1. Safety Information
1.1 FCC Compliance Statements
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
This device complies with FCC radiation exposure limits set forth for an uncontrolled environment. Do not use this device when the antenna shows obvious damages. Hold this transmitter approximately 25 mm away from your face and speak normal with the antenna pointed up and away. Use the supplied belt clip for body-worn configuration as other accessories may not comply to the limits.
WARNING: MODIFICATION OF THIS DEVICE TO RECEIVE CELLULAR RADIOTELEPHONE SERVICE SIGNALS IS PROHIBITED UNDER FCC RULES AND FEDERAL LAW.
1.2 CE Warning
Use the two-way radio in an environment with temperatures between 0-40°C; otherwise, it may damage your two-way radio. It can be operating under 2000m. Hereby, we declare that the radio equipment type two-way radio is in compliance with Directive 2014/53/EU. For this device, Head SAR and Body SAR were performed with the device configured in the positions according to EN62209-2:2010, and face-up SAR was performed with the device 25mm from the phantom, and Body SAR was performed with the device 0mm from the phantom. Body SAR was also performed with the headset and belt clip attached and without.
1.3 General Precautions Before Using
- Please put the radio and accessories where children cannot reach.
- Maintenance can only be performed by professional technicians.
- Please use the standard battery pack and charger in order not to destroy the radio.
- Please use the standard antenna, in order not to shorten the communication distance.
- Do not expose the radio to sunlight for a long period of time, nor put it near heat.
- Do not put it in extreme dust or wet environments.
- Do not clean the radio with fierce chemical products, cleaning agents or strong washing agents.
- Do not transmit when the antenna is not installed.
- If you find a bad smell or smoke, please turn off the radio immediately. And take the battery off the radio, then contact the agent.
2. Supplied Accessories
Carefully unpack the portable radio. We suggest that you check the following items before you throw away the packing materials.
2.1 Standard Accessories List
| Item | Qty |
|---|---|
| Portable Radio | 1 |
| Antenna | 1 |
| Li-ion Battery | 1 |
| Battery Charger | 1 |
| Belt Clip | 1 |
| User's Manual | 1 |
2.2 Accessories Photo





3. Radio Diagram
Familiarize yourself with the components of your Quansheng UV-K6 Walkie Talkie.



3.1 Indicator Details
- Red Light: Transmitting
- Green Light: Receiving
- Blue Light: On when Charging / Off when the radio is fully charged.
4. LCD Display Explanation
The LCD screen displays various symbols to indicate the radio's status and settings. Refer to the table below for their meanings:
| Symbol | Description |
|---|---|
| Signal Strength Icon | Indicates signal strength. Fewer bars mean weaker signal. |
| HML | Transmitting Output Power Indicator (H: High, M: Medium, L: Low). |
| CT DCS | CT appears when current code is CTCSS code. DCS appears when current code is DCS code. |
| D | Voice prompt is on. |
| N | The radio works in narrow band mode. |
| VOX | VOX Function. When the sound pressure reaches the set value, transmission is started. This function can be set through the menu. |
| +- | + means transmitting frequency equals receiving frequency plus a frequency deviation. - means transmitting frequency equals receiving frequency minus a frequency deviation. |
| DTMF | DTMF signal decoding is on. |
| DW | Frequency dual watch is on. Can display two frequency bands. |
| Keypad Lock Icon | Keypad locking is active. |
| Battery Icon | Display of the current battery. When nearly exhausted, it shows an icon and the radio will send a low power alarm. |
| Main Channel Indicator | Indicates the main channel. All operations work on the main channel. |
| SCR | The voice encryption of this channel is on. |
| R | Reverse mode. Receive and transmit frequency reverse. |
| Scanning Icons | Indicates participation in scan list 1 or 2. |
| WX | Cross-Band Receiving/Transmitting. |
| RX | Receiving. |
| TX | Transmitting. |
| Type-C Charging Mark | Indicates Type-C charging. |
| AM | AM receiving mark. |
| NS | NOAA channel automatic scan. |
5. Key Functions
5.1 PTT Key (Transmitting Button)
- Press and hold the PTT button to transmit and speak into the microphone. Release PTT to receive.
