50: CTCSS)0-50
6T_DCSTransmit DCS (OFF, 1-104: DCS, 105-208: reverse DCS)0-208
7T_CTCSTransmit CTCSS (OFF, 1-50: CTCSS)0-50
8SFT-DFrequency Deviation Setting0-2
9OFFSETFrequency of Frequency Deviation (0-999.9999M)
10W/NChannel Bandwidth (0:WIDE, 1:NARROW)0-1
11SCREncrypted Communication (0-10 types of scrambling frequency)0-10
12BCLBusy Channel Lock (OFF,ON)0-1
13MEM-CHChannel Save
14SAVEBattery Save (OFF/1:1/1:2/1:3/1:4)0-4
15VOXVOX Setting (OFF: turn off VOX, 1-10: 1 to 10 grade)0-10
16ABRAuto Backlight (OFF: turn off, 1-5: turn off in 1-5 seconds)0-5
17TDRDual-watch On/Off (OFF: Close, CHAN_A/B: Default TX Channel)0-2
18WXCross-Band Receiving/Transmitting (OFF: Close, CHAN_A/B: TX Channel)0-2
19BEEPBEEP Control (OFF, ON)0-1
20TOTTime-Out-Timer (1-10min)1-10
21VOICEVoice Prompt (OFF, CHI: Chinese, ENG: English)0-2
22SC-REVScan Resume Mode (TO: Resume scan after 5s; CO: Resume scan after signal disappear; SE: After receive signal, stop scan)0-2
23MDFChannel Display Mode (FREQ: Display frequency, CH: Display channel No., NAME: Display channel name)0-2
24AUTOLKAuto Keypad Lock (OFF,ON)0-1
25S-ADD1Participate in scan list 1 (OFF: not participating, ON: participation)0-1
26S-ADD2Participate in scan list 2 (OFF: not participating, ON: participation)0-1
27STETail Tone Elimination (OFF,ON)0-1
28RP-STERepeater Tail Tone Elimination (OFF,ON)0-1
29MICMIC Sensitivity (0-4 level)0-4
301-CALLOne Key Call Channel
31S-LISTChannel Scan List Select (LIST1: Scan list 1, LIST2: Scan list 2)1-2
32SLIST1Channel Scan List 1 Configuration
33SLIST2Channel Scan List 2 Configuration
34AL-MODAlarm Mode (SITE: local alarm, TONE: Distant + local alarm)0-1
35ANI-IDANI-ID, DTMF communication radio ID
36UPCODEDTMF UP CODE
37DWCODEDTMF DOWN CODE
38D-STDTMF Side Tone Switch (OFF, ON)0-1
39D-RSPDTMF Decoding Response (NULL: Close, Ring: Local ringing, REPLY: reply response, BOTH: local ringing + reply response)0-3
40D-HOLDDTMF Auto Reset Time (5s-60s)5-60
41D-PREDTMF pre-load time (30-990ms)3-99
42PTT-IDDTMF PTT-ID TX Mode (OFF: Close, BOT: Press PTT to send UP CODE, EOT: Release PTT to send DOWN CODE, BOTH: Press or release PTT to send.)0-3
43D-DCDDTMF decoding enable signal (OFF,ON)0-1
44D-LISTDTMF Contact List1-16
45PONMSGDisplays of Power On (FULL: full screen display, MSG: Welcome info, VOL: Voltage)0-2
46ROGERReminding of End Talk (OFF: no reminding, ROGER: with reminding, MDC: Frog Sound Tail Tone)0-2
47VOLBattery Voltage0-1
48AMAM Channel Mode On/Off (Used only for 108-136MHz)0-1
49NOAA_SNOAA Channel Auto Scan On/Off
50DEL_CHChannel Delete
51RESETReset (VFO: Reset parameter beside channel parameter; ALL: Reset all parameter.)0-1

5.2. Switching Main Channel

Press F+2 to switch the main channel. The solid arrow on the LCD indicates the main channel. Press PTT to transmit on the main channel.

5.3. Dual Band Single-Watch/Dual-Watch

Set dual-watch operation mode via MENU → 17 (TDR). Select CHAN_A or CHAN_B for the default TX channel. The screen will show "DW".

