PowMr POW-M80-PRO

Contents

PowMr 80A MPPT Solar Charge Controller

Model: POW-M80-PRO

User Manual

1. Introduction

Welcome to the PowMr POW-M80-PRO MPPT Solar Charge Controller, a cutting-edge solution for your solar energy system. Designed for outstanding performance and reliability, this controller features advanced CNC technology, an intuitive LCD screen, and user-friendly buttons for real-time monitoring of operational data and system status. It supports Maximum Power Point Tracking (MPPT) battery charging mode to maximize energy utilization efficiency.

The POW-M80-PRO is compatible with 12V, 24V, 36V, and 48V battery systems and various battery types, including flooded lead-acid, gel-sealed lead-acid, and lithium batteries. It automatically controls battery charging and discharging processes to optimize battery life and enhance overall system performance. Equipped with self-diagnostic and electronic protection functions, it ensures system reliability and stability.

2. Important Safety Instructions

WARNING: Carefully read and adhere to all safety instructions before installation and operation.

  • Read the user manual thoroughly before installing and operating the controller.
  • Installation and operation should only be performed by individuals with proper training and supervision.
  • This controller has no user-serviceable components; do not attempt to disassemble or repair it yourself.
  • Install the controller in a well-ventilated environment with adequate clearance around it.
  • Mount the controller on non-combustible walls, ensuring no flammable materials are nearby. It is normal for the controller to generate heat during operation.
  • Place the controller in an environment protected from direct sunlight, rain, humidity, and dust. Keep it away from flammable liquids or gases. This controller is for indoor use only.
  • Do not install or operate the controller directly above or in an enclosed space above batteries, as batteries emit explosive gases.
  • Do not place any objects on top of the controller.

Battery Installation and Charging Safety

  • Install and charge batteries in well-ventilated or exhaust-ventilated environments.
  • Ensure there are no open flames near batteries, as they emit explosive gases.
  • Battery acid is corrosive; if contact occurs, rinse immediately with clean water.
  • Do not charge non-rechargeable batteries.
  • Do not charge lithium batteries when the temperature is below 0°C. Charging frozen batteries is prohibited.

3. Product Features

  • MPPT 80A Max Charging Current: Efficiently charges your battery bank.
  • Versatile Battery Voltage: Automatically detects 12V, 24V, 36V, and 48V systems.
  • High PV Input Voltage: Supports a maximum PV open-circuit voltage of 160VDC.
  • Parallel Function: Supports up to 12 units in parallel for increased charging capacity and PV input.
  • High Efficiency: Features 99.9% tracking efficiency and up to 97% peak conversion efficiency.
  • Multi-Stage Charging Algorithm: Optimizes each charging cycle for various battery types (flooded, gel, lithium).
  • Adaptive Boost Charging: Monitors battery response to determine optimal boost stage duration.
  • External Temperature Probe: Enhances precision in battery temperature monitoring for optimal system performance.
  • Forced Air Cooling: Built-in cooling fan for efficient heat dissipation.
  • Lithium Battery Activation: Activates protected lithium batteries using solar panel energy.
  • Multi-Protection Functions: Includes photovoltaic input overcurrent, photovoltaic array short circuit, reversed photovoltaic polarity, overvoltage protection for batteries, overdischarge protection for batteries, and over-temperature protection.
PowMr MPPT Solar Controller Features

Figure 1: Key features of the PowMr MPPT Solar Charge Controller, highlighting 80A max current, 12/24/36/48V auto voltage, 160VDC max PV input, and up to 12 units parallel function.

Battery Compatibility and Efficiency

Figure 2: The controller supports various battery types (SLA, GSL, FLB, LiFePO4, Lithium-Ion, User-defined) and boasts 99% high tracking efficiency and 97% peak conversion efficiency.

4. Product Appearance and Components

Controller LCD and Ports

Figure 3: Detailed view of the MPPT Solar Charge Controller's LCD display screen and connection ports.