5.2 Programmable Key and Its Function
The side keys can be programmed via software.
- Side Key 1: Short press for Monitor function. Long press for 1750Hz.
- Side Key 2: Short press for Jacklight. Long press for emergency alarm.
5.3 Keypad Key
- Menu/Confirm Key (MENU): Short press to enter the menu, select an item, and press again to confirm. Long press to enter the last setting item. Under DTMF, it means 'A' code word.
- Exit/Clear Key (EXIT): Short press in edit status to return to the upper menu. Long press to return to the main page. In input status, clears input info. Under DTMF, it means 'D' code word.
- Up Key: Moves upward. Under DTMF, it means 'B' code word.
- Down Key: Moves downward. Under DTMF, it means 'C' code word.
- * Key: Short press to enter manual dial and call page. Long press to start frequency or channel scanning. Under DTMF, it means '*' code word.
- F Key: Function key. Short press F + (0-9, *, #) to quickly switch functions. Long press to lock/unlock the keypad. Under DTMF, it means '#' code word.
| Key Combination | Function | Description |
|---|---|---|
| F+1 | BAND | (F1-F7) Frequency Switch |
| F+2 | A/B | Main Channel Switch |
| F+3 | VFO/MR | Switch between VFO and MR Mode |
| F+4 | Frequency Meter | Start Fast Copy One Channel |
| F+5 | NOAA Weather Alert | Start or Exit NOAA Channel |
| F+6 | H/M/L | Switch Output Power |
| F+7 | VOX | Switch to VOX |
| F+8 | R | Switch to Reverse Function |
| F+9 | CALL | Switch to one key emergency calling |
| F+* | SER | Start CTCSS/DCS Search Function |
| F+0 | FM | Start or Exit FM |
6. Menu Information
Press the MENU key to enter Menu Selection; Press Up/Down Key to select Menu No., and press MENU Key to confirm the selection; Press EXIT Key to return to Upper Menu. Long press EXIT key to return to main page.
| Item Name | No. | Function Description | Value Range |
|---|---|---|---|
| SQL | 1 | Squelch Level | 0-9 |
| STEP | 2 | Step Frequency (2.5K/5K/6.25K/10K/12.5K/25K) | 0-5 |
| TXP | 3 | Output Power (LOW/MID/HIGH) | 0-2 |
| R_DCS | 4 | Receive DCS (OFF, 1-104:DCS, 105-208: reverse DCS). Short Press F+* to trigger DCS scanning. | 0-208 |
| R_CTCS | 5 | Receive CTCSS (OFF, 1-50: CTCSS). Short Press F+* to trigger CTCSS scanning. | 0-50 |
| T_DCS | 6 | Transmit DCS (OFF, 1-104: DCS, 105-208: reverse DCS) | 0-208 |
| T_CTCS | 7 | Transmit CTCSS (OFF, 1-50: CTCSS) | 0-50 |
| SFT-D | 8 | Frequency Deviation Setting (OFF:TX frequency =RX frequency; ADD: TX frequency=RX frequency + frequency deviation; SUB: TX frequency=RX frequency-frequency deviation) | 0-2 |
| OFFSET | 9 | Frequency of Frequency Deviation (0-999.9999M) | |
| W/N | 10 | Channel Bandwidth (0:WIDE, 1:NARROW) | 0-1 |
| SCR | 11 | Encrypted Communication (OFF, 1-10: 1 to 10 types of scrambling frequency.) | 0-10 |
| BCL | 12 | Busy Channel Lock (OFF,ON) | 0-1 |
| MEM-CH | 13 | Channel Save (Choose the channel by Up/Down Key and Number Key, press MENU key to Save the channel.) | |
| SAVE | 14 | Battery Save (OFF/1:1/1:2/1:3/1:4) The rate between active time and sleep time. | 0-4 |
| VOX | 15 | VOX Setting (OFF: turn off VOX, 1-10: 1 to 10 grade.) | 0-10 |
| ABR | 16 | Auto Backlight (OFF: turn off Backlight; 1-5: turn off Backlight in 1-5 seconds) | 0-5 |