5.4. Frequency/Channel Mode Switch

On the main page, press F+3 to switch between Frequency Mode and Channel Mode.

  • Frequency Mode: Manually input RX frequency or adjust with Up/Down keys. TX frequency cannot be directly input but can be changed by adjusting Offset Frequency and its direction.
  • Channel Mode: Displays current channel number. Manually input channel number or switch with Up/Down keys.

5.5. Cross-Band Receiving/Transmitting

Set via MENU → 18 (WX). When CHAN_A or CHAN_B receives a valid call, that channel automatically becomes the main channel until the call ends. The "WX" character will be displayed.

5.6. Channel Save

  • MR Mode: Copy current channel to a new channel.
  • VFO Mode: Set RX Frequency, Frequency Deviation Direction, Wide/Narrow Bandwidth, RX/TX CTCSS/DCS, TX Output Power, Scanning participation, DTMF code, Scrambler, etc. Then press MENU → 13 (MEM-CH) → CH-001, press MENU again, select channel with Up/Down keys or number keys, press MENU. If "SURE?" appears, press MENU again to save.

5.7. Channel Delete

Press MENU → 50 (DEL_CH), then press MENU again. Select the channel to delete with Up/Down keys or number keys. If "SURE?" appears, press MENU again to delete.

5.8. Receiving/Transmitting CTCSS/DCS Setting

CTCSS/DCS are used to eliminate unwanted noise signals during reception.

  • RX DCS: MENU → 4 (R_DCS), select desired RX DCS code.
  • RX CTCSS: MENU → 5 (R_CTCS), select desired RX CTCSS code.
  • TX DCS: MENU → 6 (T_DCS), select desired TX DCS code.
  • TX CTCSS: MENU → 7 (T_CTCS), select desired TX CTCSS code.

5.9. Fast Copy One Channel / Frequency Meter

This function acts as a frequency meter for two-way radios and other devices. It requires a strong signal and antennas on both transmitter and receiver, with close proximity.

  • Press F+4 to enter Frequency Meter interface.
  • When a strong signal is received, the LCD displays carrier frequency and transmitting channel (CTCSS or DCS).
  • Press * key to re-measure frequency.
  • After measurement, press MENU to save the frequency and CTCSS/DCS to a specified channel.
  • Press EXIT or PTT to exit Frequency Meter during measurement.
  • Set correct receiving frequency, then press F+* to start searching.
  • When a valid CTCSS/DCS signal is received, it will display the searched TX CTCSS/DCS signal. Press MENU to save it to the current channel.
  • "SCAN CMP" indicates a valid signal was found and search stopped. "SCAN FAIL" indicates no valid signal was found.

5.11. DTMF Functions

5.11.1. DTMF Calling

  • Manual Dialing: Press PTT and use number keys to dial.
  • Automatic Calling: Press *, enter 3 digits, then short press PTT. The radio automatically sends its own ID.
  • Single Call: Send other party's ID + your ID (e.g., 123*100).
  • Group Call: Use a group calling code (e.g., #12# for IDs 120-129, #1## for IDs 100-199).
  • All Call: Send ### to call all users.

5.11.2. DTMF Receiving

Set MENU → 43 (D-DCD) to ON. When a personal DTMF ID code is received, decoding is successful, and the caller's name is displayed. Communication is possible during the reset time.

Set MENU → 40 (D-HOLD) for automatic reset time (default 5 seconds).

Set MENU → 39 (D-RSP) for automatic response after DTMF call (NULL: off, RING: local ring, REPLY: automatic callback, BOTH: local ring + automatic callback).

5.11.3. PTTID

Configure DTMF online and offline codes via programming software. When enabled, the radio sends the online code when PTT is pressed and the offline code when PTT is released.

5.12. Scanning

5.12.1. Activating Scan

  • Method 1: Long press * key to start or exit scanning.
  • Method 2: Set a side key as Scan Start/Close Switch.

5.12.2. Frequency Scanning

During scanning, change scan direction with Up/Down keys. Press PTT or EXIT, or long press * to exit.

