NOKLEAD 5253

Contents

NOKLEAD Indoor Temperature Humidity Meter

Model: 5253

1. Introduction

Thank you for choosing the NOKLEAD Indoor Temperature Humidity Meter. This device provides accurate, real-time measurements of indoor temperature and humidity, along with time and date display. Its compact design and multiple mounting options make it a versatile addition to any household. Please read this manual carefully before use to ensure proper operation and to maximize the lifespan of your device.

2. Safety Information

  • Do not expose the device to extreme temperatures or direct sunlight for prolonged periods.
  • This product is not waterproof. Avoid contact with water or high moisture environments.
  • Do not mix old and new batteries, or different types of batteries.
  • Remove the battery if the device will not be used for an extended period to prevent leakage.
  • Keep out of reach of children.

3. Package Contents

  • NOKLEAD Indoor Temperature Humidity Meter (Model 5253)
  • CR2032 Button Battery (pre-installed or included separately)
  • Adhesive Metal Plate for magnetic mounting
  • User Manual

4. Product Overview

The device features a large LCD display for easy readability and intuitive controls.

Front view of the white thermometer/hygrometer displaying temperature, humidity, time, and date.
Front view of the device (White variant)
Rear view of the device showing the battery compartment, control buttons, and kickstand.
Rear view with battery compartment and controls

Key Features:

Infographic highlighting key features: Thermometer, Hygrometer, Comfort Level, °C/°F Selector, 10s Refresh, CR2032 Battery, Date, 12/24 HR Switch.
Highlighted features of the device

The display includes a comfort level indicator:

  • DRY: Humidity < 30%
  • COMFORT: 30% ≤ Humidity ≤ 69%
  • WET: Humidity ≥ 70%
Display showing humidity ranges for Dry (<30%), Comfort (30%-69%), and Wet (>=70%).
Humidity Comfort Level Indicator

5. Setup

5.1. Battery Installation

  1. Locate the battery compartment on the back of the device.
  2. If a plastic tab is present, gently pull it out to activate the pre-installed CR2032 button battery.
  3. If installing a new battery, open the battery compartment cover and insert one CR2032 button battery with the correct polarity (+ side up).
  4. Close the battery compartment cover securely.

Upon successful battery installation, the LCD display will show a full screen for approximately 2 seconds before displaying current readings.

5.2. Initial Power On

The device powers on automatically once the battery is installed or activated. No additional power button press is required for initial startup.

6. Operation

6.1. Date and Time Setting

  1. Press and hold the "SET" button for a few seconds until the hour digit begins to flash.
  2. Use the "+" and "-" buttons to adjust the hour.
  3. Press the "SET" button to confirm the hour and move to the minute setting.
  4. Repeat steps 2 and 3 to set the minutes, 12/24-hour format, year, month, and day.
  5. After setting the day, press "SET" one last time to save all settings and exit the time/date setting mode.

The device will automatically exit the setting mode after 15 seconds of inactivity.

6.2. 12/24 Hour Format Selection

While in time setting mode (when the hour or minute is flashing), press the "SET" button to cycle through the 12-hour (AM/PM) and 24-hour formats.

6.3. Temperature Unit Selection (°C/°F)

Press the "+" button once to switch between Celsius (°C) and Fahrenheit (°F) temperature units.

7. Mounting Options

The NOKLEAD Temperature Humidity Meter offers flexible placement options:

  • Desktop Placement: Use the integrated kickstand on the back of the device to place it on any flat surface.
  • Magnetic Mounting: The device has a magnetic back, allowing it to be directly attached to metal surfaces like refrigerators or magnetic boards.
  • Wall Mounting (Non-Metal Surfaces): For non-metal surfaces, use the provided adhesive metal plate. Stick the adhesive side of the plate to your desired wall location, then attach the device magnetically to the metal side of the plate.
Demonstration of magnetic mounting using an adhesive metal plate.
Magnetic mounting with adhesive plate

8. Calibration

This device supports calibration for both temperature and humidity readings to ensure accuracy. While the exact button sequence for entering calibration mode is not detailed in the provided information, typically, calibration modes are accessed by pressing and holding a combination of buttons (e.g., "SET" and "+" or "-") for several seconds. Once in calibration mode, the display will usually flash, allowing you to adjust the readings using the "+" and "-" buttons. Press "SET" to confirm and save the calibration.

Refer to the full PDF user manual for detailed calibration instructions if needed: View User Manual (PDF)

9. Maintenance

  • Cleaning: Clean the display and casing with a soft, dry cloth. Do not use abrasive cleaners or solvents.
  • Battery Replacement: When the screen display becomes dim or unreadable, it's time to replace the CR2032 button battery. Follow the battery installation steps in Section 5.1.

10. Troubleshooting

Problem Possible Cause Solution
Display is blank or dim Battery is dead or incorrectly installed. Replace the CR2032 battery, ensuring correct polarity.
Incorrect time/date displayed Time/date not set correctly. Follow the instructions in Section 6.1 to set the time and date.
Inaccurate temperature/humidity readings Device needs calibration or is placed in an unsuitable environment. Refer to Section 8 for calibration. Ensure the device is not near heat sources, vents, or direct sunlight.
Cannot switch between °C/°F Incorrect button pressed or device is in setting mode. Ensure the device is not in time/date setting mode. Press the "+" button to toggle temperature units.

11. Specifications

Feature Specification
Model Number 5253
Measure Type CU50 (Thermometer Hygrometer)
Display Type DIGITAL LCD
Humidity Accuracy ±5%RH
Max Measuring Temperature 50°C - 69°C (Note: This range may refer to the comfort zone or a specific operating range. Typical room temperature range is expected.)
Power Source CR2032 Button Battery (Battery Included: Yes)
Battery Life Approximately 12 months (may vary with usage)
Display Size 2.0 - 3.9 Inches (88.84mm large screen)
Style Standing and Wall Hanging
Product Dimensions (approx.) 66mm (Length) x 71mm (Width)
Product Weight (approx.) 84g
Smart Device No
Origin Mainland China

12. User Tips

  • Placement: For accurate readings, place the device away from direct heat sources (like radiators or direct sunlight), air conditioning vents, or areas with high airflow.
  • Multiple Rooms: Due to its compact size, consider purchasing multiple units to monitor temperature and humidity in different rooms, such as bedrooms, living areas, or even grow rooms.
  • Magnetic Mounting: Utilize the magnetic back for convenient placement on metal surfaces. For non-metal surfaces, the included adhesive metal plate provides a secure and easy mounting solution.
  • Calibration: If you suspect readings are inaccurate, take advantage of the calibration feature to fine-tune the device against a known standard.
  • Battery Life: While the battery life is generally long, some users report varied experiences. Keep a spare CR2032 battery on hand for quick replacement if the display dims unexpectedly.
  • No Backlight: Be aware that the display does not have a backlight, which may affect readability in low-light conditions.

13. Warranty & Support

The NOKLEAD Indoor Temperature Humidity Meter comes with:

  • 18-Month Warranty: For quality-related issues.

For any questions, support, or warranty claims, please contact customer service:

Email: support@noklead.com

You can also refer to the official user manual PDF for more detailed information: View User Manual (PDF)

14. Product Video

Watch this video for a quick overview of the product's features and usage:

Product demonstration showing setup, display features, and mounting options.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.