LAUNCH CR3001

Contents

LAUNCH CR3001 OBD2 Automotive Diagnostic Code Reader Scanner User Manual

Model: CR3001 | Brand: LAUNCH

1. Introduction

The LAUNCH CReader 3001 is a professional OBD2 automotive diagnostic code reader scanner designed to help users diagnose and clear engine fault codes. This tool supports all 10 modes of OBD II tests for comprehensive vehicle diagnosis. It features a 1.77-inch color LCD display, enabling users to easily read and clear Diagnostic Trouble Codes (DTCs), record and save data.

With built-in help menus and code definitions, diagnosing and resolving issues indicated by the Check Engine Light is made simpler. The CReader 3001 also includes bi-directional special tests such as EVAP, O2 Sensor, I/M Readiness, MIL Status, VIN Info, and On-board monitors testing.

The device can be connected to a PC via a USB cable for software updates, ensuring it stays current with the latest vehicle data and functionalities. Please note that the CReader 3001 may automatically reset if disturbed by strong static electricity, which is a normal operational characteristic.

This tool is designed to work with all OBD2 compliant vehicles, including those using the Controller Area Network (CAN) protocol. EPA regulations mandate that all 1996 and newer vehicles (cars and light trucks) sold in the United States must be OBD2 compliant. This includes all American, Asian, and European vehicles. For some 1994 and 1995 gasoline vehicles, OBD2 compliance can be verified by checking the Vehicle Emissions Control Information (VECI) Label, usually located under the hood or by the radiator, which should state "OBD II Certified". All OBD2 compliant vehicles are required to have a standard 16-pin Data Link Connector (DLC).

Vehicle Emissions Control Information (VECI) Label
Figure 1.1: Example of a Vehicle Emissions Control Information (VECI) Label, indicating OBD II certification.

2. Safety Precautions and Warnings

To prevent personal injury or damage to vehicles and/or the test equipment, please read this user's manual carefully and observe the following safety precautions at a minimum whenever working on a vehicle:

  • Always perform automotive testing in a safe environment.
  • Do not attempt to operate or observe the tool while driving a vehicle. Operating or observing the tool will cause driver distraction and could cause a fatal accident.
  • Wear safety eye protection that meets ANSI standards.
  • Keep clothing, hair, hands, tools, test equipment, etc., away from all moving or hot engine parts.
  • Operate the vehicle in a well-ventilated work area: Exhaust gases are poisonous.
  • Put blocks in front of the drive wheels and never leave the vehicle unattended while running tests.
  • Use extreme caution when working around the ignition coil, distributor cap, ignition wires, and spark plugs. These components create hazardous voltages when the engine is running.
  • Put the transmission in Park (P) for automatic transmission (A/T) or Neutral (N) for manual transmission (M/T) and make sure the parking brake is engaged.
  • Keep a fire extinguisher suitable for gasoline/chemical/electrical fires nearby.
  • Do not connect or disconnect any test equipment while the ignition is on or the engine is running.

3. Product Overview

The LAUNCH CReader 3001 is a compact and portable diagnostic tool designed for ease of use. Below is an outline of its main components and their functions:

LAUNCH CReader 3001 device with callouts
Figure 3.1: LAUNCH CReader 3001 device overview.
CReader 3001 Components and Functions
No. Name Description
1 OBD-16 connector To connect to the vehicle's DLC (Data Link Connector).
2 OK key To confirm the current operation.
3 Return key Back to the previous page.
4 USB port To connect to PC for system update via USB cable.
5 Down key Move cursor down for selection. Or skip to the next page when more than one page is displayed.
6 Up key Move cursor up for selection. Or skip to the previous page when more than one page is displayed.
7 LCD Indicates test results.
Video 3.1: A product demonstration showing the LAUNCH CReader 3001 in use, including connection and basic operation.

