HeltecBMS HT-616L Series

Contents

HeltecBMS Battery Management System User Manual

Model: HT-616L Series

1. Product Introduction

This manual provides essential information for the safe and efficient operation of your HeltecBMS Battery Management System. The HT-616L series is an intelligent balancing protection board designed for 6S-16S series lithium batteries, supporting both ternary lithium (NCM) and lithium iron phosphate (LiFePO4/LFP) battery types.

Key Features:

  • Overcharge protection
  • Over-discharge protection
  • Over-current protection
  • Over-temperature protection
  • Short circuit protection
  • Balanced charging for extended battery life
HeltecBMS 16S 30A 3.7V BMS module overview

Figure 1: HeltecBMS 16S 30A 3.7V BMS module overview.

2. Product Model Selection

The HeltecBMS HT-616L series is available in various configurations. Please refer to the table below to identify your specific model.

ParameterValue
Number of Strings6S-16S
Continuous Discharge Current30A / 50A / 80A
Applicable Battery TypeNCM (Ternary Lithium) / LFP (Lithium Iron Phosphate)

Note: Customization for 6-16S series is supported.

Product Model Description Example:

A model like HT-616 LOS 12S 50A or HT-616 LPS 12S 50A can be broken down as follows:

  • 616: Indicates the series, supporting 6 to 16 strings.
  • LOS: Indicates compatibility with NCM (Ternary Lithium) batteries.
  • LPS: Indicates compatibility with LFP (Lithium Iron Phosphate) batteries.
  • 12S: Represents the number of series strings this BMS board supports.
  • 50A: Denotes the continuous discharge current rating of this BMS board.

3. Specifications

3.1. General Parameters

ProjectSymbolDetailed ContentStandard
Serial numberSNumber of battery strings6-16S
Internal ResistanceRDSMain circuit on state resistance (battery voltage=3.4V)B- to P- RDS ≤ 0.3mΩ
Consume CurrentIDDInternal consumption of the circuit during operationMIN: 0.3μA MAX: 100μA
Charging MOS MAX withstand voltageVDSMAX voltage value that the charger can withstand when the charging port is connectedDC 100V

3.2. Lithium Iron Phosphate (LFP) Battery Parameters

Test conditions: room temperature 25°C. The over-current value and internal resistance are dynamic parameters. Voltage of each battery cell needs to be >3.25V during testing.

ParameterSymbolValue
Overcharge detection voltageVDET13.65V ± 0.035V
Overcharge detection delay timetVDET11.3s (MAX)
Overcharge relieve voltageVREL13.55V ± 0.025V
Over discharge test voltageVDET22.350V ± 0.025V
Delay time for over discharge detectiontVDET21.5s (MAX)
Over discharge relieve voltageVREL22.55V ± 0.025V
Discharge over-current detection voltageVDET3100mV ± 25mV
Instantaneous single pulse current (tolerated)IDP120A / 200A / 320A
Instantaneous multi-pulse current (withstand)IDP90A / 150A / 240A
Short-circuit detection delay timeTSHORT300μS (MAX)
Electricity balance detection voltageVBU3.405V ± 0.035V
Balance startup delay timetVBU1.6S (MAX)
Battery balance release voltageVBL3.4V ± 0.035V
4.2V battery balance currentIR100mA ± 5mA

3.3. Ternary Lithium (NCM) Battery Parameters

Test conditions: room temperature 25°C. The over-current value and internal resistance are dynamic parameters. Voltage of each battery cell needs to be ≥3.7V during testing.

ParameterSymbolValue
Overcharge detection voltageVDET14.25V ± 0.035V
Overcharge detection delay timetVDET11.3s (MAX)
Overcharge relieve voltageVREL14.2V ± 0.025V
Over discharge test voltageVDET22.8V ± 0.025V
Delay time for over discharge detectiontVDET21.5s (MAX)
Over discharge relieve voltageVREL23.0V ± 0.025V
Discharge over-current detection voltageVDET3100mV ± 5mV
Instantaneous single pulse current (tolerated)IDP120A / 200A / 320A
Instantaneous multi-pulse current (withstand)IDP90A / 150A / 240A
Short-circuit detection delay timeTSHORT300μS (MAX)
Electricity balance detection voltageVBU4.22V ± 0.035V
Balance startup delay timetVBU1.6S (MAX)
Battery balance release voltageVBL4.21V ± 0.035V
3.59V battery balance currentIB100mA ± 5mA

3.4. Dimensions

The length and width of the 6-16S series protection board are consistent. The thickness varies based on the continuous discharge current rating.

HeltecBMS module dimensions diagram

Figure 2: HeltecBMS module dimensions (example 30A).

DimensionValue
Length70mm
Width55mm
Thickness (30A)8mm
Thickness (50A/80A)12mm

4. Setup and Wiring

Proper wiring is critical for the safe and correct operation of the BMS. Always ensure all connections are secure and follow the diagrams carefully. A collection line (balance wire harness) is included with the product.

HeltecBMS 30A module with included wiring harness

Figure 3: HeltecBMS 30A module with included wiring harness.

Wiring Diagram Overview:

The following diagrams illustrate the wiring for different string counts (6S to 16S). The general principle involves connecting the balance wires from each cell to the BMS, and the main battery terminals (B- and P-) to the BMS.