| TDR | 17 | Dual-watch On/Off (OFF: Close, CHAN_A: Default TX Channel is A channel, CHAN_B: Default TX Channel is B channel.) | 0-2 |
| WX | 18 | Cross-Band Receiving/Transmitting (OFF: Close, CHAN_A: TX Channel is A channel, CHAN_B: TX Channel is B channel.) | 0-2 |
| BEEP | 19 | BEEP Control (OFF, ON) | 0-1 |
| TOT | 20 | Time-Out-Timer (1-10min) | 1-10 |
| VOICE | 21 | Voice Prompt (OFF, CHI: Chinese, ENG: English) | 0-2 |
| SC-REV | 22 | Scan Resume Mode (TO: Resume scan after 5 seconds pause; CO: Resume scan after signal disappear; SE: After receive the signal, stop scan.) | 0-2 |
| MDF | 23 | Channel Display Mode (FREQ: Display frequency. CH: Display channel No., NAME: Display channel name) | 0-2 |
| AUTOLK | 24 | Auto Keypad Lock (OFF,ON) | 0-1 |
| S-ADD1 | 25 | Whether to participate in list 1 scanning (OFF: not participating, ON: participation) | 0-1 |
| S-ADD2 | 26 | Whether to participate in list 2 scanning (OFF: not participating, ON: participation) | 0-1 |
| STE | 27 | Tail Tone Elimination (OFF,ON) | 0-1 |
| RP-STE | 28 | Repeater Tail Tone Elimination (OFF,ON) | 0-1 |
| MIC | 29 | MIC Sensitivity (0-4: 0-4 level) | 0-4 |
| 1-CALL | 30 | One Key Call Channel (Select the channel through the Up/Down keys and the Number keys) | |
| S-LIST | 31 | Channel Scan List Select (LIST1: Scan list 1; LIST2:Scan list 2) | 1-2 |
| SLIST1 | 32 | Channel Scan List 1 Configuration | |
| SLIST2 | 33 | Channel Scan List 2 Configuration | |
| AL-MOD | 34 | Alarm Mode (SITE: local alarm; TONE: Distant + local alarm) | 0-1 |
| ANI-ID | 35 | ANID, DTMF communication radio ID | |
| UPCODE | 36 | DTMF UP CODE | |
| DWCODE | 37 | DTMF DOWN CODE | |
| D-ST | 38 | DTMF Side Tone Switch (OFF, ON) | 0-1 |
| D-RSP | 39 | DTMF Decoding Response (NULL: Close, Ring: Local ringing, REPLY: reply response, both: local ringing +reply response) | 0-3 |
| D-HOLD | 40 | DTMF Auto Reset Time (5s-60s) | 5-60 |
| D-PRE | 41 | DTMF pre-load time (30-990ms) | 3-99 |
| PTT-ID | 42 | DTMF PTT-ID TX Mode (OFF: Close, BOT: Press PTT to send UP CODE, EOT: Release PTT to send DOWN CODE, BOTH: Press or release PTT to send.) | 0-3 |
| D-DCD | 43 | DTMF decoding enable signal (OFF,ON) | 0-1 |
| D-LIST | 44 | DTMF Contact List (Choose the contact by Up/Down Key and Number Key, press MENU key to select the contact and call directly.) | 1-16 |
| PONMSG | 45 | Displays of Power On (FULL: full screen display. MSG: Welcome info, VOL: Voltage. It can modify it by program software.) | 0-2 |
| ROGER | 46 | Reminding of End Talk (OFF: no reminding, ROGER: with reminding, MDC: Frog Sound Tail Tone) | 0-2 |
| VOL | 47 | Battery Voltage | 0-1 |
| AM | 48 | AM Channel Mode On/Off (Used only for 108-136MHz) | 0-1 |
| NOAA_S | 49 | NOAA Channel Auto Scan On/Off | |
| DEL_CH | 50 | Channel Delete (Choose the channel by Up/Down Key and Number Key, press MENU key to delete the channel.) | |
| RESET | 51 | Reset (VFO: Reset parameter beside channel parameter; ALL: Reset all parameter.) | 0-1 |
7. Common Operation
7.1 Power On Password Protection
Turn the Power/Volume Switch clockwise to power on the radio. If a password is set, the screen will show "LOCK". Input the password to use the radio normally.
