XCMT Chain Slider Sliding Swingarm Guide

Contents

Motorcycle Chain Slider and Swingarm Guide

Model: Chain Slider Sliding Swingarm Guide | Brand: XCMT

1. Introduction

This manual provides essential information for the proper installation, maintenance, and safe use of your XCMT Motorcycle Chain Slider and Sliding Swingarm Guide. Please read these instructions thoroughly before installation and retain for future reference.

This product is an aftermarket motorcycle accessory designed for specific KTM and Husqvarna models. For a comprehensive list of compatible models, please refer to the specifications section.

2. Safety & Warnings

  • This product is designed for specific motorcycle models only. Installation on non-compatible vehicles may lead to improper fitment, functional failure, or safety hazards.
  • Installation must be performed by a qualified motorcycle technician to ensure correct fitment and operation.
  • A torque wrench must be used during installation to tighten all bolts to the specified torque value. Never tighten by hand; over-torquing can strip threads, while under-torquing may cause the part to detach during riding.
  • Inspect the part before every ride. Discontinue use immediately if looseness, deformation, or cracks are detected.
  • This is a non-OEM (aftermarket) part. Its performance may differ from original equipment. Carefully assess your intended usage scenario.
  • Do not weld, drill, grind, or otherwise modify this product.

3. Specifications

AttributeValue
Brand NameXCMT
Model NameChain Slider Sliding Swingarm Guide For KTM
Item TypeCovers & Ornamental Mouldings
MaterialPolyurethane
Item Weight0.22kg
Package Length14 cm
Package Width12 cm
Package Height2 cm
Motobike MakeKTM

3.1. Compatible Models

This product is compatible with the following motorcycle models:

For KTM:

  • 125 XC (2016–2022)
  • 125 SX (2016–2022)
  • 150 XC (2016–2021)
  • 150 SX (2016–2021)
  • 250-450 SX-F (2016–2022)
  • 250-450 XC-F (2016–2021)
  • 125-500 XC-W (2017–2021)
  • 125-500 XCF-W (2017–2021)
  • 125-500 EXC (2017–2023)
  • 125-500 EXC-F (2017–2023)
  • 250 SX (2017-2021)
  • 300 SX (2017-2021)
  • 250 XC (2017-2021)
  • 300 XC (2017–2021)

For Husqvarna:

  • FC 250/350/450 (2016-2022)
  • FE 250/350/450/501 (2017-2022)
  • FE 350S (2021)
  • FE 501S (2021)
  • FS 450 (2016-2020)
  • FX 350/450 (2017-2021)
  • TC 125 (2016-2021)
  • TC 250 (2017-2021)
  • TE 150 (2017-2019)
  • TE 150I (2020-2021)
  • TE 250/300 (2017-2018)
  • TE 250i/300i (2018-2022)
  • TX 125/300 (2017-2019)
  • TX 300I (2020-2021)

4. Package Contents

The package includes:

  • 1 x Chain Slider
  • 1 x Swingarm Guide

Note: Fasteners are typically included with the product. Please verify upon receipt.

5. Installation Instructions

Important: Installation should be performed by a qualified motorcycle technician. Always use appropriate tools, including a torque wrench.

  1. Prepare the Motorcycle: Park the motorcycle on a level surface and engage the main stand to ensure stability.
  2. Remove OEM Component: Use appropriate tools to carefully remove the original OEM chain slider and/or swingarm guide.
  3. Position New Part: Align the new chain slider and swingarm guide with the existing mounting holes on your motorcycle's swingarm.
  4. Insert Fasteners: Insert the included fasteners through the mounting holes.
  5. Tighten Bolts: Tighten all bolts using a torque wrench to the specified torque value. Refer to your motorcycle's service manual for specific torque specifications. Do not overtighten or undertighten.
  6. Test Stability: After installation, manually apply pressure to the newly installed parts to test their stability. Ensure there is no unusual noise, play, or movement.
Orange chain slider and swingarm guide installed on a KTM motorcycle
Image: Orange chain slider and swingarm guide installed on a KTM motorcycle.
Orange chain slider and swingarm guide set
Image: Orange chain slider and swingarm guide set.
Black chain slider and swingarm guide set
Image: Black chain slider and swingarm guide set.
Blue chain slider and swingarm guide set
Image: Blue chain slider and swingarm guide set.

6. Maintenance Recommendations

  • Fastener Tightness: Check the tightness of all fasteners every 500 kilometers or at least once per month. Retighten to specified torque values if necessary.
  • Cleaning: Clean the chain slider and swingarm guide with water and a neutral detergent. Avoid using strong acids or alkalis, as these can cause corrosion or damage to the material.
  • Increased Inspection: If the motorcycle is frequently used in off-road, muddy, or salt-spray environments, increase the frequency of inspection to ensure optimal performance and safety.

7. Troubleshooting

If you encounter any issues with your chain slider or swingarm guide, consider the following:

  • Loose Fitment: Recheck all fasteners for proper torque. Ensure the part is correctly aligned with the mounting points.
  • Unusual Noise or Movement: This could indicate improper installation or wear. Inspect the part for any signs of damage, looseness, or incorrect positioning. If issues persist, consult a qualified motorcycle technician.
  • Excessive Wear: Ensure your chain is properly maintained, lubricated, and tensioned. Excessive chain wear can accelerate wear on the slider and guide.

8. User Tips

  • Regularly clean your chain and the chain slider/swingarm guide to prevent dirt and debris buildup, which can cause premature wear.
  • Always double-check torque specifications for all fasteners, as this is crucial for both performance and safety.
  • Consider the riding conditions; more aggressive riding or harsh environments may require more frequent inspections and maintenance.

9. Disposal

When the product reaches the end of its lifespan, it should be disposed of as metal/plastic waste through local recycling facilities or authorized waste collection points. Do not dispose of it randomly in general waste.

10. Warranty & Support

For any questions regarding this product, installation, or potential issues, please contact the seller or manufacturer directly. Keep your purchase records for reference.

A user manual in PDF format is also available for download: View User Manual (PDF)

11. Compliance Information

This product is a motorcycle accessory designed and verified in accordance with the following requirements:

  • Complies with the essential safety requirements of the EU General Product Safety Regulation (GPSR).
  • Materials and structural design meet standards for impact resistance, corrosion resistance, and load-bearing strength.
  • The CE marking has been affixed to the product or its packaging where applicable.

Note: This is an aftermarket replacement or modification part. Some models are not E-mark certified and are intended for off-road/closed-course use only. Do not use on public roads unless explicitly labeled as "E-marked."

12. Disclaimer

The manufacturer (Yongkang Sanyi Trading Co., Ltd) and EU Authorized Representative (MJCM SARL) shall not be held liable for any damage, injury, or accident resulting from:

  • Incorrect or unqualified installation.
  • Use beyond the intended scope (e.g., on public roads without E-mark certification, if not explicitly E-marked).
  • Unauthorized modifications to the product.
  • Failure to inspect or maintain the product as instructed in this manual.

This manual may be updated without prior notice. Please refer to the latest version for current information.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.