SIMICAM SMPO08

Contents

SIMICAM SMPO08 4K 8CH POE Smart NVR User Manual

Model: SMPO08 | Brand: SIMICAM

1. Introduction

Thank you for choosing the SIMICAM SMPO08 4K 8CH POE Smart NVR. This Network Video Recorder is designed to provide high-quality surveillance and recording capabilities for your security system. This manual will guide you through the installation, operation, and maintenance of your NVR system. Please read it carefully before use and keep it for future reference.

Safety Cautions:

  • Always modify the default user password immediately after setup to prevent unauthorized access.
  • Do not install the NVR in wet, dusty, or easily accessible locations for children.
  • Ensure the installation area is well-ventilated; do not block the air vents.
  • Operate and store the NVR within the allowed temperature range. Do not attempt to dismantle the unit.
  • This product is suitable for safe use in non-tropical climates.
  • Product instructions are for reference; actual product features may prevail. Information is subject to change without notice.

2. Package Contents

Please check the box for the following items. Depending on the product model, accessories may vary.

Item Quantity
NVR Unit1
IP Cameras (IPC)4 (typical for 4CH models)
Power Adapter1
USB Mouse1
Certificate1
Instructions Manual1
Network Cables4

3. Product Overview

3.1. NVR Unit

The SIMICAM NVR features a sleek design with indicators for power, HDD activity, and alarms. It supports 4K Ultra HD display and intelligent face detection.

SIMICAM NVR Front and Back Panels with Remote

Description: Image showing the SIMICAM NVR from the front with power, HDD, and alarm indicators, and control buttons. Below it are two views of the NVR's rear panel, one for a 4-channel and one for an 8-channel configuration, detailing PoE ports, power input, video outputs (VGA, HDMI), and USB ports. A remote control is also pictured. Key features like '4K Ultra HD Display', '8CH POE', 'Face detection', 'H.265 HEVC' are highlighted.

3.2. Back Panel Interface

The rear panel of the NVR provides all necessary ports for power, network, video output, audio, and peripheral connections.

NVR Back Panel Connections Diagram

Description: A diagram illustrating the rear panel of the NVR with various ports labeled and connected to their respective devices. From left to right: PoE Link ports (for PoE Cameras), ON/OFF switch, DC 48V power input (for Power Adapter), A-OUT (for Audio Out), VGA (for VGA Display), HD-port (for HDMI Display), LAN (for Router), and USB ports (for Mouse & UFD). Devices like Phone/Tablet are shown connecting via the Router.

Icon/Port Name/Function
DC Power InputConnects to the power adapter (DC 48V)
Power SwitchTurns the NVR on or off
VGA OutputConnects to a VGA monitor
HDMI OutputConnects to an HDMI display
Internet Interface (LAN)Connects to your network router
USB InterfaceFor USB mouse, USB flash drive (UFD)
A-INAudio Frequency Input
A-outAudio Frequency Output
Alarm-inAlarm input port
Alarm-outAlarm output port
RS485RS485 Interface (for PTZ control)
RS232RS232 Interface
BNC OutputBNC Video Output

4. Setup Instructions

4.1. Hard Disk Installation (Optional)

If you intend to store recordings, you will need to install a 3.5'' SATA hard disk drive (HDD). Professional monitoring hard disks are recommended for optimal performance.

  1. Remove Cover: Unscrew the side and tail board screws, then carefully remove the cover board.
  2. Connect HDD: Connect the power and data cables from the NVR to the hard disk.
  3. Secure HDD: Use screws to fasten the hard disk securely to the chassis baseplate.
  4. Close Cover: Align the cover board with the card slots, close it, and tighten the screws.

4.2. Connection Diagram

Follow this diagram to connect your NVR system components.

NVR Connection Diagram from Manual

Description: A diagram from the user manual showing how to connect the NVR system. POE IP Cameras connect directly to the POE NVR via network cables. The NVR connects to a Monitor via HDMI/VGA and a Mouse via USB. A power adapter connects to the NVR. Note: POE IP Cameras do not require separate power supplies; they receive power through the network cable from the NVR.

  • Connect POE IP Cameras to the NVR's POE Link ports using network cables.
  • Connect a monitor to the NVR's VGA or HDMI output port.
  • Connect the USB mouse to one of the NVR's USB ports.
  • Connect the NVR to your router via the LAN port for internet access.
  • Connect the power adapter to the NVR's DC 48V input.
  • Important: Turn on the power only after all connections are made. POE IP Cameras do not need separate power; they are powered directly by the NVR via the network cable.