Components Overview:

  1. LCD Display Screen
  2. Function Keys (PV/SET, BAT/▲, BAT/▼)
  3. Photovoltaic Input Interface
  4. Battery Interface
  5. Temperature Probe Port
  6. Parallel Communication Port
  7. Port Cover Plate
  8. Heat Dissipation Vent

LCD Display Screen Indicators:

  • Day/Night Indicator
  • Battery Capacity
  • Charging in Progress
  • PV Parameter (Voltage, Power, Operating Mode)
  • Battery Parameter (Voltage, Current, Temperature, Type)

5. Setup and Installation

5.1 Unpacking

Carefully open the packaging and inspect for any signs of damage. Verify that all components are present:

  • 1x PowMr MPPT Solar Charge Controller
  • 1x Set of screws and accessories
  • 1x Parallel communication terminal
  • 1x User Manual
  • 1x Installation guide card
  • 1x Temperature probe

Video 1: This video demonstrates the unboxing of the PowMr MPPT Solar Charge Controller, showing all included components: the controller unit, screws, parallel communication terminal, user manual, installation guide card, and temperature probe.

5.2 Choosing the Installation Location

  • Install in a space with good natural ventilation/exhaust.
  • Avoid direct sunlight.
  • Ensure at least 75mm clearance around the top, bottom, and sides of the controller.
  • Mount on a non-combustible wall.
  • For multiple controllers in parallel, install at the same horizontal height with a minimum 200mm spacing.

5.3 Wiring Precautions

  • All installation and wiring must be performed by a certified electrician.
  • Always connect the battery first, then the PV input (Battery > PV Input).
  • Ensure correct polarity (+ to + and - to -) to avoid short-circuits and damage.
  • Tighten all cable connections to minimize resistance and prevent overheating. Use appropriate cable sizes for the current rating.

5.4 Wiring Guidelines

  1. Mounting: Install the controller vertically with its ports facing downward. Secure it to the wall using the four mounting holes.
  2. Battery Wiring: Connect the battery to the controller using appropriate cables. Ensure all circuit breakers are in the OFF position before wiring. Connect the positive cable to the positive terminal and the negative cable to the negative terminal.
  3. PV Wiring: Connect the photovoltaic array to the controller using appropriate cables.
  4. Temperature Probe Connection: Connect the temperature probe wire to the controller and securely fix the probe end to the battery using insulation tape.
  5. Pre-Startup Check: After all connections are made and securely tightened, close the circuit breakers in the order of Battery and then PV Input circuitry.
Solar Connect Diagram

Figure 4: Wiring diagram showing the connection of the MPPT Solar Charge Controller to a solar array, battery, load, and inverter. Max PV Array Open-Circuit Voltage 160V.

5.5 Parallel Operation

The PowMr MPPT Solar Charge Controller supports parallel operation for increased charging capacity and PV input. Up to 12 units can be connected in parallel.

  • Controller Placement: Parallel controllers should be installed at the same horizontal level with a minimum spacing of 200mm between units.
  • Solar Array Connection: Each controller must be connected to a separate solar array. One solar array cannot be connected to more than one controller.
  • Battery Bank Connection: All parallel controllers must be connected to the same battery bank.
  • Communication: Connect the parallel communication cables between units.
Parallel Operation Schematic

Figure 5: Schematic diagram illustrating how to connect multiple PowMr MPPT Solar Charge Controllers in parallel. Each controller connects to a separate solar array and all controllers share a common battery bank via parallel communication cables and power cables.

6. Operating Instructions

6.1 Operation Interface Overview

The LCD display provides real-time information about your solar system. Use the function keys to navigate through different parameters.

6.2 Button Functions

  • PV/SET Button: Short press to switch photovoltaic input parameters. Long press to confirm settings.
  • BAT/▲ Button: Short press to switch battery parameters (move to next item). Long press to enter battery parameter settings. In setup mode, increases value or returns to previous item.
  • BAT/▼ Button: Short press to switch battery parameters (return to previous item). In setup mode, decreases value or returns to previous item.
  • Long Press Both BAT Buttons: Restores factory settings.

6.3 Photovoltaic Parameters

The display cycles through PV Input Voltage, PV Input Power, and Operating Mode/Fault Codes. Operating modes include Night Mode, Fast Charging Mode (MPPT), Boost Charging Mode, and Float Charging Mode.

6.4 Battery Parameters

The display shows Current Battery Voltage, Charging Current, Device Temperature, Battery Type, Parallel Communication Code, Calibrated Battery Voltage, Boost Charging Voltage, Float Charging Voltage, and MPP Tracking Return Voltage. Parameters can be adjusted using the BAT/▲ and BAT/▼ buttons in setup mode.