4. Setup: Preparation & Connection

  1. Turn the ignition off. Ensure the vehicle's ignition is completely off before connecting the device.
  2. Locate the vehicle's DLC socket. The Data Link Connector (DLC) is typically a 16-pin connector. It is usually located 12 inches from the center of the instrument panel (dash), under or around the driver's side for most vehicles. If not found under the dashboard, a label should indicate its location. For some Asian and European vehicles, the DLC might be behind the ashtray, requiring its removal.
  3. Plug the diagnostic cable into the vehicle's DLC. The cable connector is keyed and will only fit one way. If you encounter difficulty, rotate the connector 180 degrees and try again. A plastic DLC cover may be present on some vehicles and needs to be removed before plugging in the diagnostic cable.
    Turning off vehicle ignition
    Figure 4.1: Illustration of turning off the vehicle ignition.
    Connecting diagnostic cable to DLC
    Figure 4.2: Connecting the diagnostic cable to the vehicle's DLC.
  4. Turn the ignition on. The engine can be off or running.
  5. System Initialization. After connecting and turning on the ignition, the system will start initializing. Once initialized, the main menu interface will appear.

5. Operating Instructions

5.1. Settings

From the Main Menu, select [Tool Setup] and press [OK] to enter the tool setup screen.

  • Language: This option allows you to set the user interface language. The CR3001 supports English, French, Russian, Spanish, German, Italian, and Portuguese.
  • Unit of Measure: This option allows you to set the measurement unit (e.g., Metric or Imperial).
Language setting steps on CR3001
Figure 5.1: Steps to set the desired language on the CR3001.

5.2. Diagnose

After the tool is properly connected to the vehicle's DLC, select [Diagnose] in the Main Menu and press [OK]. The tool will automatically detect the vehicle's communication protocol (ISO 9141, Keyword 2000, J1850 PWM, J1850 VPW, or CAN) and establish a link. The Monitor Status screen will then be displayed.

Full OBD2 Functions of LAUNCH CR3001
Figure 5.2: Overview of full OBD2 functions available on the LAUNCH CR3001.

The Diagnostic Menu includes the following functions:

  • Read Codes: This function identifies which section of the emission control system has malfunctioned by displaying Diagnostic Trouble Codes (DTCs).
  • Erase Codes: After reading the retrieved codes and performing necessary repairs, this function allows you to clear the codes from the vehicle's computer. Ensure the ignition key is in the ON position with the engine off before performing this function.
  • I/M Readiness: This indicates whether the various emissions-related systems on the vehicle are operating properly and are ready for Inspection and Maintenance testing. It helps determine the vehicle's condition for SMOG tests.
  • Data Stream: This option retrieves and displays live data and parameters from the vehicle's Engine Control Unit (ECU). Live data is displayed in a time-based chart for better analysis of abnormal parameters.
    Live Data Stream display on CR3001
    Figure 5.3: Live Data Stream display showing engine parameters in real-time.
  • Freeze Frame: When an emission-related fault occurs, the on-board computer records certain vehicle conditions. This "freeze frame" data provides a snapshot of operating conditions at the time of the fault, guiding you to the problem area.
  • O2 Sensor Test: Retrieves and displays O2 sensor monitor test results for the most recently performed tests, helping to identify failures of oxygen sensors and related emissions errors.
  • On-Board Monitor Test (Mode 6): Retrieves and displays test results for emission-related powertrain components and systems that are not continuously monitored. This helps identify misfire or compression problems in specific cylinders or other issues not severe enough to trigger a Check Engine Light.
  • EVAP System Test (Mode 8): Initiates a leak test for the vehicle's EVAP system, which prevents fuel vapors from evaporating. This allows verification of fuel system repairs without waiting for the car to run the test automatically.
  • Vehicle Info: Displays information such as VIN (Vehicle Identification Number), CID (Calibration ID), and CVN (Calibration Verification Number) provided by the vehicle manufacturer.

5.3. DTC Lookup

This menu allows you to view the detailed definition of a retrieved DTC. From the Main Menu, select [DTC Lookup] and press [OK]. You can then input the DTC using the up/down keys to alter the value and the OK key to confirm. After viewing the definition, press the return key to go back to the Main Menu.

Plug and Play operation of CR3001
Figure 5.4: Plug and Play operation, showing connection and menu navigation.

6. Maintenance

To ensure the longevity and proper functioning of your CReader 3001, follow these maintenance guidelines:

  • Keep the test equipment dry, clean, and free from oil/water or grease.
  • Use a mild detergent on a clean cloth to clean the outside of the test equipment when necessary.