4.3. Power On Operation & Initialization

  1. Power On: Turn on the NVR (if it has a power switch, ensure it's in the ON position). Wait for the system to start up.
  2. Auto Configuration: After power-on, the NVR will typically enter 'Auto Configuration'. It will automatically connect to front-end IP Cameras that are enabled with DHCP.
  3. System Time Setting: The system will prompt you to set the time zone, system time, and date format.
  4. Password Modification: You will be prompted to modify the default password. It is crucial to change this immediately for security.
  5. Output Mode Setting: You can configure channel titles, time titles, and other display settings.

4.4. Network Setup

For remote viewing and internet features, ensure your NVR is properly connected to your network.

  1. Connect the NVR's LAN port to your router using an Ethernet cable.
  2. Navigate to Main Menu > Network Settings > Network Test.
  3. Verify the network connection by checking Gateway, Network, and DNS tests. If unsuccessful, adjust network settings (IP address, subnet mask, gateway, DNS) to match your network configuration.

5. Operating Instructions

5.1. Front Panel Key Instruction

The front panel buttons allow for direct control of the NVR. Note that not all functions may be available on all models.

Icon Name/Function Icon Name/Function
Play/PausePlay/Pause videoPower indicator lightPower status
Play the last fileGo to previous fileLink indicator lightNetwork link status
Play the next fileGo to next fileRecord indicator lightRecording status
Playback/PausePlayback controlShift indicator lightShift function
Stop playbackStop current playbackAlarm indicator lightAlarm status
SearchVideo searchESCCancel operation
AlarmAlarm-out controlModePicture drift control
Zoom-Zoom decreaseRECVideo control
Zoom+Zoom increasePTZCloud control
PresetPreset controlMenuMain menu access
USB interfaceUSB portShiftShift function
DirectionNavigation/PTZ controlFNAssistant function
OKConfirm selectionShuttleShuttle control

5.2. Record Setting

The NVR can automatically detect channels with video input and start recording. To customize recording settings:

  • Right-click on the display to access the Main Menu.
  • Navigate to Record > Record Conf..
  • Channel: Select specific channels or 'All' for global settings.
  • Length: Set the duration of each video file (default is 60 minutes).
  • Period: Configure time segments for recording (e.g., schedule recording for specific hours).
  • Video Type: Select the video type for easier search during playback.

5.3. Video Playback

To view recorded footage:

  • Right-click on the display to access the Main Menu.
  • Navigate to Record > Playback.
  • Use the playback controls (play, pause, stop, fast forward, rewind).
  • Select the video type, choose playback channels, view by calendar time, or view by file list.

5.4. Face Detection and Playback

The NVR supports intelligent face detection, allowing you to record and playback events based on detected faces.

Face Playback Feature

Description: An image demonstrating the 'Face Playback' feature. It shows a timeline with detected faces captured at different times (e.g., 09:00, 09:30, 10:55). Below, a live view of an office space is shown with multiple small windows displaying detected faces from the surveillance feed, indicating active face detection.

5.5. Email Notifications

Configure the NVR to send email notifications upon detection of motion or other alarm events.

Email Notifications Feature

Description: An image illustrating the email notification feature. A masked intruder is shown in a living room, highlighted by a red box, with email icons floating towards the user's smartphone, which displays a live view of the scene. This indicates that an alert has been triggered and sent via email.

5.6. Internet Access and Remote Viewing

Access your NVR remotely using various methods:

  • IE Access:
    1. Ensure the NVR and your PC are on the same network segment.
    2. Open Internet Explorer and enter the NVR's IP address (e.g., 192.168.1.9) in the address bar.
    3. Click 'download plug-in', install it, then log in with your username and password to view and manage the device.
  • PC VMS Video Management System:
    1. Access baike.xm030.cn, navigate to Download Center > Software > PC Client > VMS.
    2. Install the VMS client, then add your NVR devices to view and manage.
  • Cloud Platform:
    1. Visit the cloud service website: www.xmeye.net.
    2. Use the 'new users guide' to register an account, log in, and add your device for remote management.
  • Mobile APP Access:
    1. Search for 'XMeye' in your mobile app store (e.g., Google Play Store, Apple App Store).
    2. Download and install the app.
    3. Register an account, log in, and add your device (using the serial number QR code or manual input) for remote viewing and management.

