Quansheng UV-K5

Contents

Quansheng UV-K5 Walkie-Talkie User Manual

Model: UV-K5

1. Introduction

Thank you for purchasing the Quansheng UV-K5 walkie-talkie. This device is designed for reliable communication and incorporates advanced technology. Please read this manual thoroughly to understand its features, ensure safe operation, and fulfill warranty obligations.

This radio is set up to transmit a regulated signal on an assigned frequency. Altering or adjusting settings to exceed these limitations is against the law. All adjustments must be made by qualified technicians.

CE Warning: Use the two-way radio in environments with temperatures between 0-40°C. Operating outside this range may damage the radio. It can operate under 2000m altitude.

FCC Compliance Statements: This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.

FCC Radiation Exposure Limits: This device complies with FCC radiation exposure limits set forth for an uncontrolled environment. Do not use this device when the antenna shows obvious damages. Hold this transmitter approximately 25 mm away from your face and speak normally with the antenna pointed up and away. Use the supplied belt clip for body-worn configuration as other accessories may not comply with the limits.

WARNING: MODIFICATION OF THIS DEVICE TO RECEIVE CELLULAR RADIOTELEPHONE SERVICE SIGNALS IS PROHIBITED UNDER FCC RULES AND FEDERAL LAW.

Licensing Information: Use of this radio in the USA is subject to FCC rules & regulations. Changes or modifications not expressly approved by the manufacturer may void the user authority. To comply with FCC requirements, transmitter adjustments should be made only by or under the supervision of a technically qualified person. Replacement of any unauthorized transmitter component could violate FCC rules. Use of this radio outside the intended country may be prohibited by government regulations.

2. Setup

2.1. Unpacking and Accessories

Carefully unpack the portable radio and check the contents against the list below. If any items are missing or damaged, contact your dealer immediately.

ItemQuantity
Portable Radio1
Antenna1
Li-ion Battery1
Battery Charger1
Belt Clip1
User's Manual1

Accessories Photo:

Quansheng UV-K5 walkie-talkie with accessories including EU plug, battery, Type-C line, antenna, belt clip, hang, headset, and instructions.

Image: Quansheng UV-K5 walkie-talkie with its standard accessories, including an EU plug charger, battery, Type-C charging cable, antenna, belt clip, lanyard, headset, and the user manual.

2.2. Radio Diagram

Familiarize yourself with the layout and controls of your UV-K5 radio.

Quansheng UV-K5 walkie-talkie front view with labeled parts and features.

Image: Front view of the Quansheng UV-K5 walkie-talkie, highlighting key features such as NOAA, multi-segment, AM reception, quick matching, copy, cross-segment, power on, call the police, and voice encryption. It also shows the Type-C charging port and flashlight.

Multiple views of the Quansheng UV-K5 walkie-talkie from front, side, and back.

Image: Various views of the Quansheng UV-K5 walkie-talkie, showing its front panel, left side with PTT and side keys, right side with microphone/programming jacks, and rear panel.

2.3. LCD Display

The LCD screen displays various symbols to indicate the radio's status and selected functions. Refer to the table below for their meanings:

SymbolDescription
Signal Strength IndicatorIndicates signal strength. Fewer bars mean weaker signal.
HMLTransmitting Output Power Indicator (H: High, M: Medium, L: Low).
CT DCSCT indicates CTCSS code, DCS indicates DCS code.
DVoice prompt is on.
NRadio operates in narrow band mode.
VOXVOX Function is active. Transmission starts when sound pressure reaches set value.
+-+ indicates TX frequency = RX frequency + deviation; - indicates TX frequency = RX frequency - deviation.
DTMFDTMF signal decoding is on.
DWFrequency dual watch is on. Displays two frequency bands.
Keypad Lock IconKeypad is locked.
Battery IndicatorDisplays current battery level. Blinks when battery is low, prompting recharge.
Main Channel IndicatorIndicates main channel. PTT on secondary channel operates on main channel.
SCRVoice encryption for this channel is on.
RReverse mode. Receive and transmit frequency reverse.
◆◆Scanning. ◆ indicates participation in scan list 1, ◆◆ in scan list 2.
WXCross-Band Receiving/Transmitting.
RXReceiving.
TXTransmitting.
Type-C Charging MarkIndicates Type-C charging.
AMAM receiving mark.
NSNOAA channel automatic scan.
Close-up of the Quansheng UV-K5 screen displaying frequency 27.555500 and signal parameters.