  • B-: Connects to the negative terminal of the battery pack.
  • P-: Connects to the negative terminal of the load/charger.
  • Balance Wires: Connect sequentially from the first cell (lowest voltage) to the last cell (highest voltage) of the battery pack.
Wiring diagram for 6S and 7S battery packs with HeltecBMS

Figure 4: Wiring diagrams for 6S and 7S battery packs.

Wiring diagram for 8S, 10S, 12S, 13S, 14S, and 16S battery packs with HeltecBMS

Figure 5: Wiring diagrams for 8S, 10S, 12S, 13S, 14S, and 16S battery packs.

Important: Always double-check your wiring before applying power to prevent damage to the BMS or battery pack.

5. Operating Principles and Protection Functions

The HeltecBMS continuously monitors the battery pack's voltage, current, and temperature to ensure safe operation and extend battery life. It activates various protection mechanisms when parameters exceed safe limits.

Protection Function Summary:

TypeOvercharge single string detection voltageOvercharge single string release voltageOver-discharge single string detection voltageOver-discharge single string release voltageSingle string balanced charging start
NCM4.25V ± 0.035V4.19V ± 0.025V2.8V ± 0.025V3.0V ± 0.025V4.2V ± 0.035V
LFP3.65V ± 0.035V3.55V ± 0.025V2.35V ± 0.025V2.55V ± 0.025V3.44V ± 0.035V

Over-temperature protection: Charging is optional. Low temperature protection activates at -0°C ± 5°C. High temperature protection activates at 75°C ± 5°C.

Short-circuit protection: Activated by external load circuit short circuit. Detection delay time is 300μS (MAX). Protection releases when short circuit is broken.

6. Troubleshooting

This section provides solutions for common issues you might encounter with your HeltecBMS.

Fault PhenomenonFault Inspection and CauseProcessing Method
Can't discharge1. Circuit not activated for charging. 2. Individual battery cell voltage is too low (NCM < 3.0V ± 0.025V / LFP < 2.35V ± 0.025V), triggering over-discharge protection.1. Connect the circuit to activate the protection board for charging. 2. Charge the battery to 3.7V (NCM) / 3.25V (LFP) and balance before combining. Do not mix good batteries with poor ones. Contact after-sales service if problem persists.
Can't chargeIndividual battery cell voltage is too high (NCM > 4.215V / LFP > 3.615V), triggering overcharge protection.Discharge the battery to about 3.7V until it is balanced before combining. Do not mix good batteries with poor ones. Contact after-sales service if problem persists.
Charging/discharge failureIncorrect wiring (B-, B1, B2, B3... B+).Redraw the wiring or operate under the guidance of customer service.
Overcharge/discharge protection is invalidIncorrect wiring (B-, B1, B2, B3... B+).Redraw the wiring or operate under the guidance of customer service.
Discharge protectionCurrent value of the load starting power supply exceeds the over-current protection current of the protection board.Replace the protection board with a larger current rating. Contact after-sales service if problem persists.
Component is welded looselyOne of the components has a pin that is not connected to the PCB pad.Repair the welding yourself. Contact after-sales service if problem persists.
Component welding (short circuit)There is a short circuit between two or more pins of the element.Remove the component and re-weld. Contact after-sales service if problem persists.
Electrostatic breakdownWhen the MOS tube is not powered, the forward and reverse resistance of any two pins of the G, D, and S terminals are 0.Remove and replace the MOS tube yourself. Contact after-sales service if problem persists.

7. Maintenance

To ensure the longevity and optimal performance of your HeltecBMS, follow these general maintenance guidelines:

  • Regular Inspection: Periodically check all wiring connections for tightness and signs of corrosion or damage.
  • Environmental Conditions: Operate the BMS within its specified temperature range. Avoid exposure to excessive moisture, dust, or corrosive environments.
  • Battery Health: Ensure the battery pack connected to the BMS is in good condition. Imbalanced or damaged cells can affect BMS performance.
  • Cleaning: If necessary, gently clean the BMS board with a soft, dry brush to remove any dust accumulation. Do not use liquids or solvents.

8. User Tips

  • Verify Connections: Before initial power-up, carefully double-check all wiring according to the provided diagrams to prevent any potential damage.
  • Cell Balancing: For optimal battery life, ensure your battery cells are balanced before connecting them to the BMS, especially if they have been stored for a long time.
  • Professional Installation: If you are unsure about any part of the installation or wiring process, it is recommended to seek assistance from a qualified professional.

9. Warranty and Support

9.1. Quality Guarantee

HeltecBMS guarantees that each product is shipped after being tested by professional protection board testing instruments. While every effort is made to ensure quality, the combination battery of the protection board may be damaged by static electricity and current, and it is normal to have defective products in use.

9.2. Warranty Regulations

  • Warranty Period: 1 year from the date of purchase.
  • Warranty Coverage: Limited to normal use. The warranty does not cover:
    • Man-made damage
    • Self-disassembly, modification, or repair
    • Use not in accordance with the instructions
    • Damage caused by external force majeure factors
  • Consumables: Accessories such as test fixtures are considered consumables and are not covered by warranty.
  • Warranty Service: For warranty service, please contact your dealer. If you cannot reach your dealer, contact HeltecBMS directly via email or phone.
  • International Service: There are no after-sales service stations in countries other than China. For international warranty service, you may need to send the product to HeltecBMS for free repair, but you will be responsible for the round-trip shipping costs.

© 2024 HeltecBMS. All rights reserved.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.