6. Maintenance

  • Cleaning: Gently wipe the NVR's exterior with a soft, dry cloth. Do not use liquid cleaners or aerosols.
  • Environment: Ensure the NVR is kept in a dry, dust-free, and well-ventilated area. Avoid direct sunlight and extreme temperatures.
  • Firmware Updates: Periodically check the manufacturer's website or app for firmware updates to ensure optimal performance and security.
  • Password Security: Regularly change your NVR's password and use strong, unique passwords.
  • Hard Drive Health: If using an HDD, monitor its health through the NVR's system settings to prevent data loss.

7. Troubleshooting

  • No Image from Cameras:
    • Ensure cameras are properly connected to PoE ports.
    • Verify network settings for both NVR and cameras (IP addresses, subnet masks).
    • Check camera compatibility (NVR supports ONVIF protocol; some specific brands like Hikvision or Reolink may require specific configurations or might not be fully compatible).
    • Restart the NVR and cameras.
  • Hard Disk Not Recognized:
    • Ensure the HDD is correctly installed and connected (power and data cables).
    • Check if the HDD works when connected to a PC. If so, try formatting it via the NVR's system settings.
    • Perform a factory reset of the NVR (see below).
  • Network Configuration Issues:
    • Verify the Ethernet cable connection to the router.
    • Check NVR's IP address, gateway, and DNS settings. Ensure they are compatible with your local network.
    • Perform a network test from the NVR's menu.
  • View on Monitor Not Clear:
    • Check the resolution settings of the NVR's video output (VGA/HDMI) to match your monitor's native resolution.
    • Ensure the monitor itself supports the output resolution of the NVR.
  • How to Factory Reset:
    • Access the NVR's Main Menu > System > Default or Restore option. Follow on-screen prompts. Note that this will erase all custom settings.

8. Specifications

Feature Specification
Model NumberSMPO08
Brand NameSIMICAM
Supported Operating SystemsMicrosoft Windows 7, Mac OS
Communication InterfaceRS485
Network InterfaceRJ45 10/100M
Hard Drive Size3.5''
Hard Drive Interface TypeSATA
Video StandardNTSC, PAL
Video Input InterfaceRJ45 (PoE)
Compression FormatH.265
TechnologyNetwork
Alarm TypeEmail Photo, Local Alarm
Video OutputVGA, HDMI
Max. IP Camera Support8 x 8MP/4K IP Cameras

9. User Tips

  • Simple Setup: Many users find the installation and initial setup, including connecting PoE cameras and setting up the hard drive, to be straightforward.
  • Network Configuration: If you encounter issues, double-check your network settings. Minor adjustments can often resolve connectivity problems.
  • Control Options: While the front panel buttons are available, using the included USB mouse or remote control often provides a more convenient and intuitive way to navigate the NVR's interface.
  • Monitor Clarity: If the display on your monitor isn't as clear as expected, verify that the NVR's video output resolution matches your monitor's native resolution for the best picture quality.
  • Language Support: Be aware that the NVR's interface may have limited language support (e.g., Hebrew or Arabic might not be supported).

10. Frequently Asked Questions (FAQ)

Q: Is this NVR compatible with specific camera brands like Hikvision or Reolink?
A: The NVR generally supports ONVIF-compliant IP cameras. However, specific features or full compatibility with certain proprietary camera brands (e.g., Hikvision, Reolink Duo2) cannot be guaranteed without testing. Ensure your cameras support ONVIF protocol.
Q: What type of network cable should I use?
A: The NVR uses an RJ45 10/100M network interface. Cat5e or Cat6 Ethernet cables are generally sufficient for reliable performance with PoE and data transmission.
Q: What plug type is included for my region (e.g., Mexico)?
A: The NVR typically comes with regional plug types (US, EU, UK, AU). Please select the appropriate plug type when purchasing or ensure you have a compatible adapter for your region.
Q: Can I connect cameras with color night vision and facial recognition?
A: The NVR supports facial recognition features. For specific camera capabilities like color night vision, the camera itself must support these features, and the NVR will record what the camera provides.

11. Warranty and Support

Warranty Information:

This product comes with a one-year warranty period from the date of purchase. During this period, if any breakdown occurs due to a product defect, please contact your dealer or our after-sale service department.

The warranty does not cover:

  • Damage caused by personal reasons, incorrect usage, or force majeure.
  • Breakdowns resulting from maintenance, refitting, or dismantling by unauthorized personnel.
  • Damage due to lack of a valid warranty certificate, purchasing invoice, or receipt.
  • Damage occurring after the warranty period has expired.

Please ensure to keep your warranty card and purchase receipt for service requests.

For further assistance, please refer to the official SIMICAM support channels or contact your retailer.

A PDF version of the user manual may be available for download at the seller's product page: User Manual (PDF)

© 2023 SIMICAM. All rights reserved.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.