7. Troubleshooting (FAQ)

Q: System halts when reading data stream. What is the reason?
A: It may be caused by a slackened connector. Please turn off the tool, firmly connect the connector, and switch it on again.
Q: Screen of main unit flashes at engine ignition start.
A: Caused by electromagnetic disturbing, and this is a normal phenomenon.
Q: There is no response when communicating with the on-board computer.
A: Please confirm the proper voltage of power supply and check if the throttle has been closed, the transmission is in the neutral position, and the water is at the proper temperature.
Q: Why are there so many fault codes?
A: Usually, it's caused by poor connection or a faulty circuit grounding.
Q: Is the device compatible with Fiat Toro 2017 diesel 2x4?
A: Yes, user reviews indicate it works perfectly on newer Fiat models like the Fiat Uno 2011, suggesting compatibility with your 2017 Fiat Toro diesel 2x4.
Q: Does it work on a 2011 Renault Clio 1.0 16v?
A: The device supports European cars from 2003 onwards, so it should be compatible with a 2011 Renault Clio.
Q: Does it fit a 2011 Ford Focus?
A: Yes, the device supports US-based cars from 1996 onwards and European cars from 2003 onwards, so it should be compatible with a 2011 Ford Focus.
Q: Does it come in Portuguese?
A: Yes, the CR3001 operating system supports multiple languages, including Portuguese. You can set the language in the Tool Setup menu.
Q: Does it fit Palio 99 or Astra 99?
A: The device supports US-based cars from 1996 onwards and European cars from 2003 onwards. For models from 1999, it might work if they are OBD2 compliant, but compatibility is not guaranteed for all older models.
Q: Does this device work on a 2016 Fiat Gran Siena, and does it also diagnose brake sensors?
A: It should work on a 2016 Fiat Gran Siena as it supports newer Fiat models. However, OBD2 scanners primarily diagnose engine and emissions-related systems. While some brake system issues might trigger an engine code, it is not designed for comprehensive diagnosis of brake sensors or ABS systems.

8. Specifications

  • Screen: 1.77" color LCD
  • Input Voltage Range: 9~18V
  • Working Temperature: 0 to 50°C (32 to 122°F)
  • Storage Temperature: -20 to 70°C (-4 to 158°F)
  • External Dimension: 118mm x 68mm x 22.3mm (4.65" x 2.68" x 0.88")
  • Weight: <200g (0.44 lbs)

Package Information:

  • Length: 12 cm
  • Width: 10 cm
  • Height: 8 cm
  • Weight: 0.236 kg

9. Warranty & Support

9.1. Warranty Information

LAUNCH electronic products are warranted against defects in materials and workmanship for one year (12 months) from the date of delivery to the user. This warranty is expressly limited to persons who purchase LAUNCH products for purposes of resale or use in the ordinary course of business.

This warranty does not cover any part that has been abused, altered, used for a purpose other than for which it was intended, or used in a manner inconsistent with instructions regarding use. The exclusive remedy for any automotive meter found to be defective is repair or replacement. LAUNCH shall not be liable for any consequential or incidental damages.

Final determination of defects shall be made by LAUNCH in accordance with established procedures. No agent, employee, or representative of LAUNCH has any authority to bind LAUNCH to any affirmation, representation, or warranty concerning LAUNCH automotive meters, except as stated herein.

9.2. Customer Service

If you have any questions on the operation of the unit, please contact your local dealer, or contact LAUNCH TECH CO., LTD:

  • Tel: +86 755 8455 7891
  • E-mail: X431@cnlaunch.com

10. User Tips

  • The CR3001 has been successfully used on various vehicle models including Fiat Uno 2011, 2023 Voyage, and Azera 2009, indicating broad compatibility with modern OBD2 vehicles.
  • This tool provides basic diagnostics. For highly specialized or professional-grade diagnostics beyond engine and emissions systems, more advanced tools may be required.
  • Ensure the device is properly connected and the ignition is on for accurate readings and to avoid communication issues.

© 2024 LAUNCH TECH CO., LTD. All rights reserved.


Documents and downloads

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.