Image: A close-up of the UV-K5 screen showing a frequency of 27.555500, signal strength, and other parameters like LNA, PGA, and IF.

2.4. Button Functions

The UV-K5 features a PTT button, programmable side keys, and a numeric keypad for various operations.

PTT Key (Transmitting Button)

  • Press to transmit and speak into the microphone. Release to receive.

Programmable Keys and Their Functions

  • Side Key 1: Short press for Monitor function; Long press for 1750Hz tone.
  • Side Key 2: Short press for Jacklight; Long press for Emergency Alarm.

Functions configurable via programming software:

  • Emergency Mode On/Off: Activates emergency alarm as per software settings.
  • High/Low Output Power Selection: Switches between High/Low output power.
  • Monitor: Activates/deactivates Monitor function, ignoring CTCSS/DCS to listen to actual channel noise.
  • FM Radio: Toggles FM Radio Mode.
  • Scan On/Off: Toggles Scan function.
  • VOX On/Off: Toggles VOX function.
  • Transmitting 1750: Activates 1750 continuous transmitting.
  • Jacklight: Toggles the flashlight.
Close-up of the Quansheng UV-K5 showing the flashlight function.

Image: A close-up view of the top of the Quansheng UV-K5 walkie-talkie, showing the integrated flashlight in operation.

Keypad Keys

  • Menu/Confirm Key (MENU): Short press to enter menu, select item, and confirm. Long press to enter last setting item. In DTMF, it means 'A' code word.
  • Exit/Clear Key (EXIT): Short press to exit current menu/clear input. Long press to return to main page. In DTMF, it means 'D' code word.
  • Up/Down Keys: Navigate menus. In DTMF, 'B' and 'C' code words respectively.
  • * Key: Short press for manual dial/call page. Long press to start frequency or channel scanning. In DTMF, it means '*' code word.
  • F Key: Works with 0-9 and * for quick function switching. Long press to lock/unlock keypad. In DTMF, it means '#' code word.

2.5. Charging the Battery

Battery packs are not charged when shipped; charge them before use. Initial charging or charging after extended storage (over 2 months) may not yield full capacity immediately. Full capacity is achieved after 2-3 charge/discharge cycles.

Important Charging Notes:

  • Always power off the radio before charging. Do not use the radio during charging, as this can affect normal charging and cause accidents.
  • Once fully charged, remove the battery pack from the charger-base. Do not recharge until the battery is completely depleted to avoid memory effect.
  • If battery life does not improve after proper charging, it indicates the battery is at the end of its life and should be replaced.
  • Use only original factory battery packs and chargers. Non-original accessories can cause dangerous accidents.
  • The Type-C charging port on the radio body is for emergency charging only. For regular charging, use the original factory charger.
  • Do not remove the battery when using Type-C charging.
  • Never attempt to remove the casing from the battery pack.
Quansheng UV-K5 walkie-talkie being charged via Type-C cable and charging dock.

Image: The Quansheng UV-K5 walkie-talkie shown charging in two ways: directly via a Type-C cable in a car, and using its dedicated charging dock with a standard power plug.

3. Operation

3.1. Main Features

The Quansheng UV-K5 offers a wide array of features for versatile communication:

  • 200 Channels
  • Cross-Band Intercom
  • 1750Hz Call Tone
  • Program On Site
  • Emergency Alert
  • FM Radio
  • 10-Group Scrambler
  • Multi-Scan
  • CTCSS/DCS
  • Remote Kill/Revive
  • Keypad Lock
  • Jacklight
  • PC Programmable
  • Busy Channel Lock
  • VOX (Voice Operated Transmit)
  • Dual-watch operation
  • Time-Out-Timer
  • Reset Function
  • Large LCD Display
  • Voice Prompt
  • Reminding Switch
  • Multi Display of Channel No./Channel Frequency/Channel Name
  • H (High), M (Medium), L (Low) Output Power Selective
  • Multi-Band Transmitting & 50-600MHz Receiving
  • Receive/Transmit Code Setting Separately
  • High Capacity Battery/Long Standby Time
  • Fast Copy One Channel (Acts as Frequency Meter for two-way radio & some other devices)
  • 10 Emergency Weather Channels (NOAA)
  • Power-on Password Protection
  • AM/FM Aviation Band Receiving
  • Reverse Frequency Function
  • Type-C And Charger-Base Charging
  • Wide/Narrow Bandwidth
  • Offset Frequency Direction Set
  • Wireless Radio Replication
  • Squelch Level Adjustable
  • Repeater Forwarding Confirmation Function
  • Frequency And Channel Mode Shift
  • Offset Frequency Setting
  • Channel Scan And Add
  • DTMF Calling
  • DTMF ANI
  • DTMF Select Call (single call, group call, all call)
  • Backlight Auto Off Time Selective
  • Automatic Signaling Search
  • Multi Step Frequency
  • One Key Call Channel

