Global F24-8D

Contents

F24-8D Industrial Wireless Radio Crane Remote Control User Manual

Model: F24-8D

1. Introduction

This manual provides essential information for the safe and effective use of your F24-8D Industrial Wireless Radio Crane Remote Control. Please read this manual thoroughly before installation and operation to ensure proper function and safety.

F24-8D Remote Control System Components

Figure 1: F24-8D Transmitter and Receiver Units

2. Safety Information

Always observe the following safety precautions:

  • Ensure all wiring is performed by qualified personnel.
  • Verify power supply voltage matches the receiver's specifications.
  • Do not operate the system if any part is damaged.
  • Always use the emergency stop function in critical situations.
  • Keep the transmitter dry and clean.

3. Setup

3.1 Package Contents

Verify that your package contains the following items:

  • 1 x F24-8D Transmitter (Handheld Remote)
  • 1 x F24-8D Receiver Unit
  • Accessories (e.g., wiring terminals, mounting hardware - may vary)
F24-8D Product Packaging

Figure 2: F24-8D Product Packaging

3.2 Receiver Mounting

Mount the receiver unit in a secure location near the equipment to be controlled. Ensure it is protected from excessive vibration, heat, and moisture. Use appropriate fasteners for secure installation.

3.3 Wiring the Receiver

The receiver unit requires electrical connection to the crane or hoist control circuit. Refer to the wiring diagram below for correct connections. Ensure power is disconnected before performing any wiring.

F24-8D Wiring Diagram

Figure 3: F24-8D Wiring Diagram (Transmitter and Receiver)

Wiring Diagram Details:

Pin No. (Transmitter)FunctionPin No. (Receiver)Function
(14)COM3X1 (1)Input X1
(15)SOUTH 1SX2 (2)Input X2
(16)NORTH 1SMAIN-IN (3)Main Power Input
(17)S/N 2SSTOP MAIN1Emergency Stop Output 1
(18)COM4STOP MAIN2Emergency Stop Output 2
(19)R0MAIN-OUT (4)Main Power Output
(20)COM5COM 1 (5)Common 1
(21)R1 1SUP 1S (6)Up (Single Speed)
(22)R2 1SUP 2S (7)Up (Double Speed)
(23)R1/R2 2SDOWN 1S (8)Down (Single Speed)
DOWN 2S (9)Down (Double Speed)
COM 2 (10)Common 2
EAST 1S (11)East (Single Speed)
WEST 1S (12)West (Single Speed)
E/W 2S (13)East/West (Double Speed)

Power Supply: The receiver is designed for AC380V (50-60Hz) operation, but supports various voltages as per model variant (AC/DC12-72V, AC36V AC48V, AC110V AC220V, AC380V). Ensure your power supply matches the specific receiver unit's voltage rating.

3.4 Transmitter Battery Installation

Open the battery compartment on the transmitter and insert the required batteries (typically AA or AAA, not specified in data, but common). Ensure correct polarity. Close the compartment securely.

4. Operating Instructions

4.1 Transmitter Overview

F24-8D Transmitter Front View

Figure 4: F24-8D Transmitter Front View

The transmitter features 8 control buttons, an emergency stop button, and a start button:

  • UP / DOWN: Controls vertical movement.
  • EAST / WEST: Controls horizontal movement along one axis.
  • SOUTH / NORTH: Controls horizontal movement along the other axis.
  • Buttons 1 / 2: Auxiliary functions (programmable or specific to equipment).
  • START: Initiates operation.
  • Emergency Stop (Red Mushroom Button): Immediately cuts power to controlled functions. Twist to release.
  • Power Key (Green Toggle): Turns the transmitter on/off.

4.2 Basic Operation

  1. Power On: Turn the green power key on the transmitter to the 'ON' position. The transmitter's indicator light should illuminate.
  2. Start System: Press the 'START' button on the transmitter. The receiver's indicator light should show activity.
  3. Control Movement: Press the directional buttons (UP, DOWN, EAST, WEST, SOUTH, NORTH) to control the crane/hoist.
  4. Double Speed Function: This model supports double speed. Typically, a light press activates single speed, and a harder press or a dedicated button (if configured) activates double speed for faster movement. Refer to your crane's specific configuration.
  5. Auxiliary Functions: Use buttons '1' and '2' for their assigned functions.
  6. Emergency Stop: In any emergency, press the red mushroom button firmly. This will immediately stop all controlled movements. To resume operation, twist the button clockwise to release it, then press 'START' again.
  7. Power Off: After use, turn the green power key on the transmitter to the 'OFF' position.

Video 1: Demonstration of F24-8D Transmitter and Receiver Operation

5. Maintenance

  • Cleaning: Keep the transmitter and receiver units clean and free from dust, dirt, and moisture. Use a soft, dry cloth for cleaning. Do not use abrasive cleaners or solvents.
  • Battery Replacement: Replace transmitter batteries when the indicator light dims or operation becomes intermittent. Always use fresh batteries of the specified type.
  • Inspection: Periodically inspect all cables, connections, and the housing of both units for any signs of wear, damage, or corrosion. Ensure all mounting screws are tight.
  • Environmental Conditions: Avoid exposing the units to extreme temperatures, direct sunlight for prolonged periods, or corrosive environments.

6. Troubleshooting

ProblemPossible CauseSolution
Transmitter not powering onDead batteries; Power key offReplace batteries; Turn power key to ON
Receiver not respondingNo power to receiver; Emergency stop engaged; Out of range; InterferenceCheck receiver power; Release emergency stop; Move closer to receiver; Check for sources of interference
Intermittent operationLow transmitter batteries; Loose wiring; InterferenceReplace batteries; Check all wiring connections; Reduce interference
Emergency stop not releasingButton jammedTwist button clockwise firmly to release. If still stuck, do not force; contact support.

7. Specifications

FeatureDetail
Model NumberF24-8D
MaterialABS
OriginMainland China
Control Type8 Buttons, Double Speed
Voltage OptionsAC/DC12-72V, AC36V AC48V, AC110V AC220V, AC380V
Package Length48 cm
Package Width25 cm
Package Height15 cm
Package Weight2.6 kg

8. User Tips

  • Wiring Clarity: Always double-check your wiring against the provided diagram. Incorrect wiring can damage the unit or the controlled equipment. If you are unsure, consult a qualified electrician.
  • Secure Mounting: Ensure the receiver is mounted securely to prevent accidental dislodgement or damage during operation.
  • Battery Management: Keep spare batteries for the transmitter on hand, especially for critical operations.
  • Line of Sight: While wireless, maintaining a clear line of sight between the transmitter and receiver can help ensure reliable communication, especially in environments with potential interference.

9. Warranty and Support

For warranty information, technical support, or service inquiries, please contact your original seller or distributor. Keep your purchase records for reference.

A detailed user manual in PDF format may be available for download: View User Manual (PDF)

© 2024 Global Industrial Remote Control Store. All rights reserved.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.