7.2 Switch Main Channel
Press F+2 to switch the main channel. The solid arrow indicates the main channel. Press PTT to transmit in the main channel.
7.3 Dual Band Single-Watch/Dual-Watch Switch
Dual-watch operation mode can be set via the menu (MENU → 17). Select CHAN_A or CHAN_B as the default TX channel. The screen will show "DW".
7.4 Frequency/Channel Mode Switch
In the main page, press F+3 to switch between Frequency Mode and Channel Mode.
- Frequency Mode: Manually input RX frequency or adjust with Up/Down keys. TX frequency cannot be directly input but can be changed by setting Frequency Deviation.
- Channel Mode: Displays current channel number. Manually input channel number or adjust with Up/Down keys.
7.5 Cross-Band Receiving/Transmitting
Set via MENU → 18 → WX. When CHAN_A or B receives a valid call, it becomes the main channel until the call ends. "WX" character is displayed.
7.6 Channel Save
- MR Mode: Copy current channel to a new channel.
- VFO Mode: Set RX Frequency, Frequency Deviation Direction, Wide/Narrow Bandwidth, RX/TX CTCSS/DCS, TX Output Power, Scanning participation, DTMF code, Scrambler, etc. Then press MENU → 13 → CH-001, then MENU again to enter Channel Save. Select channel with Up/Down Key or Number Key. Press MENU again, screen shows "SURE?". Press MENU again to save.
- If a saved channel shows CH-XXX, it's saved. If it shows XXX, it's empty.
7.7 Channel Delete
Press MENU → 50 → CH-XXX, then MENU again to enter Channel Delete. Select the channel to delete with Up/Down Key or Keypad. Press MENU again, screen shows "SURE?". Press MENU again to delete.
7.8 Receiving/Transmitting CTCSS/DCS Setting
CTCSS/DCS is used to remove unwanted noise signals when receiving.
- RX DCS: MENU → 4 → R-DCS. Select desired DCS code.
- RX CTCSS: MENU → 5 → R-CTCS. Select desired CTCSS frequency.
- TX DCS: MENU → 6 → T-DCS. Select desired TX DCS code.
- TX CTCSS: MENU → 7 → T-CTCS. Select desired TX CTCSS frequency.
7.9 Fast Copy One Channel / Frequency Meter
Requires a strong signal. Both TX and RX radios need antennas and should be close. Press F+4 to enter Frequency Meter interface. When a strong signal is received, LCD displays carrier frequency and TX channel (CTCSS or DCS). Press * to re-measure. After measuring, press MENU to save frequency and CTCSS/DCS to a specified channel. Press EXIT or PTT to exit.
7.10 Auto CTCSS/DCS Search
Set correct RX frequency, then press F+* to start channel searching. When a valid CTCSS/DCS signal is received, it displays the searched TX CTCSS/DCS signal. Press MENU to save. If screen shows SCAN CMP, a valid signal was found. If SCAN FAIL, no valid signal was found.
7.11 DTMF
7.11.1 DTMF Calling
- Manual dialing: Press PTT and keypad number key.
- Automatic calling: Press *, enter 3 digits, short press PTT. Sends own ID.
- Single call: Send other party's ID + own ID (e.g., 123*100 for ID 100 to call ID 123).
- Group call: Use a group calling code (set by software). E.g., #, send 12# to call 10 radios (ID 120-129).
- All call: Send ### to call all users.
7.11.2 PTTID
Configure DTMF online and offline codes via software. When enabled, radio sends online code on PTT press, and offline code on PTT release.