3.2. Menu Information

To access the menu, short press the MENU key. Use the Up/Down keys to navigate and the MENU key to confirm selections. Long press EXIT to return to the main page.

The menu structure includes settings for Squelch Level, Step Frequency, Output Power, various CTCSS/DCS settings, Frequency Deviation, Channel Bandwidth, Encryption, Busy Channel Lock, Channel Save, Battery Save, VOX, Auto Backlight, Dual-watch, Scan Resume Mode, Channel Display Mode, Auto Keypad Lock, Scan List management, Tail Tone Elimination, MIC Sensitivity, One Key Call Channel, Alarm Mode, DTMF settings (ANI-ID, UP/DOWN CODE, Side Tone, Decoding Response, Auto Reset Time, Pre-load Time, PTT-ID TX Mode, Decoding Enable, Contact List, Power On Message), End Talk Reminding, Battery Voltage, AM Channel Mode, NOAA Channel Auto Scan, Channel Delete, and Reset.

3.3. Common Operations

3.3.1. Power On Password Protection

Turn the Power/Volume Switch clockwise to power on. If password protection is set, the screen will show 'LOCK'. Enter the password to use the radio.

3.3.2. Switch Main Channel

Press F+2 to switch the main channel. The solid arrow indicates the main channel. Press PTT to transmit on the main channel.

3.3.3. Dual Band Single-Watch/Dual-Watch Switch

Set dual-watch mode via MENU → 17 (TDR). Select CHAN_A or CHAN_B as the default TX channel. The screen will show 'DW'.

3.3.4. Frequency/Channel Mode Switch

On the main page, press F+3 to switch between Frequency Mode and Channel Mode.

  • Frequency Mode: Manually input RX frequency or adjust with Up/Down keys. TX frequency cannot be directly input but can be changed by setting Offset Frequency.
  • Channel Mode: Displays current channel number. Manually input channel number or use Up/Down keys to switch channels.

3.3.5. Cross-Band Receiving/Transmitting

Set via MENU → 18 (WX). When CHAN_A or B receives a valid call, the channel automatically becomes the main TX channel until the call ends. 'WX' character will be displayed.

3.3.6. Channel Save

In MR Mode, save the current channel to a new channel. In VFO Mode, set RX Frequency, Frequency Deviation, Bandwidth, CTCSS/DCS, TX Power, Scanning participation, DTMF code, Scrambler, etc. Then MENU → 13 (MEM-CH) to save. Select channel with Up/Down or Number keys, press MENU again, 'SURE?' will appear, press MENU to save. 'CH-XXX' indicates a saved channel, 'XXX' indicates an empty channel.

3.3.7. Channel Delete

MENU → 50 (DEL-CH). Select the channel to delete with Up/Down or Keypad. Press MENU, 'SURE?' will appear, press MENU to delete.

3.3.8. Receiving/Transmitting CTCSS/DCS Setting

Set RX DCS (MENU → 4), RX CTCSS (MENU → 5), TX DCS (MENU → 6), TX CTCSS (MENU → 7). CTCSS/DCS removes unwanted noise signals.

3.3.9. Fast Copy One Channel (Frequency Meter)

Requires strong signal and antennas on both TX and RX radios. Press F+4 on the receiver to enter Frequency Meter. When a strong signal is received, the LCD displays carrier frequency and TX channel (CTCSS or DCS). Press * to re-measure. Press MENU to save measured frequency and CTCSS/DCS to a specified channel. Press EXIT or PTT to exit.