5.12.3. Channel Scanning

Scans channels in the scan list. You can answer incoming calls by pressing PTT.

  • Select Scan List: MENU → 31 (S-LIST), choose LIST1 or LIST2.
  • View Channels in List: MENU → 32 (SLIST1) or MENU → 33 (SLIST2).
  • Add Current Channel to List: MENU → 25 (S-ADD1) or MENU → 26 (S-ADD2).
  • Select Scanning Mode: MENU → 22 (SC-REV).

5.12.4. Priority Scanning

You can specify a priority scanning channel. During scanning, 50% of the scan time is on priority 1 members. If priority 2 members are present, priority 1 scan time is reduced to 25%. The radio continues to scan for transmission activity on priority 1 members, even if on a non-priority channel. If activity is detected, it stops current transmission and calls the priority 1 member.

5.13. Emergency Alarm

Used for emergency situations. Can be initiated anytime, on any screen, or even during channel activity. The emergency alarm button must be configured via programming software.

  • Press the emergency alarm key to activate local audible/light alarm and remote alarm.
  • Exit alarm mode by pressing any key.
  • Alarm Tone: MENU → 34 (AL-MOD) → TONE (local alarm sound, remote signal).
  • Alarm Site: MENU → 34 (AL-MOD) → SITE (local alarm sound only).

5.14. FM Radio

Press F+0 to enter FM radio mode.

  • Use Up/Down keys or keypad to change frequency or select pre-stored FM channels.
  • Press F+1 to switch between VFO and MR mode.
  • Press F+2 to start automatic FM channel search (stores up to 20 channels).
  • Press F+3 to start manual FM channel search (users save channels manually).
  • If the radio receives a call or PTT is pressed, it temporarily exits FM mode for communication, then returns.
  • Press EXIT or F+0 to exit FM mode.

5.15. Emergency Weather Channel Receiving (NOAA)

Quansheng UV-K6 displaying NOAA Weather Forecast on its screen, in an outdoor setting.
NOAA Weather Forecast feature.
  • Press F+5 to enter or exit NOAA Weather Alert.
  • The radio can receive 10 NOAA channels.
  • This mode can be set via MENU → 49 (NOAA_S).

5.16. Keypad Locking

Long press the # key to lock or unlock all keypad keys. Side keys remain functional when keypad is locked.

5.17. Reset

Process: MENU → 51 (RESET)

  • VFO: Reserves all storage channels.
  • ALL: Resets all parameters, including storage channels.
  • After reset, the radio will restart, and all menu settings will return to factory defaults.

5.18. One Key Call Channel

  • Press F+9 to immediately jump to the one key call channel.
  • Set an important channel as the one key call channel via MENU → 30 (1-CALL).

5.19. Aviation Band Receiving

  • Enter the receiving frequency. If the local aviation frequency is unknown, use the scan function to scan the 108-136MHz band.
  • Set MENU → 48 (AM) to ON for AM modulation (aviation intercom) or OFF for FM modulation.
  • Menu 48 settings are only valid for the 108-136MHz frequency band.

5.20. Wireless Radio Replication

Product demonstration video showing various features including wireless radio replication.

  • Hold PTT + Side Key 2 to enter Wireless Radio Replication interface. The LCD will display "Air Copy (RDY)".
  • Both transmitting and receiving radios must have consistent frequencies for replication, set via the digital keypad. Default frequency is 410.0125MHz.
  • Press EXIT on the receiving radio to enter receiving mode.
  • Press MENU on the transmitting radio to start frequency data transmission.
  • During copying, the LCD displays progress (RCV:XX E:XX, E:XX indicates errors). After completion, the transmitter displays "SND: 120".

6. Specifications

Table of detailed specifications for the Quansheng UV-K6, including channels, frequency stability, size, weight, voltage, temperature, resistance, transmit power, transmit current, and sensitivity.
Detailed Specifications Table.