7.12 Scanning
- Start Scanning: Long press * Key or set Side Key as Scanning Start/Close Switch.
- Frequency Scanning: Change scan direction with Up/Down key. Press PTT or EXIT or long press * to exit.
- Channel Scanning: Detects channels in scan list. Answer incoming calls with PTT.
- Scan List Configuration: MENU → 31 → S-LIST (LIST1 or LIST2). View channels in list (MENU → 32/33). Add current channel to list (MENU → 25/26). Select scanning mode (MENU → 22 → SC-REV).
- Priority Scanning: 50% of scanning is on priority 1 members. If priority 2 members exist, priority 1 scanning reduces to 25%. Radio continues scanning priority 1 activity even on non-priority channels.
7.13 Emergency Alarm
Used for emergency situations. Can initiate calls anytime, anywhere. Configure emergency alarm button via software. Press the button to activate local audible alarm and remote alarm. Type can be local/remote. Exit with any key.
- Process (Tone): MENU → 34 → AL-MOD TONE. Radio makes alarm sound and sends remote alarm signal.
- Process (Site): MENU → 34 → AL-MOD SITE. Radio makes alarm sound.
7.14 FM Radio
Press F+0 to enter FM radio mode. Use Up/Down keys or keypad to change frequency/channels. Press F+1 to switch between VFO and MR mode. Press F+2 for auto search (stores up to 20 channels). Press F+3 for manual search (store manually). MENU key stores FM channel. EXIT key exits search. Up/Down keys change scan direction. If radio receives calls or PTT is pressed, it temporarily exits FM mode. Press EXIT or F+0 to exit FM mode.
7.15 Emergency Weather Channel Receiving
Press F+5 to enter or exit NOAA Weather Alert. Receives 10 NOAA channels. Set mode via MENU 49 NOAA_S.
7.16 Keypad Locking
Long press # key to lock or unlock all keys. Side keys work normally when locked.
7.17 Reset
Process: Press MENU → 51 → RESET.
- VFO: Reserves all storage channels.
- ALL: Resets all parameters, including storage channels.
7.18 One Key Call Channel
F+9 immediately jumps to one key call channel. Set important channel via MENU → 30 → 1-CALL.
7.19 Aviation Band Receiving
Enter RX frequency. If local aviation frequency is unclear, scan 108-136 full frequency band. MENU 48 → AM ON sets channel modulation to AM. MENU 48 → AM OFF sets to FM. Settings only valid for 108-136MHz band.
7.20 Wireless Radio Replication
Hold PTT + Side Key 2 to enter Wireless Radio Replication interface. LCD displays Air Copy (RDY). Both TX and RX radios can use digital keypad to set frequency. Frequencies must be consistent. Default RX/TX frequency is 410.0125MHz. Press EXIT on RX radio to enter RX mode. Press MENU on TX radio to start transmitting data. LCD displays copy progress (RCV:XX E:XX for errors). When complete, TX displays SND: 120.
8. User Tips
- Beginner-Friendly: This radio is easy to use, even for beginners, offering a great entry point into two-way radio communication.
- Durability: Users report the radio is solid and durable, with some noting it withstands drops well.
- Reception Quality: The radio generally offers good reception across various frequencies.
- Value for Money: Highly recommended for its affordability and excellent performance.
- Frequency Scanning: Ideal for scanning a wide range of frequencies.
- Firmware Upgrades: The firmware is upgradeable. Check for the latest versions (e.g., 7.0.15) to enhance functionality. A video demonstrating the firmware upgrade process is available:
Video: Demonstrating the firmware upgrade process for the Quansheng UV-K6.
- Third-Party Firmware: The radio supports flashing with third-party firmware (e.g., SHIRP) to enable additional features like LPD and PMR channels.
- Charger Compatibility: Always verify the charger plug type to ensure it matches your region's electrical outlets.
9. Troubleshooting
9.1 Charging Issues
- Battery Not Charging: Ensure the battery is correctly inserted into the charger. For Type-C charging, ensure the cable is properly connected. The blue light indicates charging, and it turns off when fully charged.