Set correct RX frequency, then press F+* to start search. When valid CTCSS/DCS is received, it displays the searched TX CTCSS/DCS. Press MENU to save. 'SCAN CMP' means valid signal found, 'SCAN FAIL' means no valid signal found.

3.3.11. DTMF (Dual Tone Multi-Frequency)

  • DTMF Calling: Manual dialing: Press PTT and keypad number. Automatic calling: Press *, enter 3 digits, short press PTT. Sends its own ID. Single call: Send other party's ID + own ID (e.g., 123*100). Group call: Use group calling code (set by software) to call a group. All call: Send ###.
  • PTTID: Configure DTMF online/offline codes via software. Online code sent on PTT press, offline code on PTT release.

3.3.12. Scanning

Start scanning by long pressing * key or setting a side key. During frequency scanning, change direction with Up/Down keys. During channel scanning, detect channels in scan list. Answer incoming calls by pressing PTT.

3.3.13. Emergency Alarm

Used for emergency situations. Can be initiated anytime. Configure emergency alarm button via programming software. Press the button to activate local audible/light alarm and remote alarm. Alarm type can be set as local/remote. Exit alarm mode by any key. Process: MENU → 34 (AL-MOD TONE for alarm sound + remote signal, AL-MOD SITE for alarm sound only).

3.3.14. FM Radio

Press F+0 to enter FM radio mode. Change frequency/pre-stored channels with Up/Down keys or keypad. F+1 switches between VFO/MR. F+2 starts auto search (stores up to 20 channels). F+3 starts manual search (manual store required). MENU key stores FM channel. EXIT key exits search. Up/Down keys change scan direction. If a call is received or PTT is pressed, FM mode temporarily exits for communication, then returns. Press EXIT or F+0 to exit FM mode.

3.3.15. Emergency Weather Channel Receiving (NOAA)

Press F+5 to enter/exit NOAA Weather Alert. This radio can receive 10 NOAA channels. Mode set via MENU → 49 (NOAA_S).

Quansheng UV-K5 highlighting NOAA Meteorological reception and AM/FM segment reception.

Image: The Quansheng UV-K5 walkie-talkie displaying its capability for NOAA Meteorological reception and AM/FM segment reception, indicating its multi-functional receiving capabilities.

3.3.16. Keypad Locking

Long press the # key to lock/unlock all keypad keys. Side keys remain functional when locked.

3.3.17. Reset

Process: MENU → 51 (RESET). VFO resets parameters except channel parameters. ALL resets all parameters. Press MENU when 'SURE?' appears, radio restarts, all options return to factory defaults.

3.3.18. One Key Call Channel

F+9 immediately jumps to one key call channel. Set important channel via MENU → 30 (1-CALL).

3.3.19. Aviation Band Receiving

Enter RX frequency. If local aviation frequency is unknown, use scan function (108-136 full frequency band). MENU → 48 (AM ON) sets channel modulation to AM for aviation intercom. MENU → 48 (AM OFF) sets to FM. Menu 48 settings are only valid for 108-136MHz band.

3.3.20. Wireless Radio Replication

Hold PTT + Side Key 2 to enter Wireless Radio Replication interface. LCD displays 'Air Copy (RDY)'. Both TX and RX radios must have consistent frequencies (default 410.0125MHz). Press EXIT on RX radio for receiving mode. Press MENU on TX radio to start data transmission. LCD displays copy progress (RCV:XX E:XX, E:XX indicates errors). 'SND: 120' displayed when finished.

4. Maintenance

4.1. General Precautions

  • Keep the radio and all accessories out of reach of children.
  • Maintenance should only be performed by professional technicians.
  • Use only the standard battery pack and charger to avoid damaging the radio.
  • Use the standard antenna to maintain communication distance.
  • Do not expose the radio to direct sunlight for long periods or near heat sources.
  • Avoid extreme dust or wet environments.
  • Do not clean the radio with harsh chemical products, cleaning agents, or strong washing agents.

4.2. Battery Care

  • Recycle the battery pack to protect the environment.
  • Do not remove the battery when using Type-C charging.
  • Never attempt to remove the casing from the battery pack.