6.1. General Specifications

  • Channels: 200
  • Stored FM Radio Channel Quantity: 20
  • NOAA Channels: 10
  • Frequency Stability: ±1ppm
  • Modulation Mode: FM: 11KΦF3E (12.5KHz), 16KΦF3E (25KHz)
  • Dimensions: 115mm x 60mm x 37.5mm
  • Weight: 234g
  • Operating Temperature: -20°C to +60°C
  • Antenna Impedance: 50Ω

6.2. Transmitting Specifications

ParameterFCC VersionCE/UKCA VersionNORMAL VersionIC Version
FrequencyUHF420-450MHz, VHF144-148MHzUHF430-440MHz, VHF144-146MHzUHF400-470MHz, UHF350-400MHz, VHF136-174MHzUHF430-450MHz, VHF144-148MHz
Output Power≤5W
Emission Current≤1.5A
Max Frequency Deviation≤5KHz (25KHz), ≤2.5KHz (12.5KHz)
Modulation Distortion≤5%
Stray Power≤7.5uW
Adjacent Channel Power70dB (25KHz), 60dB (12.5KHz)
Residual Modulation40dB

6.3. Receiving Specifications

ParameterValue
Sensitivity (FM 12dB SINAD)F1 (50-76): -121dBm
F2 (108-135.9975): -121dBm
F3 (136-173.9975): -123dBm
F4 (174-349.9975): -123dBm
F5 (350-399.9975): -123dBm
F6 (400-469.9975): -123dBm
F7 (470-599.9975): -121dBm
WFM (20dB SINAD)WFM (76-108): -110dBm
AM (10dB S/N)F2 (108-135.9975): -113dBm
Audio Frequency≥0.5W
Audio Distortion≤10%

Note: All stated specifications are subject to change without notice or obligation due to technical improvements.

7. Maintenance

  • Do not attempt to disassemble the radio; repairs should only be performed by qualified technicians.
  • Use only the original battery and charger provided by the manufacturer.
  • Avoid exposing the radio to direct sunlight for extended periods or placing it near heat sources.
  • Do not place the radio in dusty or humid environments.
  • Clean the radio with a soft, damp cloth. Do not use harsh chemicals, cleaning agents, or strong detergents.
  • If the radio emits strange odors or smoke, immediately turn it off, remove the battery, and contact customer support.

8. Troubleshooting

  • Crackle/Background Noise: Adjust the squelch level (SQL menu item) to reduce unwanted background noise during reception.
  • Difficulty with Firmware Updates: Some newer versions (e.g., bootloader 7.00.07) of the UV-K6 (or UV-K5(8) variants) may not be compatible with custom firmwares or programming software like Chirp. Always back up your current firmware before attempting any updates.
  • Limited Band Coverage (e.g., 11 meters): The radio may not support certain bands like 11 meters or have a spectrum analyzer function by default. Check specifications and user tips for potential modifications or limitations.
  • Aviation Receiving Performance: If aviation band reception is moderate, ensure proper antenna connection and try scanning the 108-136MHz band.
  • Programming Issues: If programming via port is difficult, consider using recommended software like Chirp for easier configuration.

9. User Tips

  • Firmware: While the radio works well out of the box, some users explore firmware modifications for advanced features. Be aware that newer bootloader versions (e.g., 7.00.07) might prevent custom firmware flashing or programming with tools like Chirp. Always back up your current firmware before attempting any changes.
  • Programming: For easier programming, especially for amateurs, software like Chirp is highly recommended.
  • Reception Quality: If you experience crackling or excessive background noise, adjust the Squelch Level (SQL) in the menu settings.
  • SSB Filter: The radio does not come with an SSB filter board by default, but it may be possible to purchase and install one yourself for enhanced performance on certain bands.
  • Battery Security: The battery attachment might feel slightly simple; ensure it is securely fastened.

10. Warranty & Support

The accuracy and completeness of the contents are sought in the process of compilation, but we do not bear any responsibility for possible errors or omissions. With the continuous development of technology, we reserve the right to change the design and specifications of the product without notice. No copy, modification, translation, and dissemination of this handbook may be made in any form without the prior written authorization of our department.

For further assistance or inquiries, please contact your local dealer or the manufacturer's customer support.

User Manual cover with FCC, CE, UKCA, IC, RoHS logos.
Compliance and Certification Logos.

A PDF version of this user manual is available for download. You can view it here.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.