- Slow Charging: Type-C charging is primarily for emergency use. For normal charging, use the provided charger base.
- Charging Indicator: When charging via Type-C while powered on, a charging symbol appears on the top right of the screen.
9.2 Communication Issues
- Short Communication Distance: Ensure the antenna is properly installed and is the standard antenna provided.
- Interference: If experiencing interference, try reorienting the antenna, increasing separation from other equipment, or connecting to a different circuit.
- Firmware Discrepancies: If the operating frequency range or firmware version differs from expectations, consider upgrading the firmware using the provided software and programming cable.
9.3 Firmware Upgrade Process
- In shutdown state, press and hold the PTT transmission button.
- Power on the device while holding PTT to enter upgrade mode.
- Connect the programming cable to the computer and the walkie-talkie.
- Download firmware and software from the official website (refer to the user manual PDF for links).
- Select the corresponding COM port in the software.
- Select the firmware file.
- Choose to upgrade and wait for the progress bar to complete.
- Once writing is complete, restart the device.
10. Specifications
10.1 General Specifications
| Parameter | Value |
|---|---|
| Channel | 200 |
| Stored FM Radio Channel Quantity | 20 |
| NOAA Channel | 10 |
| Frequency Stability | ±1ppm |
| Modulation Mode | FM:11KΦF3E(12.5KHz), 16KΦF3E(25KHz) |
| Dimension | 115mm x 60mm x 37.5mm |
| Weight | 234g |
| Operating Temperature | -20°C ~ +60°C |
| Antenna Impedance | 50Ω |
10.2 Transmitting Specifications
| Parameter | FCC Version | CE/UKCA Version | NORMAL Version | IC Version |
|---|---|---|---|---|
| Frequency | UHF420-450MHz, VHF144-148MHz | UHF430-440MHz, VHF144-146MHz | UHF400-470MHz, VHF136-174MHz, UHF350-400MHz | UHF430-450MHz, VHF144-148MHz |
| Output Power | ≤5W | ≤5W | ≤5W | ≤5W |
| Emission Current | ≤1.5A | ≤1.5A | ≤1.5A | ≤1.5A |
| Max Frequency Deviation | ≤5KHz(25KHz), ≤2.5KHz(12.5KHz) | ≤5KHz(25KHz), ≤2.5KHz(12.5KHz) | ≤5KHz(25KHz), ≤2.5KHz(12.5KHz) | ≤5KHz(25KHz), ≤2.5KHz(12.5KHz) |
| Modulation Distortion | ≤5% | ≤5% | ≤5% | ≤5% |
| Stray Power | <7.5uW | <7.5uW | <7.5uW | <7.5uW |
| Adjacent Channel Power | 70dB(25KHz), 60dB(12.5KHz) | 70dB(25KHz), 60dB(12.5KHz) | 70dB(25KHz), 60dB(12.5KHz) | 70dB(25KHz), 60dB(12.5KHz) |
| Residual Modulation | 40dB | 40dB | 40dB | 40dB |
10.3 Receiving Specifications
| Parameter | Frequency Range | Sensitivity |
|---|---|---|
| Sensitivity (FM, 12dB SINAD) | F1 (50-76MHz) F2 (108-135.9975MHz) F3 (136-173.9975MHz) F4 (174-349.9975MHz) F5 (350-399.9975MHz) F6 (400-469.9975MHz) F7 (470-599.9975MHz) | -121dBm -121dBm -123dBm -123dBm -123dBm -123dBm -121dBm |
| WFM (20dB SINAD) | WFM (76-108MHz) | -110dBm |
| AM (10dB S/N) | F2 (108-135.9975MHz) | -113dBm |
| Audio Frequency | ≥0.5W | |
| Audio Distortion | ≤10% |
All stated specifications are subject to change without notice or obligation due to technical improvements.
11. Warranty and Support
For detailed information regarding product warranty, please refer to the official user manual PDF available for download. This document contains comprehensive details on warranty terms and conditions.
You can view the full user manual in PDF format here: Quansheng UV-K6 User Manual (PDF).