5. Troubleshooting

  • If you detect a strange smell or smoke from the radio, immediately turn off the radio, remove the battery, and contact your agent.
  • If the equipment causes harmful interference to radio or television reception, try to correct it by:
    • Reorienting or relocating the receiving antenna.
    • Increasing the separation between the equipment and receiver.
    • Connecting the equipment to an outlet on a different circuit.
    • Consulting the dealer or an experienced radio/TV technician.

6. Specifications

6.1. General Specifications

ParameterValue
Channel200
Stored FM Radio Channel Quantity20
NOAA Channel Quantity10
Frequency Stability±1ppm
Modulation ModeFM: 11KΦF3E (12.5KHz), 16KΦF3E (25KHz)
Dimensions115*60*37.5mm
Weight234g
Operating Temperature-20°C to +60°C
Antenna Impedance50Ω
Battery Capacity1600mAh

6.2. Transmitting Specifications

ParameterFCC VersionCE/UKCA VersionNORMAL VersionIC Version
FrequencyUHF420-450MHz, VHF144-148MHzUHF430-440MHz, VHF144-146MHzUHF400-470MHz, VHF136-174MHz, UHF350-400MHzUHF430-450MHz, VHF144-148MHz
Output Power≤5W≤5W≤5W≤5W
Emission Current≤1.5A≤1.5A≤1.5A≤1.5A
Max Frequency Deviation≤5KHz(25KHz), ≤2.5KHz(12.5KHz)≤5KHz(25KHz), ≤2.5KHz(12.5KHz)≤5KHz(25KHz), ≤2.5KHz(12.5KHz)≤5KHz(25KHz), ≤2.5KHz(12.5KHz)
Modulation Distortion≤5%≤5%≤5%≤5%
Stray Power<7.5uW<7.5uW<7.5uW<7.5uW
Adjacent Channel Power70dB(25KHz), 60dB(12.5KHz)70dB(25KHz), 60dB(12.5KHz)70dB(25KHz), 60dB(12.5KHz)70dB(25KHz), 60dB(12.5KHz)
Residual Modulation40dB40dB40dB40dB

6.3. Receiving Specifications

ParameterValue
Frequency Range (F1)50-76MHz
Frequency Range (F2)108-135.9975MHz
Frequency Range (F3)136-173.9975MHz
Frequency Range (F4)174-349.9975MHz
Frequency Range (F5)350-399.9975MHz
Frequency Range (F6)400-469.9975MHz
Frequency Range (F7)470-599.9975MHz
Sensitivity (FM, 12dB SINAD)F1: -121dBm, F2: -121dBm, F3: -123dBm, F4: -123dBm, F5: -123dBm, F6: -123dBm, F7: -121dBm
Sensitivity (WFM, 20dB SINAD)76-108MHz: -110dBm
Sensitivity (AM, 10dB S/N)108-135.9975MHz: -113dBm
Audio Frequency≥0.5W
Audio Distortion≤10%

Note: All stated specifications are subject to change without notice or obligation due to technical improvements.

7. User Tips

  • Custom Firmware: The UV-K5 is known to be compatible with custom firmware like 'egzumer 0.22' for enhanced functionality. Users interested in advanced features may explore this option.
  • Hardware Versions: Be aware that there are different hardware versions (e.g., V2, V3). Some advanced modifications or custom firmware might require a specific hardware version. Check your radio's version (often on the back label) if you plan extensive modifications.
  • Air Band Reception: The radio is capable of receiving air band frequencies (108-135.9975MHz AM).

8. Warranty and Support

8.1. EU Declaration of Conformity

The radio equipment type listed in the technical specifications is in compliance with Directive 2014/53/EU.

8.2. Disclaimer

The accuracy and completeness of the contents are sought in the process of compilation, but we do not bear any responsibility for possible errors or omissions. With the continuous development of technology, we reserve the right to change the design and specification of the product without notice. No copy, modification, translation, and dissemination of this handbook may be made in any form without the prior written authorization of our department.

User manual cover page with FCC, CE, UKCA, IC, RoHS logos.

Image: The cover page of the user manual, displaying compliance logos including FCC, CE, UKCA, IC, and RoHS, along with the text 'USER MANUAL TWO WAY RADIO'.

8.3. Additional Resources

A detailed user manual in PDF format is available for download. You can access it via the following link: Quansheng UV-K5 User Manual (PDF).


Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.