7. Maintenance

To ensure optimal performance and longevity of your PowMr MPPT Solar Charge Controller, perform the following checks and maintenance at least twice a year:

  • Ensure the controller is securely mounted in a clean and dry environment.
  • Ensure proper airflow around the controller and clean any dust or debris from the heat sinks.
  • Inspect all exposed wires for insulation damage (e.g., sun exposure, friction, rodent damage). Repair or replace damaged wires.
  • Tighten all terminals and check for loose, broken, or burnt cable connections.
  • Confirm that all system components are properly grounded.
  • Ensure all terminals are free from corrosion, insulation damage, high temperatures, or signs of burning/discoloration.
  • Check for dirt, nesting insects, and corrosion. Clean promptly if present.

WARNING: Risk of electric shock! Always turn off all power sources before performing maintenance.

8. Troubleshooting

The controller displays fault codes to assist in diagnosing issues:

Fault CodePossible CausesSolutions
18Low input photovoltaic voltageIncrease the number of solar panels or connect them in series.
60Overtemperature protectionAllow the device to cool down to resume normal operation.
63High battery voltageMeasure battery voltage; if it exceeds rated voltage, close the PV array circuit breaker.
65Low battery voltageCharge the battery until voltage exceeds the undervoltage termination voltage.
71High input photovoltaic voltageReduce the number of connected PV arrays or modify series/parallel connection.
73Overcharging currentModify series/parallel connection to decrease voltage or current values.

9. Specifications

ParameterSpecification (POW-M80-PRO)
Solar Input Specification
Max. Solar Array Open-Circuit Voltage160V
Max Input Power (12V System)960W
Max Input Power (24V System)1920W
Max Input Power (36V System)2880W
Max Input Power (48V System)3840W
Battery Charging Specification
Charging TechnologyMPPT
Charging Algorithm3 Stages
Nominal Battery Voltage12V/24V/36V/48V
Battery Voltage Range9~60V
Rated Charging Current80A
Maximum Efficiency≤98%
MPPT Efficiency>99%
Temperature Compensation-3mV/°C/2V (default)
Self-Consumption44mA/12V; 26mA/24V; 18mA/36V; 12mA/48V
Environment Specification
Operating Temperature Range-35°C ~ +45°C
Humidity Range≤95%, Non-condensing
Altitude<3000m
General Specification
Protection LevelIP32
Dimensions260x180x75mm
Net Weight2kg
Product Dimensions

Figure 6: Dimensions of the PowMr MPPT Solar Charge Controller (POW-M80-PRO): 10.24in (height) x 7.09in (width) x 2.95in (depth).

10. User Tips

  • Cable Sizing: For optimal performance and safety, ensure proper cable sizing. This controller is designed to accommodate standard wiring gauges. If you are unsure about specific cable sizes like 4AWG, consult the wiring guidelines in the manual or a certified electrician to ensure compatibility and secure connections.
  • Battery Type Selection: Always ensure the correct battery type is selected in the controller settings to prevent overcharging or undercharging, which can damage your batteries.
  • Ventilation: Good ventilation is crucial for the longevity and efficient operation of your controller. Ensure it's installed in a location with adequate airflow.

11. Warranty and Support

Warranty Declaration

Our company reserves the right not to assume any quality warranty responsibilities under the following circumstances:

  • Damage caused by improper transportation, incorrect storage, installation, or usage.
  • Damage caused by non-professionals or untrained personnel.
  • Damage resulting from non-compliance with instructions and safety warnings in this document.
  • Damage caused by operation in unsuitable environments or beyond specified parameter ranges.
  • Damage resulting from unauthorized disassembly, product alteration, or software code modification.
  • Damage caused by abnormal natural conditions (force majeure).
  • Any damage resulting from failure to adhere to local standards and regulations during installation and operation.
  • Products outside the warranty period.

Contact Information

For technical support, warranty claims, or any inquiries regarding your PowMr product, please contact:

SHENZHEN HEHEJIN INDUSTRIAL CO.,LTD

Tel/Fax: +86 755-28219903

Email: support@powmr.com

Web: www.powmr.com

Address: Henggang Street, Longgang District, Shenzhen, Guangdong, China


Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.